Rahul A. Bidkar
Rahul A. Bidkar has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Daniel A. McAdams
Fellow ASME Department of Mechanical Engineering, Texas A&M University, College Station, TX 77840
2 shared publications - Aaron M. Rimpel
Southwest Research Institute , 6220 Culebra Road, San Antonio, TX 78238
1 shared publication Andrew Mann
General Electric Global Research, Niskayuna, NY 12309
1 shared publicationAzam M. Thatte
General Electric Global Research, Niskayuna, NY 12309
1 shared publication- Collin Rambacher
GE Aerospace Research , 1 Research Circle, Niskayuna, NY 12309
1 shared publication - Deepak Trivedi
GE Aerospace Research , 1 Research Circle, Niskayuna, NY 12309
1 shared publication
Latest Publications
- 20 November 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (2) , 1-38
Development of Large-Diameter Hybrid Film-Riding Seals for Supercritical Carbon Dioxide Turbines
Compared to traditional labyrinth seals, film-riding face seals are worth 0.55-0.65% points efficiency for utility-scale supercritical carbon dioxide (sCO2) turbines. Conventional dry gas seals (DGS) cannot be used at such large diameters due to manufacturability limitations as well as mechanical deformations. Hybrid film-riding face seals are excellent compromise candidates that can operate at large diameters with slightly increased albeit leakier films. This paper presents the development and test data for a hybrid face seal developed for the utility-scale sCO2 turbine application. A high-level overview of the seal design considerations is presented followed by test data on three seals – a small-size seal (5.7 in diameter), an intermediate-size seal (14-in diameter) and two full-size seals (24 in diameter) tested over a range of pressures and temperatures with both air and CO2 as the working fluid. This paper presents non-dimensional seal film thickness and seal leakage (effective clearance) data as a function of the pressure ratios, speed and temperature. The film thickness measurements presented in this paper agree well with the CFD-based film thickness predictions. The measured seal effective clearance for the seals was around 0.001 in (0.0254 mm) effective clearance, which is better than published data on aerostatic face seals and less risky compared to traditional DGS. Rotating test data across all three length scales presented in this work show successful laboratory-scale seal operation for the newly-design hybrid face seals.
- 20 November 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (2) , 1-38
Development of Large-Diameter Hybrid Film-Riding Seals for Supercritical Carbon Dioxide Turbines
Compared to traditional labyrinth seals, film-riding face seals are worth 0.55-0.65% points efficiency for utility-scale supercritical carbon dioxide (sCO2) turbines. Conventional dry gas seals (DGS) cannot be used at such large diameters due to manufacturability limitations as well as mechanical deformations. Hybrid film-riding face seals are excellent compromise candidates that can operate at large diameters with slightly increased albeit leakier films. This paper presents the development and test data for a hybrid face seal developed for the utility-scale sCO2 turbine application. A high-level overview of the seal design considerations is presented followed by test data on three seals – a small-size seal (5.7 in diameter), an intermediate-size seal (14-in diameter) and two full-size seals (24 in diameter) tested over a range of pressures and temperatures with both air and CO2 as the working fluid. This paper presents non-dimensional seal film thickness and seal leakage (effective clearance) data as a function of the pressure ratios, speed and temperature. The film thickness measurements presented in this paper agree well with the CFD-based film thickness predictions. The measured seal effective clearance for the seals was around 0.001 in (0.0254 mm) effective clearance, which is better than published data on aerostatic face seals and less risky compared to traditional DGS. Rotating test data across all three length scales presented in this work show successful laboratory-scale seal operation for the newly-design hybrid face seals.
- Open Access
- 13 September 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (2)
Low-Leakage Shaft-End Seals for Utility-Scale Supercritical CO2 Turboexpanders
Supercritical carbon dioxide (sCO2) power cycles could be a more efficient alternative to steam Rankine cycles for power generation from coal. Using existing labyrinth seal technology, shaft-end-seal leakage can result in a 0.55–0.65% points efficiency loss for a nominally 500 MWe sCO2 power cycle plant. Low-leakage hydrodynamic face seals are capable of reducing this leakage loss and are considered a key enabling component technology for achieving 50–52% thermodynamic cycle efficiencies with indirect coal-fired sCO2 power cycles. In this paper, a hydrodynamic face seal concept is presented for utility-scale sCO2 turbines. A 3D computational fluid dynamics (CFD) model with real gas CO2 properties is developed for studying the thin-film physics. These CFD results are also compared with the predictions of a Reynolds-equation-based solver. The 3D CFD model results show large viscous shear and the associated windage heating challenge in sCO2 face seals. Following the CFD model, an axisymmetric finite-element analysis (FEA) model is developed for parametric optimization of the face seal cross section with the goal of minimizing the coning of the stationary ring. A preliminary thermal analysis of the seal is also presented. The fluid, structural, and thermal results show that large-diameter (about 24 in.) face seals with small coning (of the order of 0.0005 in.) are possible. The fluid, structural, and thermal results are used to highlight the design challenges in developing face seals for utility-scale sCO2 turbines.
- 13 September 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (2)
Open AccessLow-Leakage Shaft-End Seals for Utility-Scale Supercritical CO2 Turboexpanders
Supercritical carbon dioxide (sCO2) power cycles could be a more efficient alternative to steam Rankine cycles for power generation from coal. Using existing labyrinth seal technology, shaft-end-seal leakage can result in a 0.55–0.65% points efficiency loss for a nominally 500 MWe sCO2 power cycle plant. Low-leakage hydrodynamic face seals are capable of reducing this leakage loss and are considered a key enabling component technology for achieving 50–52% thermodynamic cycle efficiencies with indirect coal-fired sCO2 power cycles. In this paper, a hydrodynamic face seal concept is presented for utility-scale sCO2 turbines. A 3D computational fluid dynamics (CFD) model with real gas CO2 properties is developed for studying the thin-film physics. These CFD results are also compared with the predictions of a Reynolds-equation-based solver. The 3D CFD model results show large viscous shear and the associated windage heating challenge in sCO2 face seals. Following the CFD model, an axisymmetric finite-element analysis (FEA) model is developed for parametric optimization of the face seal cross section with the goal of minimizing the coning of the stationary ring. A preliminary thermal analysis of the seal is also presented. The fluid, structural, and thermal results show that large-diameter (about 24 in.) face seals with small coning (of the order of 0.0005 in.) are possible. The fluid, structural, and thermal results are used to highlight the design challenges in developing face seals for utility-scale sCO2 turbines.
- 7 July 2009
- Published by Springer Nature in Research in Engineering Design
- Vol. 21 (1) , 1-24
Methods for automated manufacturability analysis of injection-molded and die-cast parts
- 7 July 2009
- Published by Springer Nature in Research in Engineering Design
- Vol. 21 (1) , 1-24
Methods for automated manufacturability analysis of injection-molded and die-cast parts
- 1 January 2003
- Published by ASME International
- p. 205-226
Automated Manufacturability Analysis for Injection-Molded and Die-Cast Parts
In this article, a mathematical framework to automatically evaluate the manufacturability of injection-molded and die-cast parts is presented. The framework includes both a logical algorithm for the general problem of feature recognition and an implemented mathematical and numerical algorithm to solve key outstanding challenges in feature recognition for manufacturability analysis. A novel feature recognition method is developed that is based on decomposing the part into elemental cubes and then, making use of their individual manufacturability, the manufacturability of the part as a whole is evaluated. This article discusses a procedure to obtain a 3D binary representation of the solid model in a simple fashion and further develops feature recognition techniques to extract critical manufacturability information from this 3D binary array. The outstanding challenges addressed by the method presented include the finding of parting surfaces, undercuts, holes, and bosses in the context of an injection-molded or diecast part. The algorithm is implemented using a combination of C++ code and Unigraphics solid modeling software. A short example is presented.
- 1 January 2003
- Published by ASME International
- p. 205-226
Automated Manufacturability Analysis for Injection-Molded and Die-Cast Parts
In this article, a mathematical framework to automatically evaluate the manufacturability of injection-molded and die-cast parts is presented. The framework includes both a logical algorithm for the general problem of feature recognition and an implemented mathematical and numerical algorithm to solve key outstanding challenges in feature recognition for manufacturability analysis. A novel feature recognition method is developed that is based on decomposing the part into elemental cubes and then, making use of their individual manufacturability, the manufacturability of the part as a whole is evaluated. This article discusses a procedure to obtain a 3D binary representation of the solid model in a simple fashion and further develops feature recognition techniques to extract critical manufacturability information from this 3D binary array. The outstanding challenges addressed by the method presented include the finding of parting surfaces, undercuts, holes, and bosses in the context of an injection-molded or diecast part. The algorithm is implemented using a combination of C++ code and Unigraphics solid modeling software. A short example is presented.