Cameron Barr
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Cameron Barr has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Milan Brandt
RMIT Centre for Additive Manufacturing, RMIT University, Melbourne, Australia
6 shared publications - Kenong Xia
The University of Melbourne
5 shared publications Shi Da Sun
RMIT Centre for Additive Manufacturing 1 , 58 Cardigan St., Carlton, VIC 3083, Australia
4 shared publications- Andrey Molotnikov
School of Engineering, RMIT University, Melbourne, Australia
2 shared publications Daniel T. McDonald
University of Melbourne
2 shared publications- Ethan Haberl
School of Engineering, RMIT University, Melbourne, Australia
2 shared publications
Latest Publications
- Open Access
- 12 March 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (4) , 4577-4578
Correction: Manufacturability of nickel aluminium bronze lattice struts via digital metal droplet wire arc additive manufacturing
- 12 March 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (4) , 4577-4578
Open AccessCorrection: Manufacturability of nickel aluminium bronze lattice struts via digital metal droplet wire arc additive manufacturing
- 8 January 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (2) , 1931-1945
Manufacturability of nickel aluminium bronze lattice struts via digital metal droplet wire arc additive manufacturing
- 8 January 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (2) , 1931-1945
Manufacturability of nickel aluminium bronze lattice struts via digital metal droplet wire arc additive manufacturing
- 3 November 2023
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 127 (1318) , 2118-2124
Effect of oxygen shielding on the tensile and fatigue performance of 300M repaired through laser-directed energy deposition
Laser-directed energy deposition (L-DED) is a key enabling technology for the repair of high-value aerospace components, as damaged regions can be removed and replaced with additively deposited material. While L-DED repair improves strength and fatigue performance compared to conventional subtractive techniques, mechanical performance can be limited by process-related defects. To assess the role of oxygen on defect formation, local and chamber-based shielding methods were applied in the repair of 300M high strength steel. Oxidation between layers for locally shielded specimens is confirmed to cause large gas pores which have deleterious effects on fatigue life. Such pores are eliminated for chamber shielded specimens, resulting in an increased ductility of ∼15%, compared to ∼11% with chamber shielding. Despite this, unmelted powder defects are not affected by oxygen content and are found in both chamber- and locally shielded samples, which still have negative consequences for fatigue.
- 3 November 2023
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 127 (1318) , 2118-2124
Effect of oxygen shielding on the tensile and fatigue performance of 300M repaired through laser-directed energy deposition
Laser-directed energy deposition (L-DED) is a key enabling technology for the repair of high-value aerospace components, as damaged regions can be removed and replaced with additively deposited material. While L-DED repair improves strength and fatigue performance compared to conventional subtractive techniques, mechanical performance can be limited by process-related defects. To assess the role of oxygen on defect formation, local and chamber-based shielding methods were applied in the repair of 300M high strength steel. Oxidation between layers for locally shielded specimens is confirmed to cause large gas pores which have deleterious effects on fatigue life. Such pores are eliminated for chamber shielded specimens, resulting in an increased ductility of ∼15%, compared to ∼11% with chamber shielding. Despite this, unmelted powder defects are not affected by oxygen content and are found in both chamber- and locally shielded samples, which still have negative consequences for fatigue.
- Open Access
- 28 March 2023
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 35 (2) , 022015
Examination of steel compatibility with additive manufacturing and repair via laser directed energy deposition
High strength steels are a vital material for aerospace applications but are also prone to damage from fatigue, corrosion, and wear. Additive manufacturing (AM) processes such as laser directed energy deposition (L-DED) offer a means for repairing both the geometry and structure of damaged steels; however, significant variation in tensile properties have been reported following repair. While previous studies have tried to improve performance through postdeposition heat treatment, such practices may not be possible for commercial parts due to risks of distortion and thermal damage to the substrate. Instead, this investigation analyses the role of the intrinsic heat treatment effect on as-deposited tensile properties through a detailed review of both AM and AM repair literature. By assessing a wide variety of high strength steels, the links between conventional heat treatment parameters and steel performance in AM are established, and the role of steel composition understood. This review is supported by additional AM and L-DED repaired samples, with consistent parameters used between steels to ensure similar thermal histories, and eliminate potential discrepancies seen between AM machines. The results demonstrate the effect of intrinsic heat treatment on martensitic and precipitation hardening steels, the role of residual heat and heat extraction through the substrate, and flag potential issues faced by steels at risk of temper embrittlement. Taken together, these findings provide a clear vision for the advancement of AM repair and the optimization of mechanical performance.
- 28 March 2023
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 35 (2) , 022015
Open AccessExamination of steel compatibility with additive manufacturing and repair via laser directed energy deposition
High strength steels are a vital material for aerospace applications but are also prone to damage from fatigue, corrosion, and wear. Additive manufacturing (AM) processes such as laser directed energy deposition (L-DED) offer a means for repairing both the geometry and structure of damaged steels; however, significant variation in tensile properties have been reported following repair. While previous studies have tried to improve performance through postdeposition heat treatment, such practices may not be possible for commercial parts due to risks of distortion and thermal damage to the substrate. Instead, this investigation analyses the role of the intrinsic heat treatment effect on as-deposited tensile properties through a detailed review of both AM and AM repair literature. By assessing a wide variety of high strength steels, the links between conventional heat treatment parameters and steel performance in AM are established, and the role of steel composition understood. This review is supported by additional AM and L-DED repaired samples, with consistent parameters used between steels to ensure similar thermal histories, and eliminate potential discrepancies seen between AM machines. The results demonstrate the effect of intrinsic heat treatment on martensitic and precipitation hardening steels, the role of residual heat and heat extraction through the substrate, and flag potential issues faced by steels at risk of temper embrittlement. Taken together, these findings provide a clear vision for the advancement of AM repair and the optimization of mechanical performance.
- 1 May 2020
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 32 (2) , 022061
Influence of fill thickness on tensile perfomance of 300M high strength steel following laser metal deposition repair
Laser metal deposition (LMD) presents a novel method for the repair of high value aerospace components as cracked or wear damaged areas may be locally removed and replaced with fresh materials. To better understand the influence of the extent of repair on mechanical performance, tensile specimens of 300M high strength steel were repaired using LMD to account for 10%, 20%, and 40% of the total cross section depth, with 420SS used as the feed material. LMD repair provided significant improvements to strength compared to the grind-out condition, with greater benefit for larger fill thicknesses. The repaired ultimate tensile strength (UTS) decreased from 1900 to 1750 MPa as the fill thickness increased from 10% to 40%. This was in line with the increasing proportion of 420SS, as this steel has a lower UTS (1360 Mpa) compared to 300M (2000 MPa), with the repaired samples showing typical composite behavior. Brittle martensite in the upper layers of the deposit caused ductility to drop from 13% to below 3% following repair. In situ tempering eliminates untempered martensite in the heat-affected zone and lower layers of the deposit, with hardness in the tempered region ranging from 425 to 550 HV, compared to 600 HV in the substrate and 650 HV in the untempered region. The softest regions of the deposit have the greatest influence over the yield strength, while the UTS is governed by the average strength over the entire region.
- 1 May 2020
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 32 (2) , 022061
Influence of fill thickness on tensile perfomance of 300M high strength steel following laser metal deposition repair
Laser metal deposition (LMD) presents a novel method for the repair of high value aerospace components as cracked or wear damaged areas may be locally removed and replaced with fresh materials. To better understand the influence of the extent of repair on mechanical performance, tensile specimens of 300M high strength steel were repaired using LMD to account for 10%, 20%, and 40% of the total cross section depth, with 420SS used as the feed material. LMD repair provided significant improvements to strength compared to the grind-out condition, with greater benefit for larger fill thicknesses. The repaired ultimate tensile strength (UTS) decreased from 1900 to 1750 MPa as the fill thickness increased from 10% to 40%. This was in line with the increasing proportion of 420SS, as this steel has a lower UTS (1360 Mpa) compared to 300M (2000 MPa), with the repaired samples showing typical composite behavior. Brittle martensite in the upper layers of the deposit caused ductility to drop from 13% to below 3% following repair. In situ tempering eliminates untempered martensite in the heat-affected zone and lower layers of the deposit, with hardness in the tempered region ranging from 425 to 550 HV, compared to 600 HV in the substrate and 650 HV in the untempered region. The softest regions of the deposit have the greatest influence over the yield strength, while the UTS is governed by the average strength over the entire region.
- 13 June 2018
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 30 (3) , 032502
In situ control of tempered martensite during laser cladding repair of aero-grade 300M steel using AISI 420 stainless steel powder
The aim of this paper was to investigate the effect of delay time between the clad tracks on the microstructure hardness evolution. AISI 420 stainless steel was deposited onto 300M steel substrate using a fiber delivered disk laser and a powder blown coaxial nozzle. The delay between the clad tracks was aimed at controlling the in situ quench and tempering sequence during the cladding process. Four different delay times were investigated (continuous build, t = 2 s, t = 5 s, and t = 60 s). No micro-cracking and very little porosity were observed for all variables. The microstructure changed from untempered martensite structure at a continuous build to a fully tempered martensite structure at t = 60 s. The delay time between the clad tracks is the most influential parameter to control the in situ tempering and is crucial to restore the tensile and fatigue properties of aero-grade high strength steel for repair applications.
- 13 June 2018
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 30 (3) , 032502
In situ control of tempered martensite during laser cladding repair of aero-grade 300M steel using AISI 420 stainless steel powder
The aim of this paper was to investigate the effect of delay time between the clad tracks on the microstructure hardness evolution. AISI 420 stainless steel was deposited onto 300M steel substrate using a fiber delivered disk laser and a powder blown coaxial nozzle. The delay between the clad tracks was aimed at controlling the in situ quench and tempering sequence during the cladding process. Four different delay times were investigated (continuous build, t = 2 s, t = 5 s, and t = 60 s). No micro-cracking and very little porosity were observed for all variables. The microstructure changed from untempered martensite structure at a continuous build to a fully tempered martensite structure at t = 60 s. The delay time between the clad tracks is the most influential parameter to control the in situ tempering and is crucial to restore the tensile and fatigue properties of aero-grade high strength steel for repair applications.
- 1 April 2018
- Published by Elsevier in Surface and Coatings Technology
- Vol. 340, 126-136
Influence of macrosegregation on solidification cracking in laser clad ultra-high strength steels
- 1 April 2018
- Published by Elsevier in Surface and Coatings Technology
- Vol. 340, 126-136
Influence of macrosegregation on solidification cracking in laser clad ultra-high strength steels