MZMin Zhou

Min Zhou

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Min Zhou has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Design and Laboratory Evaluation of a Lightweight Long-Reach Manipulator for Vision-Guided Positioning in Rabbit Feeding

    by Junyi Meng, Anqi Meng, Yang Shen, Yangbozhong Han, Zhaoyang Du, Wenqing Li, Hongying Wang, Min Zhou, Liangju Wang

    Automated feeding in cage-based rabbit production is challenging because cage geometry and limited workspace require a compact manipulator with sufficient reach, low mass, and reliable task-level positioning. This study developed a lightweight five-degree-of-freedom manipulator integrated with a vision-guided positioning framework for cage-based rabbit feeding applications. The prototype achieved an effective task reach of 1.20 m with a total mass of 12.37 kg. The design incorporated lightweight carbon-fiber-reinforced polymer (CFRP) long-span links, integrated actuators selected according to joint torque requirements, task-constrained kinematics, closed-form inverse kinematics, and Cartesian trajectory planning. A red–green–blue and depth (RGB-D) localization interface used four ordered feed-port keypoints and a horizontal-plane constraint to provide three-dimensional upper-tier task targets for the manipulator. All representative task points were numerically reachable under the defined software joint limits, and the maximum planned joint velocity was 0.525 rad s−1. Component-level linear-static finite-element analysis predicted no yielding in the four analyzed aluminum components under the simplified conservative 5 kg verification load case. Static loading of the assembled arm produced mean downward displacements of 3.0–20.0 mm at the J5 flange under 1–5 kg loads. Laboratory evaluation demonstrated three-dimensional repeatability radii of 1.68–4.63 mm. Across four upper-tier locations, the mean Euclidean feed-port localization error ranged from 9.01 to 20.47 mm, with all 80 trials satisfying the ±20 mm-per-axis criterion. The mean tool center point (TCP)-equivalent end-point error ranged from 18.23 to 37.15 mm. These laboratory results support the feasibility of the developed manipulator for upper-tier vision-guided positioning in rabbit-feeding geometry, while indicating that multi-point calibration and spatial compensation are needed to further reduce system-level positioning error. Validation was limited to laboratory testing; no feed was discharged and no rabbit-house operation was evaluated.

  • Open Access

    Calibration of DEM Contact Parameters for High-Moisture Rabbit Manure Using the Hertz–Mindlin with a JKR Model and a Three-Stage Optimization Strategy

    by Zhihang Cui, Min Zhou, Xun Suo, Zichen Yang

    Rabbit manure with high-moisture content exhibits complex adhesive and flow behaviors, which make accurate parameterization in discrete element method (DEM) simulations difficult. To improve the reliability of DEM modeling for rabbit manure composting processes, this study calibrated the contact parameters of rabbit manure at 65% moisture content using the angle of repose as the target response. A physical angle of repose test was first conducted using the cylindrical lifting method, yielding a measured value of 38.77°. The Hertz–Mindlin with Johnson–Kendall–Roberts (JKR) contact model was then adopted to represent the adhesive behavior of the material, and a three-stage optimization strategy consisting of a Plackett–Burman screening test, a steepest ascent test, and a Box–Behnken design was applied to identify and optimize the key parameters. The results showed that the particle restitution coefficient, rabbit manure–PLA rolling friction coefficient, and surface energy were the dominant factors affecting the angle of repose. The optimal parameter combination was a particle restitution coefficient of 0.56, a rabbit manure–PLA rolling friction coefficient of 0.375, and a surface energy of 0.243 J/m2. Under these conditions, the simulated angle of repose was 39.21°, with a relative error of 1.13%. These calibrated parameters provide a reliable basis for DEM simulation and engineering optimization of rabbit manure composting equipment.

  • Material-Unit Network for Multi-Material-Property and Multiscale Components

    by Yuan Liu, Min Zhou, Yunlong Tang, Yaoyao Zhao, Guolei Zheng

    Currently, additive manufacturing technologies have already been widely used to fabricate parts with complex geometries. Porous structures with multiscale complexities can be fabricated by AM process without support structures. To take advantage of design freedom provided by AM, several design methods for additive manufacturing has been developed. However, it should be noted that most existing design methods only focus on structure’s geometry. Thus, most parts designed by existing DfAM methods are made of single materials. To further improve the performance of designed products, concurrent optimization methods which can update the distribution of material microstructures and structure’s macro geometry have been developed. Comparing to design optimization method focused on a single design scale, concurrent optimization methods can achieve better performance especially for design cases for multifunctional purposes. Even though, those concurrent optimization methods are promising in terms of their performance, none of the results of these optimization methods have been successfully fabricated by existing AM technologies.

  • Geometry Attributes Computation of Components’ 3D Model for Additive Manufacturing

    by Min Zhou, Guolei Zheng

    From the view of manufacturing, process inspection of part is one of the most important evaluation whether a design part can be successfully manufactured in order to achieve its function. Geometry attributes computation of components’ 3D model based on manufacturing ability is a necessary and feasible method to inspect process for additive manufacturing (AM). As the printable thin walls may be limited by the type of AM process and resolution of the machine, or be so fragile as not to be able to survive post-processing, the minimum feature size is one of the most important AM constraints. As so far, MAT-based method (Medial Axis Transformation), distance transform method, peeling approach and offsetting method are the main methods for the computation of the minimum wall thickness (minimum feature size) of an object. The advantages and limitations of MAT and point-based offsetting operation can be found in reference. In Tedia and Williams’ research, the input triangular mesh model is first converted into a voxel representation using Ray Casting. When they computed the minimum feature size, they transformed the thickness problem into a 2D problem.