ARAaron M. Rimpel

Aaron M. Rimpel

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Aaron M. Rimpel has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Development of Large-Diameter Hybrid Film-Riding Seals for Supercritical Carbon Dioxide Turbines

    by Rahul A. Bidkar, Uttara Kumar, Deepak Trivedi, Xiaohua Zhang, Collin Rambacher, Aaron Rimpel, Thomas Kerr, Jeremy Johnson

    Compared to traditional labyrinth seals, film-riding face seals are worth 0.55-0.65% points efficiency for utility-scale supercritical carbon dioxide (sCO2) turbines. Conventional dry gas seals (DGS) cannot be used at such large diameters due to manufacturability limitations as well as mechanical deformations. Hybrid film-riding face seals are excellent compromise candidates that can operate at large diameters with slightly increased albeit leakier films. This paper presents the development and test data for a hybrid face seal developed for the utility-scale sCO2 turbine application. A high-level overview of the seal design considerations is presented followed by test data on three seals – a small-size seal (5.7 in diameter), an intermediate-size seal (14-in diameter) and two full-size seals (24 in diameter) tested over a range of pressures and temperatures with both air and CO2 as the working fluid. This paper presents non-dimensional seal film thickness and seal leakage (effective clearance) data as a function of the pressure ratios, speed and temperature. The film thickness measurements presented in this paper agree well with the CFD-based film thickness predictions. The measured seal effective clearance for the seals was around 0.001 in (0.0254 mm) effective clearance, which is better than published data on aerostatic face seals and less risky compared to traditional DGS. Rotating test data across all three length scales presented in this work show successful laboratory-scale seal operation for the newly-design hybrid face seals.

  • Simple Contact Stiffness Model Validation for Tie Bolt Rotor Design With Butt Joints and Pilot Fits

    by Aaron M. Rimpel, Matthew Leopard

    Tie bolt rotors for centrifugal compressors comprise multiple shaft components that are held together by a single tie bolt. The axial connections of these rotors—including butt joints, Hirth couplings, and Curvic couplings—exhibit a contact stiffness effect, which tends to lower the shaft bending frequencies compared to geometrically identical monolithic shafts. If not accounted for in the design stage, shaft bending critical speed margins can be compromised after a rotor is built. A previous paper had investigated the effect of tie bolt force on the bending stiffness of stacked rotor assemblies with butt joint interfaces, both with and without pilot fits. This previous work derived an empirical contact stiffness model and developed a practical finite element modeling approach for simulating the axial contact surfaces, which was validated by predicting natural frequencies for several test rotor configurations. The present work built on these previous results by implementing the same contact stiffness modeling approach on a real tie bolt rotor system designed for a high pressure centrifugal compressor application. Each joint location included two axial contact faces, with contact pressures up to five times higher than previously modeled, and a locating pilot fit. The free-free natural frequencies for different amounts of tie bolt preload force were measured, and the frequencies exhibited the expected stiffening behavior with increasing preload. However, a discontinuity in the data trend indicated a step-change increase in the contact stiffness. It was shown that this was likely due to one or more of the contact faces becoming fully engaged only after sufficient tie bolt force was applied. Finally, a design calculation was presented that can be used to estimate whether contact stiffness effects may be ignored, which could simplify rotor analyses if adequate contact pressure is used.


  • Impact of Bearing Clearance on Measured Stiffness and Damping Coefficients and Thermal Performance of a High-Stiffness Generation 3 Foil Journal Bearing

    by Jason C. Wilkes, Jonathan Wade, Aaron Rimpel, Jeff Moore, Erik Swanson, Joseph Grieco, Jerry Brady

    High-speed foil bearings are currently used in increasingly demanding, high performance applications. The application under consideration is a 120 krpm natural gas turboexpander-compressor, which requires 38 mm (1.5 in.) foil journal bearings with high stiffness and load capacity to help enhance rotordynamic stability. This paper describes the development of the foil bearing for this application and includes measured stiffness and damping coefficients recorded on a high-speed dynamic bearing test rig. The dynamic test data were taken for several different foil bearing configurations with varying spring-element foil thicknesses, number of spring-element foils, and bearing shim thickness. All three parameters have a direct impact on bearing clearance. The influence of these different parameters on measured stiffness and damping coefficients and thermal performance of the bearings are presented and discussed.


  • A Rotordynamic, Thermal, and Thrust Load Performance Gas Bearing Test Rig and Test Results for Tilting Pad Journal Bearings and Spiral Groove Thrust Bearings

    by Aaron M. Rimpel, Giuseppe Vannini, Jongsoo Kim

    A high-speed gas bearing test rig was developed to characterize rotordynamic, thermal, and thrust load performance of gas bearings being developed for an oil-free turboexpander. The radial bearings (RBs) tested in this paper were tilting pad journal bearings with radial compliance features that allow the bearing bore to increase to accommodate shaft growth, and the thrust bearings (TBs) were a spiral groove type with axial compliance features. The TB accounts for over 90% of the combined bearing power consumption, which has a cubic relationship with speed and increases with case pressure. RB circumferential pad temperatures increased approximately with speed to the fourth or fifth power, with slightly higher temperature rise for lower case pressure. Maximum steady-state bearing pad temperatures increase with increasing speed for similar cooling mass flow rates; however, only the TB showed a significant increase in temperature with higher case pressure. The TBs were stable at all speeds, but the load capacity was found to be lower than anticipated, apparently due to pad deformations caused by radial temperature gradients in the stator. More advanced modeling approaches have been proposed to better understand the TB thermal behavior and to improve the TB design. Finally, the RBs tested were demonstrated to be stable up to the design speed of 130 krpm, which represents the highest surface speed for tilting pad gas bearings tested in the literature.