Severine Millet
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Severine Millet has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Valery Botton
Université Claude Bernard Lyon 1
16 shared publications - Daniel Henry
Laboratoire de Mécanique des Fluides et d'Acoustique, INSA Lyon, Ecole Centrale de Lyon, Université Claude Bernard Lyon 1, UMR5509 3 , 69621 Villeurbanne
15 shared publications H. Ben Hadid
Laboratoire de Mécanique des Fluides et d'Acoustique, CNRS/Université de Lyon, École Centrale de Lyon/Université Lyon 1/INSA Lyon, ECL, 36 avenue Guy de Collongue, 69134 Ecully Cedex, France
10 shared publicationsF. Rousset
Université de Lyon
5 shared publications- Ranganathan Usha
Department of Mathematics, Indian Institute of Technology Madras 1 , Chennai 600036, Tamilnadu, India
5 shared publications - Simon Dagois-Bohy
LMFA, UMR5509, CNRS, Ecole Centrale de Lyon, INSA Lyon, Universite Claude Bernard Lyon 1, Villeurbanne, France
5 shared publications
Latest Publications
- 1 September 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (9)
Eliminating artificial surfactant-mass drift in nonlinear weighted-residual models of soluble-surfactant-laden falling films
A soluble surfactant may adsorb at a free surface and desorb into the liquid bulk, but in a closed periodic falling film the total amount of surfactant must remain constant. We use this invariant as a test of nonlinear weighted-residual models for soluble-surfactant-laden films. The models of Pascal et al. [“Stability of inclined flow of a liquid film with soluble surfactants and variable mass density,” Phys. Rev. Fluids 4, 054004 (2019)] and D'Alessio et al. [“Marangoni instabilities associated with heated surfactant-laden falling films,” J. Fluid Mech. 887, A20 (2020)] correctly include the bulk-surface exchange mechanism, but their nonlinear surface closure contains a coefficient that prevents exact conservation of the reduced total surfactant mass. The problematic contribution is proportional to (5/4)ΓΓxhx: it leaves a residual ΓΓxhx that is not a conservative streamwise flux and therefore behaves as an artificial source during nonlinear evolution. We return to Stone's [“A simple derivation of the time-dependent convective-diffusion equation for surfactant transport along a deforming interface,” Phys. Fluids A 2, 111–112 (1990)] material-surface balance, add the Langmuir adsorption–desorption flux, and then take the thin-film long-wave limit used in the weighted-residual reduction. The normal-motion/curvature area-dilation term in Stone's [“A simple derivation of the time-dependent convective-diffusion equation for surfactant transport along a deforming interface,” Phys. Fluids A 2, 111–112 (1990)] equation is shown explicitly to enter two orders higher in the nondimensional surface balance than the retained Marangoni correction. With the same velocity and concentration ansatz used in the earlier weighted-residual framework, the conservative reduction gives the coefficient 1/4. The nonlinear surface term then becomes (1/4)∂x(hΓΓx), the corresponding bulk Marangoni term is also a periodic flux, and the adsorption–desorption terms cancel between the bulk and surface equations. Nonlinear simulations for a comparable parameter set based on the earlier published studies confirm that the corrected model conserves the total reduced surfactant mass to numerical accuracy and removes the secular growth in the surface concentration range, while leaving the linear stability problem unchanged.
- 1 September 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (9)
Eliminating artificial surfactant-mass drift in nonlinear weighted-residual models of soluble-surfactant-laden falling films
A soluble surfactant may adsorb at a free surface and desorb into the liquid bulk, but in a closed periodic falling film the total amount of surfactant must remain constant. We use this invariant as a test of nonlinear weighted-residual models for soluble-surfactant-laden films. The models of Pascal et al. [“Stability of inclined flow of a liquid film with soluble surfactants and variable mass density,” Phys. Rev. Fluids 4, 054004 (2019)] and D'Alessio et al. [“Marangoni instabilities associated with heated surfactant-laden falling films,” J. Fluid Mech. 887, A20 (2020)] correctly include the bulk-surface exchange mechanism, but their nonlinear surface closure contains a coefficient that prevents exact conservation of the reduced total surfactant mass. The problematic contribution is proportional to (5/4)ΓΓxhx: it leaves a residual ΓΓxhx that is not a conservative streamwise flux and therefore behaves as an artificial source during nonlinear evolution. We return to Stone's [“A simple derivation of the time-dependent convective-diffusion equation for surfactant transport along a deforming interface,” Phys. Fluids A 2, 111–112 (1990)] material-surface balance, add the Langmuir adsorption–desorption flux, and then take the thin-film long-wave limit used in the weighted-residual reduction. The normal-motion/curvature area-dilation term in Stone's [“A simple derivation of the time-dependent convective-diffusion equation for surfactant transport along a deforming interface,” Phys. Fluids A 2, 111–112 (1990)] equation is shown explicitly to enter two orders higher in the nondimensional surface balance than the retained Marangoni correction. With the same velocity and concentration ansatz used in the earlier weighted-residual framework, the conservative reduction gives the coefficient 1/4. The nonlinear surface term then becomes (1/4)∂x(hΓΓx), the corresponding bulk Marangoni term is also a periodic flux, and the adsorption–desorption terms cancel between the bulk and surface equations. Nonlinear simulations for a comparable parameter set based on the earlier published studies confirm that the corrected model conserves the total reduced surfactant mass to numerical accuracy and removes the secular growth in the surface concentration range, while leaving the linear stability problem unchanged.
- 14 August 2026
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 11 (8) , 084004
Solutocapillary instability in slipping falling films
Gravity-driven thin films laden with soluble surfactants play a central role in coating technologies and microfluidic systems, where reduced-order models are widely used to predict interfacial dynamics. Some weighted-residual formulations, however, introduce spurious interfacial mass growth, violating total surfactant conservation. We resolve this inconsistency by developing a conservative weighted-residual model that consistently couples wall slip, adsorption-desorption, and the Marangoni effect while rigorously preserving total surfactant mass. The resulting framework provides physically consistent predictions of instability onset, nonlinear wave dynamics, and surfactant transport.
- 14 August 2026
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 11 (8) , 084004
Solutocapillary instability in slipping falling films
Gravity-driven thin films laden with soluble surfactants play a central role in coating technologies and microfluidic systems, where reduced-order models are widely used to predict interfacial dynamics. Some weighted-residual formulations, however, introduce spurious interfacial mass growth, violating total surfactant conservation. We resolve this inconsistency by developing a conservative weighted-residual model that consistently couples wall slip, adsorption-desorption, and the Marangoni effect while rigorously preserving total surfactant mass. The resulting framework provides physically consistent predictions of instability onset, nonlinear wave dynamics, and surfactant transport.
- Open Access
- 19 November 2024
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 19 (11) , e0310805
Unifying the roll waves
Free surface flows down a slope occur in various real-life scenarios, such as civil engineering, industry, and natural hazards. Unstable waves can develop at the free surface when inertia is sufficiently strong, indicated by the Reynolds number exceeding a critical value. Although this instability has been investigated for specific fluids with different rheologies, a common framework is still lacking to facilitate comparison among the various models. In this study, we investigate the linear stability of a generalized Newtonian fluid, where the viscosity remains unspecified. We meticulously construct new dimensionless quantities to minimize dependence on the rheology, and subsequently derive the Orr-Sommerfeld equation of stability for any generalized Newtonian fluid, which has never been done before. We conduct a long-wave expansion and generate a novel analytical expression for the wave celerity, along with the critical Reynolds number. The originality in this study is that the analytical expressions obtained are valid for any rheology, and are easy to compute from a rheological measurement or from a base flow profile measurement. These results are subsequently scrutinized using various shear-thinning, shear-thickening, and viscoplastic rheology models. They exhibit excellent agreement with experimental or numerical data as well as theoretical findings from existing literature. Furthermore, the novel analytical expressions enable a much more comprehensive investigation into the impact of rheology on stability. While our approach does not encompass singular or non-monotonous rheology, the analytical expressions derived from the long-wave expansion exhibit remarkable resilience and they continue to accurately predict both the wave speed and the instability threshold in such cases.- 19 November 2024
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 19 (11) , e0310805
Open AccessUnifying the roll waves
Free surface flows down a slope occur in various real-life scenarios, such as civil engineering, industry, and natural hazards. Unstable waves can develop at the free surface when inertia is sufficiently strong, indicated by the Reynolds number exceeding a critical value. Although this instability has been investigated for specific fluids with different rheologies, a common framework is still lacking to facilitate comparison among the various models. In this study, we investigate the linear stability of a generalized Newtonian fluid, where the viscosity remains unspecified. We meticulously construct new dimensionless quantities to minimize dependence on the rheology, and subsequently derive the Orr-Sommerfeld equation of stability for any generalized Newtonian fluid, which has never been done before. We conduct a long-wave expansion and generate a novel analytical expression for the wave celerity, along with the critical Reynolds number. The originality in this study is that the analytical expressions obtained are valid for any rheology, and are easy to compute from a rheological measurement or from a base flow profile measurement. These results are subsequently scrutinized using various shear-thinning, shear-thickening, and viscoplastic rheology models. They exhibit excellent agreement with experimental or numerical data as well as theoretical findings from existing literature. Furthermore, the novel analytical expressions enable a much more comprehensive investigation into the impact of rheology on stability. While our approach does not encompass singular or non-monotonous rheology, the analytical expressions derived from the long-wave expansion exhibit remarkable resilience and they continue to accurately predict both the wave speed and the instability threshold in such cases. - 3 August 2023
- Published by Springer Nature in The European Physical Journal E
- Vol. 46 (8) , 1-8
Nonlinear evolution of viscoplastic film flows down an inclined plane
In this article, we experimentally investigate the nonlinear behaviour of a viscoplastic film flow down an inclined plane. We focus on the nonlinear instab
- 3 August 2023
- Published by Springer Nature in The European Physical Journal E
- Vol. 46 (8) , 1-8
Nonlinear evolution of viscoplastic film flows down an inclined plane
In this article, we experimentally investigate the nonlinear behaviour of a viscoplastic film flow down an inclined plane. We focus on the nonlinear instab
- Open Access
- 11 February 2022
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 936
Rayleigh–Bénard flow for a Carreau fluid in a parallelepiped cavity
A continuation method is used to study Rayleigh–Bénard convection in a non-Newtonian fluid inside a parallelepiped cavity. The cavity has its length equal to twice the side of the square cross-section. Shear-thinning and shear-thickening Carreau fluids are considered. The focus is put on the two stable branches which exist in the Newtonian case, a stable primary branch of transverse rolls $B_1$ and a primary branch of longitudinal roll $B_2$ , stabilized beyond a secondary bifurcation point $S_2$ . Although the primary bifurcation points are unchanged, the non-Newtonian properties strongly modify the bifurcation diagram. Indeed, for a shear-thinning fluid, the stable solutions can exist at much smaller Rayleigh numbers ${Ra}$ , on subcritical branches beyond saddle-node points $SN_1$ and $SN_2$ , and small perturbations can be sufficient to reach them. In agreement with Bouteraa et al. (J. Fluid Mech., vol. 767, 2015, pp. 696–734), the change of the primary bifurcations from supercritical to subcritical occurs at given values of what they define as the degree of shear-thinning parameter $\alpha$ . Moreover, the value of the Rayleigh number at the saddle-node points can be approximated by a simple expression, as proposed by Jenny et al. (J. Non-Newtonian Fluid Mech., vol. 219, 2015, pp. 19–34). In the case of a shear-thickening fluid, the branches remain supercritical, but the secondary point $S_2$ is strongly moved towards larger ${Ra}$ , making it more difficult to reach the longitudinal roll solution. Energy analyses at the bifurcations $SN_1$ , $SN_2$ and $S_2$ show that the changes of the corresponding critical thresholds ${Ra}_c$ are connected with the changes of the viscous properties, but also with changes of the buoyancy effect.- 11 February 2022
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 936
Open AccessRayleigh–Bénard flow for a Carreau fluid in a parallelepiped cavity
A continuation method is used to study Rayleigh–Bénard convection in a non-Newtonian fluid inside a parallelepiped cavity. The cavity has its length equal to twice the side of the square cross-section. Shear-thinning and shear-thickening Carreau fluids are considered. The focus is put on the two stable branches which exist in the Newtonian case, a stable primary branch of transverse rolls $B_1$ and a primary branch of longitudinal roll $B_2$ , stabilized beyond a secondary bifurcation point $S_2$ . Although the primary bifurcation points are unchanged, the non-Newtonian properties strongly modify the bifurcation diagram. Indeed, for a shear-thinning fluid, the stable solutions can exist at much smaller Rayleigh numbers ${Ra}$ , on subcritical branches beyond saddle-node points $SN_1$ and $SN_2$ , and small perturbations can be sufficient to reach them. In agreement with Bouteraa et al. (J. Fluid Mech., vol. 767, 2015, pp. 696–734), the change of the primary bifurcations from supercritical to subcritical occurs at given values of what they define as the degree of shear-thinning parameter $\alpha$ . Moreover, the value of the Rayleigh number at the saddle-node points can be approximated by a simple expression, as proposed by Jenny et al. (J. Non-Newtonian Fluid Mech., vol. 219, 2015, pp. 19–34). In the case of a shear-thickening fluid, the branches remain supercritical, but the secondary point $S_2$ is strongly moved towards larger ${Ra}$ , making it more difficult to reach the longitudinal roll solution. Energy analyses at the bifurcations $SN_1$ , $SN_2$ and $S_2$ show that the changes of the corresponding critical thresholds ${Ra}_c$ are connected with the changes of the viscous properties, but also with changes of the buoyancy effect. - 7 July 2021
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 922
Primary instability of a visco-plastic film down an inclined plane: experimental study
We study experimentally the primary instability of a visco-plastic film flow down an inclined plane. The experimental set-up is a channel with a varying slope angle, in which a permanent flow of a Herschel–Bulkley fluid (carbopol or kaolin) is established. Controlled perturbations are imposed at the entrance of the channel to generate surface waves, and their downstream evolution is observed with a laser sensor system measuring the local fluid thickness. Growth rates and cutoff frequencies are obtained after processing the thickness signal, and experimental critical Reynolds and Bingham numbers are deduced. We find that the experimental stability map obtained is well described by the pseudo-plug model of Balmforth & Liu (J. Fluid Mech., vol, 519, 2004, pp. 33–54), a model obtained after neglecting the film thickness compared with its length. This is not the case for dispersion effects (growth rates, cutoff frequencies, phase speeds), for which a more accurate model is needed.
- 7 July 2021
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 922
Primary instability of a visco-plastic film down an inclined plane: experimental study
We study experimentally the primary instability of a visco-plastic film flow down an inclined plane. The experimental set-up is a channel with a varying slope angle, in which a permanent flow of a Herschel–Bulkley fluid (carbopol or kaolin) is established. Controlled perturbations are imposed at the entrance of the channel to generate surface waves, and their downstream evolution is observed with a laser sensor system measuring the local fluid thickness. Growth rates and cutoff frequencies are obtained after processing the thickness signal, and experimental critical Reynolds and Bingham numbers are deduced. We find that the experimental stability map obtained is well described by the pseudo-plug model of Balmforth & Liu (J. Fluid Mech., vol, 519, 2004, pp. 33–54), a model obtained after neglecting the film thickness compared with its length. This is not the case for dispersion effects (growth rates, cutoff frequencies, phase speeds), for which a more accurate model is needed.
- 1 June 2019
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 140, 167-183
A 2D1/2 model for natural convection and solidification in a narrow enclosure
- 1 June 2019
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 140, 167-183
A 2D1/2 model for natural convection and solidification in a narrow enclosure
- 21 March 2019
- Published by Springer Nature in Acta Mechanica
- Vol. 230 (6) , 2201-2220
The mechanism of long-wave instability in a shear-thinning film flow on a porous substrate
- 21 March 2019
- Published by Springer Nature in Acta Mechanica
- Vol. 230 (6) , 2201-2220
The mechanism of long-wave instability in a shear-thinning film flow on a porous substrate
- 1 January 2019
- Published by AIP Publishing in Physics of Fluids
- Vol. 31 (1) , 012103
Instabilities in viscosity-stratified two-fluid channel flow over an anisotropic-inhomogeneous porous bottom
A linear stability analysis of a pressure driven, incompressible, fully developed laminar Poiseuille flow of immiscible two-fluids of stratified viscosity and density in a horizontal channel bounded by a porous bottom supported by a rigid wall, with anisotropic and inhomogeneous permeability, and a rigid top is examined. The generalized Darcy model is used to describe the flow in the porous medium with the Beavers-Joseph condition at the liquid-porous interface. The formulation is within the framework of modified Orr-Sommerfeld analysis, and the resulting coupled eigenvalue problem is numerically solved using a spectral collocation method. A detailed parametric study has revealed the different active and coexisting unstable modes: porous mode (manifests as a minimum in the neutral boundary in the long wave regime), interface mode (triggered by viscosity-stratification across the liquid-liquid interface), fluid layer mode [existing in moderate or O(1) wave numbers], and shear mode at high Reynolds numbers. As a result, there is not only competition for dominance among the modes but also coalescence of the modes in some parameter regimes. In this study, the features of instability due to two-dimensional disturbances of porous and interface modes in isodense fluids are explored. The stability features are highly influenced by the directional and spatial variations in permeability for different depth ratios of the porous medium, permeability and ratio of thickness of the fluid layers, and viscosity-stratification. The two layer flow in a rigid channel which is stable to long waves when a highly viscous fluid occupies a thicker lower layer can become unstable at higher permeability (porous mode) to long waves in a channel with a homogeneous and isotropic/anisotropic porous bottom and a rigid top. The critical Reynolds number for the dominant unstable mode exhibits a nonmonotonic behaviour with respect to depth ratio. However, it increases with an increase in anisotropy parameter ξ indicating its stabilizing role. Switching of dominance of modes which arises due to variations in inhomogeneity of the porous medium is dependent on the permeability and the depth ratio. Inhomogeneity arising due to an increase in vertical variations in permeability renders short wave modes to become more unstable by enlarging the unstable region. This is in contrast to the anisotropic modulations causing stabilization by both increasing the critical Reynolds number and shrinking the unstable region. A decrease in viscosity-stratification of isodense fluids makes the configuration hosting a less viscous fluid in a thinner lower layer adjacent to a homogeneous, isotropic porous bottom to be more unstable than the one hosting a highly viscous fluid in a thicker lower layer. An increase in relative volumetric flow rate results in switching the dominant mode from the interface to fluid layer mode. It is evident from the results that it is possible to exercise more control on the stability characteristics of a two-fluid system overlying a porous medium in a confined channel by manipulating the various parameters governing the flow configurations. This feature can be effectively exploited in relevant applications by enhancing/suppressing instability where it is desirable/undesirable.
- 1 January 2019
- Published by AIP Publishing in Physics of Fluids
- Vol. 31 (1) , 012103
Instabilities in viscosity-stratified two-fluid channel flow over an anisotropic-inhomogeneous porous bottom
A linear stability analysis of a pressure driven, incompressible, fully developed laminar Poiseuille flow of immiscible two-fluids of stratified viscosity and density in a horizontal channel bounded by a porous bottom supported by a rigid wall, with anisotropic and inhomogeneous permeability, and a rigid top is examined. The generalized Darcy model is used to describe the flow in the porous medium with the Beavers-Joseph condition at the liquid-porous interface. The formulation is within the framework of modified Orr-Sommerfeld analysis, and the resulting coupled eigenvalue problem is numerically solved using a spectral collocation method. A detailed parametric study has revealed the different active and coexisting unstable modes: porous mode (manifests as a minimum in the neutral boundary in the long wave regime), interface mode (triggered by viscosity-stratification across the liquid-liquid interface), fluid layer mode [existing in moderate or O(1) wave numbers], and shear mode at high Reynolds numbers. As a result, there is not only competition for dominance among the modes but also coalescence of the modes in some parameter regimes. In this study, the features of instability due to two-dimensional disturbances of porous and interface modes in isodense fluids are explored. The stability features are highly influenced by the directional and spatial variations in permeability for different depth ratios of the porous medium, permeability and ratio of thickness of the fluid layers, and viscosity-stratification. The two layer flow in a rigid channel which is stable to long waves when a highly viscous fluid occupies a thicker lower layer can become unstable at higher permeability (porous mode) to long waves in a channel with a homogeneous and isotropic/anisotropic porous bottom and a rigid top. The critical Reynolds number for the dominant unstable mode exhibits a nonmonotonic behaviour with respect to depth ratio. However, it increases with an increase in anisotropy parameter ξ indicating its stabilizing role. Switching of dominance of modes which arises due to variations in inhomogeneity of the porous medium is dependent on the permeability and the depth ratio. Inhomogeneity arising due to an increase in vertical variations in permeability renders short wave modes to become more unstable by enlarging the unstable region. This is in contrast to the anisotropic modulations causing stabilization by both increasing the critical Reynolds number and shrinking the unstable region. A decrease in viscosity-stratification of isodense fluids makes the configuration hosting a less viscous fluid in a thinner lower layer adjacent to a homogeneous, isotropic porous bottom to be more unstable than the one hosting a highly viscous fluid in a thicker lower layer. An increase in relative volumetric flow rate results in switching the dominant mode from the interface to fluid layer mode. It is evident from the results that it is possible to exercise more control on the stability characteristics of a two-fluid system overlying a porous medium in a confined channel by manipulating the various parameters governing the flow configurations. This feature can be effectively exploited in relevant applications by enhancing/suppressing instability where it is desirable/undesirable.
- 1 October 2017
- Published by Elsevier in Journal of Crystal Growth
- Vol. 475, 55-69
Towards wall functions for the prediction of solute segregation in plane front directional solidification
- 1 October 2017
- Published by Elsevier in Journal of Crystal Growth
- Vol. 475, 55-69
Towards wall functions for the prediction of solute segregation in plane front directional solidification