Yosuke Ogino
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yosuke Ogino has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
Satoru Asai
Graduate School of Engineering, Osaka University, Suita, Japan
5 shared publicationsYoshinori Hirata
Graduate School of Engineering, Osaka University, Osaka, Japan
5 shared publicationsS. Asai
Graduate School of Engineering, Osaka University, Osaka, Japan
3 shared publications- Satoru Asai
DAIHEN Welding and Joining Research Alliance Laboratories, Joining and Welding Research Institute, The University of Osaka, Osaka 567-0047, Japan
3 shared publications - Tomokazu Sano
Graduate School of Engineering, Osaka University, Suita, Japan
3 shared publications Y. Hirata
Graduate School of Engineering, Osaka University, Suita, Japan
3 shared publications
Latest Publications
- Open Access
- 20 August 2024
- Published by Springer Nature in Communications Materials
- Vol. 5 (1) , 1-9
In-situ X-ray imaging of the breakup dynamics of current-carrying molten metal jets during arc discharge
- 20 August 2024
- Published by Springer Nature in Communications Materials
- Vol. 5 (1) , 1-9
Open AccessIn-situ X-ray imaging of the breakup dynamics of current-carrying molten metal jets during arc discharge
- Open Access
- 13 March 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (9) , 2271-2279
Visualization and control of the free-flight transfer phenomenon in the wire feed control process
Gas metal arc (GMA) welding requires improved process stability, higher quality and efficiency, and quantitative control of the heat input and deposition. These requirements can be achieved by appropriately controlling the metal transfer phenomenon. However, this control method has primarily been applied to short-circuit transfer, and very few examples of its application to free-flight transfer exist. Therefore, the effect of wire feed control on free-flight transfer remains unclear. In this study, the influence of wire feed control on the free-flight transfer phenomenon in the GMA welding process using an aluminum wire electrode was investigated through experimental observations, and free-flight transfer control was attempted.It was observed the free-flight transfer phenomenon, particularly globular transfer, under low-current conditions with controlled wire feeding under various feed conditions, using wire feed–retract speeds and cycles as parameters. The observation results revealed two patterns with different timings of droplet detachment under long- and short-period conditions. Furthermore, the observation of the droplet detachment motions revealed that the inertia caused by the acceleration or deceleration of the feed speed acts on the droplet. Moreover, the difference between the two transfer patterns is primarily caused by the inertia acting on the droplet before and after switching the wire feed–retract direction and the size of the droplet at that time. Based on this, free-flight transfer can be stabilized by reconfiguring the feed conditions.
- 13 March 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (9) , 2271-2279
Open AccessVisualization and control of the free-flight transfer phenomenon in the wire feed control process
Gas metal arc (GMA) welding requires improved process stability, higher quality and efficiency, and quantitative control of the heat input and deposition. These requirements can be achieved by appropriately controlling the metal transfer phenomenon. However, this control method has primarily been applied to short-circuit transfer, and very few examples of its application to free-flight transfer exist. Therefore, the effect of wire feed control on free-flight transfer remains unclear. In this study, the influence of wire feed control on the free-flight transfer phenomenon in the GMA welding process using an aluminum wire electrode was investigated through experimental observations, and free-flight transfer control was attempted.It was observed the free-flight transfer phenomenon, particularly globular transfer, under low-current conditions with controlled wire feeding under various feed conditions, using wire feed–retract speeds and cycles as parameters. The observation results revealed two patterns with different timings of droplet detachment under long- and short-period conditions. Furthermore, the observation of the droplet detachment motions revealed that the inertia caused by the acceleration or deceleration of the feed speed acts on the droplet. Moreover, the difference between the two transfer patterns is primarily caused by the inertia acting on the droplet before and after switching the wire feed–retract direction and the size of the droplet at that time. Based on this, free-flight transfer can be stabilized by reconfiguring the feed conditions.
- Open Access
- 15 January 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (4) , 905-913
Process parameters and their effect on metal transfer in gas metal arc welding: a driving force perspective
In gas metal arc welding (GMAW), the optimization of process parameters and the control of metal transfer is pivotal for achieving superior welding outcomes. This study meticulously examines the roles of core process parameters in metal transfer: wire extension and arc geometry, which includes arc length and inter-cathode distance. Using a unique MIG-based non-transferred arc system with symmetrically arranged tungsten cathodes we have achieved distinct control over wire feed rate and arc geometry, independent of the arc current. We investigate the interplay of these parameters and their consequential influence on the driving forces governing metal transfer. While increasing the wire extension enhanced inertial forces, it did not lead to consistent transitions in the metal transfer modes. In contrast, adjusting arc length and inter-cathode distance effectively controlled the electromagnetic force acting on molten droplets, as quantified by the arc spread angle $$\theta$$ . Notably, an increase in the arc spread angle resulted in the elongation of molten droplets. This study clarifies the fundamental relationships between driving forces and process parameters in GMAW. Additionally, it introduces a more advanced evaluation model for electromagnetic force and offers a comprehensive strategy for refining welding control techniques.- 15 January 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (4) , 905-913
Open AccessProcess parameters and their effect on metal transfer in gas metal arc welding: a driving force perspective
In gas metal arc welding (GMAW), the optimization of process parameters and the control of metal transfer is pivotal for achieving superior welding outcomes. This study meticulously examines the roles of core process parameters in metal transfer: wire extension and arc geometry, which includes arc length and inter-cathode distance. Using a unique MIG-based non-transferred arc system with symmetrically arranged tungsten cathodes we have achieved distinct control over wire feed rate and arc geometry, independent of the arc current. We investigate the interplay of these parameters and their consequential influence on the driving forces governing metal transfer. While increasing the wire extension enhanced inertial forces, it did not lead to consistent transitions in the metal transfer modes. In contrast, adjusting arc length and inter-cathode distance effectively controlled the electromagnetic force acting on molten droplets, as quantified by the arc spread angle $$\theta$$ . Notably, an increase in the arc spread angle resulted in the elongation of molten droplets. This study clarifies the fundamental relationships between driving forces and process parameters in GMAW. Additionally, it introduces a more advanced evaluation model for electromagnetic force and offers a comprehensive strategy for refining welding control techniques. - 28 April 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (7) , 1381-1393
Development of a simulation model of the manual gas tungsten arc welding process and visualization of the welder’s skill
- 28 April 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (7) , 1381-1393
Development of a simulation model of the manual gas tungsten arc welding process and visualization of the welder’s skill
- 2 June 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (32) , 325204
Non-equilibrium modeling of arc plasmas in the gas–metal arc–welding process
In recent years, the thermal and chemical non-equilibrium properties of arc plasmas have been among the most critical topics in the modeling of welding arcs. Non-equilibrium phenomena can be observed in the near-electrode regions, where the characteristics of the arc are determined. Although non-equilibrium modeling should contribute to a deeper understanding of the gas–metal arc-welding (GMAW) process, no non-equilibrium model has been reported for GMAW processes, while several models have been reported for gas–tungsten arc-welding processes. In this study, we attempted to elucidate the non-equilibrium phenomena in the GMAW process. In addition, as a first step, we developed a non-equilibrium model of the arc plasma in the GMAW process. The influence of the iron vapor was successfully determined by our model. We then inferred that the concentration of iron vapor affects the number density of electrons and, consequently, the thermal equilibrium of the arc in the GMAW process.
- 2 June 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (32) , 325204
Non-equilibrium modeling of arc plasmas in the gas–metal arc–welding process
In recent years, the thermal and chemical non-equilibrium properties of arc plasmas have been among the most critical topics in the modeling of welding arcs. Non-equilibrium phenomena can be observed in the near-electrode regions, where the characteristics of the arc are determined. Although non-equilibrium modeling should contribute to a deeper understanding of the gas–metal arc-welding (GMAW) process, no non-equilibrium model has been reported for GMAW processes, while several models have been reported for gas–tungsten arc-welding processes. In this study, we attempted to elucidate the non-equilibrium phenomena in the GMAW process. In addition, as a first step, we developed a non-equilibrium model of the arc plasma in the GMAW process. The influence of the iron vapor was successfully determined by our model. We then inferred that the concentration of iron vapor affects the number density of electrons and, consequently, the thermal equilibrium of the arc in the GMAW process.
- 20 August 2020
- Published by Springer Nature in Welding in the World
- Vol. 64 (12) , 2011-2017
Three-dimensional numerical model of short-circuiting transfer in GMAW
- 20 August 2020
- Published by Springer Nature in Welding in the World
- Vol. 64 (12) , 2011-2017
Three-dimensional numerical model of short-circuiting transfer in GMAW
- 24 July 2020
- Published by Springer Nature in Welding in the World
- Vol. 64 (11) , 1897-1904
Direct observation and numerical simulation of molten metal and molten slag behavior in electroslag welding process
- 24 July 2020
- Published by Springer Nature in Welding in the World
- Vol. 64 (11) , 1897-1904
Direct observation and numerical simulation of molten metal and molten slag behavior in electroslag welding process
- 14 July 2020
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 40 (5) , 1109-1126
Discussion of the Effect of Shielding Gas and Conductivity of Vapor Core on Metal Transfer Phenomena in Gas Metal Arc Welding by Numerical Simulation
- 14 July 2020
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 40 (5) , 1109-1126
Discussion of the Effect of Shielding Gas and Conductivity of Vapor Core on Metal Transfer Phenomena in Gas Metal Arc Welding by Numerical Simulation
- 13 July 2020
- Published by Springer Nature in Welding in the World
- Vol. 64 (10) , 1789-1797
Visualization of arc plasma and molten wire behavior in CO2 arc welding process by three-dimensional numerical simulation
- 13 July 2020
- Published by Springer Nature in Welding in the World
- Vol. 64 (10) , 1789-1797
Visualization of arc plasma and molten wire behavior in CO2 arc welding process by three-dimensional numerical simulation
- 1 January 2020
- Published by Japan Welding Society in JOURNAL OF THE JAPAN WELDING SOCIETY
- Vol. 89 (5) , 390
Activity Reports of “Establishment of Global Network for Young Engineers and Researchers in the Welding and Joining Fields” at 2019
- 1 January 2020
- Published by Japan Welding Society in JOURNAL OF THE JAPAN WELDING SOCIETY
- Vol. 89 (5) , 390
Activity Reports of “Establishment of Global Network for Young Engineers and Researchers in the Welding and Joining Fields” at 2019