Lu-Jun Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lu-Jun Huang has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Lin Geng
State Key Laboratory of Precision Welding and Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
3 shared publications Aibin Li
National Key Laboratory of Science and Technology on Precision Heat Processing of Metals Harbin Institute of Technology 150001 Harbin China
1 shared publication- Baoxi Liu
Hebei university of Technology
1 shared publication Ce Liang
School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China
1 shared publicationFeng Li
School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China
1 shared publicationFuyao Yang
National Key Laboratory of Science and Technology on Precision Heat Processing of Metals Harbin Institute of Technology 150001 Harbin China
1 shared publication
Latest Publications
- 1 January 2013
- Published by China Science Publishing & Media Ltd. in ACTA METALLURGICA SINICA
- Vol. 49 (9) , 1131
EFFECTS OF Cu CONTENT ON THE WEAR PROPERTIESOF A1203}Si02sf/Al-Cu COMPOSITES
- 1 January 2013
- Published by China Science Publishing & Media Ltd. in ACTA METALLURGICA SINICA
- Vol. 49 (9) , 1131
EFFECTS OF Cu CONTENT ON THE WEAR PROPERTIESOF A1203}Si02sf/Al-Cu COMPOSITES
- 1 December 2012
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 22, s465-s471
Hot deformation behavior of in-situ TiBw/Ti6Al4V composite with novel network reinforcement distribution
- 1 December 2012
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 22, s465-s471
Hot deformation behavior of in-situ TiBw/Ti6Al4V composite with novel network reinforcement distribution
- 1 August 2011
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 21, s358-s361
Fabrication of Ti-Al complex with superior deformation capability by pressure infiltration
- 1 August 2011
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 21, s358-s361
Fabrication of Ti-Al complex with superior deformation capability by pressure infiltration
- 1 March 2011
- Published by Wiley in Rare Metals
- Vol. 30 (S1) , 614-618
Study on the fabrication and heat treatment of the sheet material of in situ TiBw/Ti60 composites
5 vol.% TiB whiskers (TiBw) reinforced Ti60 composites (TiBw/Ti60) with a novel network microstructure have been successfully fabricated by reaction hot pressing, and then the composite sheets can be obtained by subsequently rolling deformation at 1040 °C. In order to further improve a combination of properties of the composite sheets, the as‐rolled composite sheets have been heat treated by different parameters. The results show that the matrix of the as‐sintered TiBw/Ti60 composite exhibits platelet or equiaxed alpha phase and intergranular beta phase, and the ultimate strength of the composite is significantly improved compared with that of the monolithic Ti60 alloy. However, undergoing rolling deformation and solution treatment, the alpha phase in the matrix becomes fine and equiaxed, and the ultimate strength of the composites is significantly increased to 1379 MPa along with 4.1% of elongation. In addition, a superior combination of properties can be achieved by the heat treatment of 950 °C / 0.5 h / WQ + 500 °C / 2 h / AC.
- 1 March 2011
- Published by Wiley in Rare Metals
- Vol. 30 (S1) , 614-618
Study on the fabrication and heat treatment of the sheet material of in situ TiBw/Ti60 composites
5 vol.% TiB whiskers (TiBw) reinforced Ti60 composites (TiBw/Ti60) with a novel network microstructure have been successfully fabricated by reaction hot pressing, and then the composite sheets can be obtained by subsequently rolling deformation at 1040 °C. In order to further improve a combination of properties of the composite sheets, the as‐rolled composite sheets have been heat treated by different parameters. The results show that the matrix of the as‐sintered TiBw/Ti60 composite exhibits platelet or equiaxed alpha phase and intergranular beta phase, and the ultimate strength of the composite is significantly improved compared with that of the monolithic Ti60 alloy. However, undergoing rolling deformation and solution treatment, the alpha phase in the matrix becomes fine and equiaxed, and the ultimate strength of the composites is significantly increased to 1379 MPa along with 4.1% of elongation. In addition, a superior combination of properties can be achieved by the heat treatment of 950 °C / 0.5 h / WQ + 500 °C / 2 h / AC.