Sampan Rittidech

This study aimed to investigate the application of a Heart Shaped Glass Spoon Loop Oscillating Heat Pipe (HSGS/LOHP) made of a glass tube. The results showed that HSGS/LOHP can be practically used for stirring hot coffee in a cup. At the working substance filling rates of 80 and 60%, slug and annular flows of the working substance pattern were found while at 40% only the slug flow was found. The maximum mean lengths of the slug and annular flows of the working substance were 0.0259 and 0.00443 m which occurred at the working substance filling rate of 80% at the evaporator temperatures of 40℃, the average velocity was the highest for every working substance filling rate at the evaporator temperatures 70°C. The slug and annular flow patterns had maximum speeds of 0.00171 and 0.00111 m/s when tested at the 40% and 60% working substance filling rates, respectively. The working substance at the evaporator temperature of 40℃ and the filling rate of 80% had the highest buoyancy force and moment of inertia of 4.90 ± 0.25 kN and 901.77 ± 45.08 Tm2·kg, respectively.

This research presents a case study of applying a loop thermosyphon with a vapor chamber (LTVC) for a chilli oven (O/LTVC). The LTVC had a dimension evaporator chamber size of 200 mm × 200 mm ×75 mm...

In this article, an optimization technique using the Taguchi method with multiple performance characteristics for the percent zinc coating balances edge joints of galvanized steel sheets for metal inert gas pulse brazing process was proposed. The orthogonal array, multi-response signal-to-noise ratio, and analysis of variance were employed to study the performance characteristics. Five metal inert gas pulse brazing process parameters, namely, wire feed speed, arc voltages, travel speed, peak currents, and pulse frequency, were optimized with considerations of multiple performance characteristics including percent zinc coating balances edge joints. Experimental results were provided to confirm the effectiveness of this approach. The optimum metal inert gas pulse brazing technique conditions were wire feed speed of 3.25 m/min, arc voltages of 18 V, travel speed of 0.8 m/min, peak currents of 425 A, and pulse frequency of 35 Hz. Confirmation tests of the optimal levels with the initial cutting parameters are carried out in order to illustrate the effectiveness of this method in metal inert gas pulse brazing technique for galvanized steel sheets.

This research is aimed at studying the two-phase flow pattern of a top heat mode closed loop oscillating heat pipe with check valves. The working fluids used are ethanol and R141b and R11 coolants with a filling ratio of 50% of the total volume. It is found that the maximum heat flux occurs for the R11 coolant used as the working fluid in the case with the inner diameter of 1.8 mm, inclination angle of −90◦, evaporator temperature of 125◦C, and evaporator length of 50 mm. The internal flow patterns are found to be slug flow/disperse bubble flow/annular flow, slug flow/disperse bubble flow/churn flow, slug flow/bubble flow/annular flow, slug flow/disperse bubble flow, bubble flow/annular flow, and slug flow/annular flow.

The objective of this work was to optimize the percent zinc coating balances edge joints of galvanized steel sheets using the metal inert gas pulse brazing process. The Taguchi method and grey relational analysis were used to determine the relationship between the metal inert gas pulse brazing process parameters and percent zinc coating balances edge joints. The metal inert gas pulse brazing process parameters used in this study included wire feed speeds, arc voltages, travel speed, peak currents, and pulse frequency. The characteristics of metal inert gas pulse brazing process that were considered to find response were percent zinc coating balances edge joints on the upper edge joint (PZBEJ1), the lower edge joint (PZBEJ2), and the back sides of the edge joint (PZBEJ3). Analysis of variance was performed to determine the impact of an individual process parameter on the quality parameters. The results showed that the optimal parameters in which grey relational grade increases at the highest level were wire feed speeds at 3.25 m/min, arc voltages at 16 V, travel speeds at 0.9 m/min, peak currents at 425 A, and pulse frequency at 35 Hz. These parameters gave a 74.90% higher response value than those of the initial parameters of metal inert gas pulse brazing process.

The aim of this study was to perform life testing and determine the effect of working fluid on the corrosion of a heat pipe with a sintered wick. The heat pipe was made from a copper tube. The inner heat pipe was filled with 99.97% pure copper powder as a dendritic for the sintering process. The heat pipe had an outer diameter of 6 mm with a length of 200 mm, and distilled water and ethanol were the working fluids. The operating temperature at the evaporator was 125°C. The analysis consisted of using a scanning electron microscope, energy dispersive X-ray spectrometry and atomic absorption spectroscopy. The results of the scanning electron microscope and energy dispersive X-ray spectrometry analysis showed that the corrosion of the heat pipe was uniform. The result of the atomic absorption spectroscopy indicated that the concentration of the copper in the ethanol as the working fluid was greater than in the distilled water as the working fluid, and the highest concentration of copper particles in the ethanol was 22.7499 ppm or 0.0409 mg after testing for 3000 h. The concentration of copper was higher when the length of the life test increased due to corrosion of the heat pipe.