Guolei Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Guolei Zheng has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Min Zhou
College of Engineering, China Agricultural University, Beijing 100083, China
2 shared publications - Yenan Shi
School of Mechanical Engineering and Automation, Beihang University, Beijing, China
2 shared publications - Chunling Zeng
Institute of Technology and Equipment, Chengdu Aircraft Industry (Group) Co. Ltd., Chengdu 610092, China
1 shared publication - Debiao Zeng
Chengdu Aircraft Industrial (Group) Co., Ltd., Chengdu 610092, China
1 shared publication - Huangjin Zhao
School of Mechanical Engineering and Automation, Beijing University of Aeronautics and Astronautics, Beijing 100191, China
1 shared publication - Huangjin Zhao
School of Mechanical Engineering and Automation, Beijing University of Aeronautics and Astronautics, Beijing, China
1 shared publication
Latest Publications
- 12 June 2024
- Published by Springer Nature in Journal of Global Optimization
- Vol. 90 (2) , 487-514
A novel algorithm for finding convex hull of a generic polygon with simulation of progressively supporting elastic lines
- 12 June 2024
- Published by Springer Nature in Journal of Global Optimization
- Vol. 90 (2) , 487-514
A novel algorithm for finding convex hull of a generic polygon with simulation of progressively supporting elastic lines
- Open Access
- 1 April 2023
- Published by China Science Publishing & Media Ltd. in Journal of Computer-Aided Design & Computer Graphics
- Vol. 35 (4) , 609-620
Boundary Point Tracking Method for Surface Iso-Segmentation
The surface iso-segmentation method with conditions as input has applicability to different segmentation situations, however, does not thoroughly investigate its boundary point (BP) tracking procedure. Therefore, we present a BP tracking algorithm for surface iso-segmentation. Firstly, the BP tracking algorithm tracks BPs by repeatedly selecting the in-BP and out-BP of the current grid unit, constructing the subsequent grid unit and setting it as the current grid unit. Secondly, the key techniques of the algorithm including grid unit dynamic construction and the in-BP and out-BP selection of grid units by reasonably predicting the boundary curve (BC) growing trend are then systematically explored. Finally, attributes including coordinate, machinability, normal, Gaussian curvature and mean curvature are used to design 5 condition sets for the iso-segmentation of several CAD surfaces. When each grid unit has only 2 BPs, our method has the same segmentation accuracy with the existing method. When there exists a grid unit which has more than 2 BPs, the average BP deviation of our method is 91.78% lower than that of the existing method. Test results show that the proposed method suits for more complicated segmentation problems, and can achieve more precise segmentation and higher robustness.
- 1 April 2023
- Published by China Science Publishing & Media Ltd. in Journal of Computer-Aided Design & Computer Graphics
- Vol. 35 (4) , 609-620
Open AccessBoundary Point Tracking Method for Surface Iso-Segmentation
The surface iso-segmentation method with conditions as input has applicability to different segmentation situations, however, does not thoroughly investigate its boundary point (BP) tracking procedure. Therefore, we present a BP tracking algorithm for surface iso-segmentation. Firstly, the BP tracking algorithm tracks BPs by repeatedly selecting the in-BP and out-BP of the current grid unit, constructing the subsequent grid unit and setting it as the current grid unit. Secondly, the key techniques of the algorithm including grid unit dynamic construction and the in-BP and out-BP selection of grid units by reasonably predicting the boundary curve (BC) growing trend are then systematically explored. Finally, attributes including coordinate, machinability, normal, Gaussian curvature and mean curvature are used to design 5 condition sets for the iso-segmentation of several CAD surfaces. When each grid unit has only 2 BPs, our method has the same segmentation accuracy with the existing method. When there exists a grid unit which has more than 2 BPs, the average BP deviation of our method is 91.78% lower than that of the existing method. Test results show that the proposed method suits for more complicated segmentation problems, and can achieve more precise segmentation and higher robustness.
- 17 April 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 46 (9) , 8617-8628
Structural Self-Similarity Framework for Virtual Human’s Whole Posture Generation
- 17 April 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 46 (9) , 8617-8628
Structural Self-Similarity Framework for Virtual Human’s Whole Posture Generation
- 24 June 2019
- Published by U-turn Press LLC
A Visual-cognition-inspired Model for Machining Feature Recognition
Artificial neural network (ANN) is a successful implementation of imitating biological neural network. Feature recognition is a key technology in CAD/CAM. Using ANN to identify machining features is a significant interdisciplinary research direction of feature recognition, and has received considerable results. The method mainly performs pre-processing and assigns features based on B-rep information or voxel representation, and then inputs them into the ANN for calculation. Several popular ANN structures are employed, including Convolutional Neural Network (CNN), Back Propagation (BP) Neural Network and Self-organizing Feature Map (SOFM). The advantages of the ANN recognition method are that ANNs have the ability to learn and generalize, and process faster. However, the recognition process of ANNs is opaque. Moreover, ANNs can only process numerical input and perform arithmetic operations, not logical operations, which restricts the application of ANNs in the field of CAD machining feature recognition. Therefore, it is essential to research and establish a new and more practical network structure. The contribution of this paper is that a new Visual-cognition-inspired Model (VCIM) for machining feature recognition especially in aircraft structural parts is established by imitating the visual cognition process of the human brain and related neural mechanisms.
- 24 June 2019
- Published by U-turn Press LLC
A Visual-cognition-inspired Model for Machining Feature Recognition
Artificial neural network (ANN) is a successful implementation of imitating biological neural network. Feature recognition is a key technology in CAD/CAM. Using ANN to identify machining features is a significant interdisciplinary research direction of feature recognition, and has received considerable results. The method mainly performs pre-processing and assigns features based on B-rep information or voxel representation, and then inputs them into the ANN for calculation. Several popular ANN structures are employed, including Convolutional Neural Network (CNN), Back Propagation (BP) Neural Network and Self-organizing Feature Map (SOFM). The advantages of the ANN recognition method are that ANNs have the ability to learn and generalize, and process faster. However, the recognition process of ANNs is opaque. Moreover, ANNs can only process numerical input and perform arithmetic operations, not logical operations, which restricts the application of ANNs in the field of CAD machining feature recognition. Therefore, it is essential to research and establish a new and more practical network structure. The contribution of this paper is that a new Visual-cognition-inspired Model (VCIM) for machining feature recognition especially in aircraft structural parts is established by imitating the visual cognition process of the human brain and related neural mechanisms.
- Open Access
- 24 June 2019
- Published by U-turn Press LLC
- p. 80-85
Calculation and Simulation of Elastic Deformation of Thin-walled Rings
The ring is regarded as one of the most traditional and effective buffer structures because of its simple manufacture and low cost. It has been widely used in the collision energy dissipation system of aircraft, automobiles and other vehicles. And energy-absorbing devices composed of the ring row are also applied to the protection of large structures and highways. Early related research focused on the large plastic deformation of the ring, such as Deruntz et al. compressed the quasi-static low-carbon steel tube radially, and proposed that the ring was deformed into a four-hinge mechanism and its bearing capacity was calculated; Yu Tongxi explored the influence of plastic deformation on the bearing capacity of the ring by diameter stretching the ring; Sowerby et al. first analyzed the influence of the point load on the radial direction of the ring on its deformation. However, when the ring collides at a lower speed, only elastic deformation occurs, and the current research on the elastic deformation mechanism of the ring is rare.
- 24 June 2019
- Published by U-turn Press LLC
- p. 80-85
Open AccessCalculation and Simulation of Elastic Deformation of Thin-walled Rings
The ring is regarded as one of the most traditional and effective buffer structures because of its simple manufacture and low cost. It has been widely used in the collision energy dissipation system of aircraft, automobiles and other vehicles. And energy-absorbing devices composed of the ring row are also applied to the protection of large structures and highways. Early related research focused on the large plastic deformation of the ring, such as Deruntz et al. compressed the quasi-static low-carbon steel tube radially, and proposed that the ring was deformed into a four-hinge mechanism and its bearing capacity was calculated; Yu Tongxi explored the influence of plastic deformation on the bearing capacity of the ring by diameter stretching the ring; Sowerby et al. first analyzed the influence of the point load on the radial direction of the ring on its deformation. However, when the ring collides at a lower speed, only elastic deformation occurs, and the current research on the elastic deformation mechanism of the ring is rare.
- 24 June 2019
- Published by U-turn Press LLC
Material-Unit Network for Multi-Material-Property and Multiscale Components
Currently, additive manufacturing technologies have already been widely used to fabricate parts with complex geometries. Porous structures with multiscale complexities can be fabricated by AM process without support structures. To take advantage of design freedom provided by AM, several design methods for additive manufacturing has been developed. However, it should be noted that most existing design methods only focus on structure’s geometry. Thus, most parts designed by existing DfAM methods are made of single materials. To further improve the performance of designed products, concurrent optimization methods which can update the distribution of material microstructures and structure’s macro geometry have been developed. Comparing to design optimization method focused on a single design scale, concurrent optimization methods can achieve better performance especially for design cases for multifunctional purposes. Even though, those concurrent optimization methods are promising in terms of their performance, none of the results of these optimization methods have been successfully fabricated by existing AM technologies.
- 24 June 2019
- Published by U-turn Press LLC
Material-Unit Network for Multi-Material-Property and Multiscale Components
Currently, additive manufacturing technologies have already been widely used to fabricate parts with complex geometries. Porous structures with multiscale complexities can be fabricated by AM process without support structures. To take advantage of design freedom provided by AM, several design methods for additive manufacturing has been developed. However, it should be noted that most existing design methods only focus on structure’s geometry. Thus, most parts designed by existing DfAM methods are made of single materials. To further improve the performance of designed products, concurrent optimization methods which can update the distribution of material microstructures and structure’s macro geometry have been developed. Comparing to design optimization method focused on a single design scale, concurrent optimization methods can achieve better performance especially for design cases for multifunctional purposes. Even though, those concurrent optimization methods are promising in terms of their performance, none of the results of these optimization methods have been successfully fabricated by existing AM technologies.
- 24 June 2019
- Published by U-turn Press LLC
Geometry Attributes Computation of Components’ 3D Model for Additive Manufacturing
From the view of manufacturing, process inspection of part is one of the most important evaluation whether a design part can be successfully manufactured in order to achieve its function. Geometry attributes computation of components’ 3D model based on manufacturing ability is a necessary and feasible method to inspect process for additive manufacturing (AM). As the printable thin walls may be limited by the type of AM process and resolution of the machine, or be so fragile as not to be able to survive post-processing, the minimum feature size is one of the most important AM constraints. As so far, MAT-based method (Medial Axis Transformation), distance transform method, peeling approach and offsetting method are the main methods for the computation of the minimum wall thickness (minimum feature size) of an object. The advantages and limitations of MAT and point-based offsetting operation can be found in reference. In Tedia and Williams’ research, the input triangular mesh model is first converted into a voxel representation using Ray Casting. When they computed the minimum feature size, they transformed the thickness problem into a 2D problem.
- 24 June 2019
- Published by U-turn Press LLC
Geometry Attributes Computation of Components’ 3D Model for Additive Manufacturing
From the view of manufacturing, process inspection of part is one of the most important evaluation whether a design part can be successfully manufactured in order to achieve its function. Geometry attributes computation of components’ 3D model based on manufacturing ability is a necessary and feasible method to inspect process for additive manufacturing (AM). As the printable thin walls may be limited by the type of AM process and resolution of the machine, or be so fragile as not to be able to survive post-processing, the minimum feature size is one of the most important AM constraints. As so far, MAT-based method (Medial Axis Transformation), distance transform method, peeling approach and offsetting method are the main methods for the computation of the minimum wall thickness (minimum feature size) of an object. The advantages and limitations of MAT and point-based offsetting operation can be found in reference. In Tedia and Williams’ research, the input triangular mesh model is first converted into a voxel representation using Ray Casting. When they computed the minimum feature size, they transformed the thickness problem into a 2D problem.
- 1 January 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 94 (1-4) , 585-597
An optimal approach to manufacturing planning for complex prismatic parts with interacting feature
- 1 January 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 94 (1-4) , 585-597
An optimal approach to manufacturing planning for complex prismatic parts with interacting feature
- 29 December 2016
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 91 (5-8) , 2059-2075
The algorithm of layering calculation for corner plunge milling tool path
- 29 December 2016
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 91 (5-8) , 2059-2075
The algorithm of layering calculation for corner plunge milling tool path
- 9 January 2012
- Published by Elsevier in Advances in Engineering Software
- Vol. 47 (1) , 51-61
Simulated rolling method for the recognition of outer profile faces of aircraft structural parts
- 9 January 2012
- Published by Elsevier in Advances in Engineering Software
- Vol. 47 (1) , 51-61
Simulated rolling method for the recognition of outer profile faces of aircraft structural parts