AGAlain Gérard

Alain Gérard

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Alain Gérard has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Dynamic characterization of machining systems

    by Miron Zapciu, Jean-Yves K’nEvez, Alain Gérard, Olivier Cahuc, Claudiu Florinel Bisu


  • Open Access

    Self-excited vibrations in turning: cutting moment analysis

    by Olivier Cahuc, Jean-Yves K'Nevez, Alain Gérard, Philippe Darnis, Gaëtan Albert, Claudiu F. Bisu, Céline Gérard

    This work aims at analysing the moment effects at the tool tip point and at the central axis, in the framework of a turning process. A testing device in turning, including a six-component dynamometer, is used to measure the complete torsor of the cutting actions in the case of self-excited vibrations. Many results are obtained regarding the mechanical actions torsor. A confrontation of the moment components at the tool tip and at the central axis is carried out. It clearly appears that analysing moments at the central axis avoids the disturbances induced by the transport of the moment of the mechanical actions resultant at the tool tip point. For instance, the order relation between the components of the forces is single. Furthermore, the order relation between the moments components expressed at the tool tip point is also single and the same one. But at the central axis, two different order relations regarding moments are conceivable. A modification in the rolling moment localization in the (y, z) tool plan is associated to these two order relations. Thus, the moments components at the central axis are particularly sensitive at the disturbances of machining, here the self-excited vibrations.

  • Open Access

    The Regenerative Vibrations Influence on the Mechanical Actions in Turning

    by Claudiu-Florinel Bisu, Raynald Laheurte, Alain Gérard, Jean-Yves K'Nevez

    In manufacturing during the cutting process the appearance of vibrations can not be avoided. These vibrations constitute a major obstacle to obtain a greater productivity and a better quality of the workpiece. It is thus necessary to develop models which make it possible to study, the totality of the 3D dynamic phenomena. Thanks to an experimental approach the complete torque of the mechanical actions is measured in the presence of the vibrations during a turning operation. This study makes it possible to analyze the variations of the central axis which is a significant parameter of the vibratory phenomena.

  • Open Access

    Metrology Influence on the Cutting Modelisation

    by Olivier Cahuc, Alain Gérard

    High speed machining has been improved thanks to considerable advancement on the tools (optimum geometry, harder materials), on machined materials (increased workability and machining capacity for harder workpieces) and finally on the machines (higher accuracy and power at the high speeds, performances of the numerical control system). However at such loading velocities, the cutting process generates high strain and high-speed strain which cause complex, various and irreversible phenomena in plasticity. These phenomena are comprehended through the complete measurement of the mechanical actions using a six-component dynamometer and flux and temperatures measurements at the tip of the cutting tool. Balanced energy assessments are the starting points of our reflection on the machining modelling. The modelling of these phenomena and the material behaviour under this type of loading requires a suitable theoretical approach. The main points of the strain gradient theory are developed. A theoretical behaviour law adapted to the cutting phenomena is then expressed.

  • Open Access

    Optimization and Dynamic Characterization System Part in Turning

    by Claudiu-Florinel Bisu, Constantin Ispas, Alain Gérard, Jean-Yves K'Nevez

    The appearance of the self-sustained vibrations corresponds to the dynamic instability of the machine tool. An experimental device and a model were designed to characterize the cutting system, the block part. This analysis shows the need for knowing more details of it the behavior of the coin at the time of the cut, and for envisaging for the continuation the appearance of vibrations.

  • Open Access

    Three-Dimensional Dynamic Cutting Model

    by Constantin Ispas, Claudiu-Florinel Bisu, Alain Gérard, Doru Bardac

    The determination of a dynamic law of cut is complex and often very difficult to develop. Several formulations were developed, in very complex ways being given that 3 AD crosses from there, the number of variables is much higher than out of orthogonal cut. The existence of the plan of displacements and the correlations with the elastic characteristics of the machining system thus make it possible to simplify the dynamic model 3D. A dynamic model on the basis of experimental approach is proposed. Simulation is in concord with the experimental results.

  • Open Access

    Self-Excited Vibrations in Turning: Efforts Torsor and Average Friction Coefficient Analysis

    by Alain Gérard, Olivier Cahuc, Miron Zapciu

    An experimental device in turning including, in particular, a six-component dynamometer is exploited to measure the complete torque of cutting forces in a case of self-excited vibrations. For the tests, the tool used is type TNMA 16 04 12 carbide not covered (nuance carbide-SUMITIMO ELECTRIC), without chip breeze. The machined material is an alloy of chrome molybdenum type 42 CrMo24. The test-tubes are cylindrical with a diameter of 120 mm and a length of 30 mm. The effort of analysis relates to the moments. In particular, to the tool tip point, when feed rate increases the friction coefficient of swivelling is increasing while that of bearing is decreasing. Innovative remarks on the evolution of the average friction coefficient for various depths of cut and feed rate are presented

  • Open Access

    Displacements analysis of self-excited vibrations in turning

    by Claudiu-Florinel Bisu, Philippe Darnis, Alain Gérard, Jean-Yves K'Nevez

    The actual research deals with determining by a new protocol the necessary parameters considering a three-dimensional model to simulate in a realistic way the turning process on machine tool. This paper is dedicated to the experimental displacements analysis of the block tool / block workpiece with self-excited vibrations. In connexion with turning process, the self-excited vibrations domain is obtained starting from spectra of two accelerometers. The existence of a displacements plane attached to the tool edge point is revealed. This plane proves to be inclined compared to the machines tool axes. We establish that the tool tip point describes an ellipse. This ellipse is very small and can be considered as a small straight line segment for the stable cutting process (without vibrations). In unstable mode (with vibrations) the ellipse of displacements is really more visible. A difference in phase occurs between the tool tip displacements on the radial direction and on the cutting one. The feed motion direction and the cutting one are almost in phase. The values of the long and small ellipse axes (and their ratio) shows that these sizes are increasing with the feed rate value. The axis that goes through the stiffness center and the tool tip represents the maximum stiffness direction. The maximum (resp. minimum) stiffness axis of the tool is perpendicular to the large (resp. small) ellipse displacements axis. FFT analysis of the accelerometers signals allows to reach several important parameters and establish coherent correlations between tool tip displacements and the static - elastic characteristics of the machine tool components tested.

  • Open Access

    New method to characterize a machining system: application in turning

    by Claudiu-Florinel Bisu, Jean-Yves K'Nevez, Philippe Darnis, Raynald Laheurte, Alain Gérard

    Many studies simulates the machining process by using a single degree of freedom spring-mass sytem to model the tool stiffness, or the workpiece stiffness, or the unit tool-workpiece stiffness in modelings 2D. Others impose the tool action, or use more or less complex modelings of the efforts applied by the tool taking account the tool geometry. Thus, all these models remain two-dimensional or sometimes partially three-dimensional. This paper aims at developing an experimental method allowing to determine accurately the real three-dimensional behaviour of a machining system (machine tool, cutting tool, tool-holder and associated system of force metrology six-component dynamometer). In the work-space model of machining, a new experimental procedure is implemented to determine the machining system elastic behaviour. An experimental study of machining system is presented. We propose a machining system static characterization. A decomposition in two distinct blocks of the system "Workpiece-Tool-Machine" is realized. The block Tool and the block Workpiece are studied and characterized separately by matrix stiffness and displacement (three translations and three rotations). The Castigliano's theory allows us to calculate the total stiffness matrix and the total displacement matrix. A stiffness center point and a plan of tool tip static displacement are presented in agreement with the turning machining dynamic model and especially during the self induced vibration. These results are necessary to have a good three-dimensional machining system dynamic characterization.

  • Open Access

    Determination Du Centre De Raideur Pour Les Machines-Outils - Application Au Tournage

    by Claudiu-Florinel Bisu, Jean-Yves K'Nevez, Philippe Darnis, Olivier Cahuc, Raynald Laheurte, Alain Gérard

    The determination of the stiffness center of a machine tool is a major element for knowing the dynamic behavior of this one. This stiffness center can be obtained from a static characterization of the machine tool. For an operation of turning, we present an experimental protocol to determine the stiffness matrix, then by inversion, the associated flexibility matrix. This step makes it possible to establish the privileged directions of the movement associated with the maximum and minimal stiffness as well as the stiffness center. Through this step, it is observed that, at the time of an operation of turning, the movement of the point of the tool is carried out according to an ellipse located in a tilted average plan compared to the machine spindle. This movement is linked with the self-excited vibrations. This analysis could be exploited and transposed in the case of the High Speed Machining. It will make it possible to predict various aspects of machining related to the behavior of the tool in the process of cut.