Pierre Gilormini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Pierre Gilormini has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
H. Teyssèdre
Silsef, Archamps, and CEA/LETI, Grenoble, France
2 shared publications- Clara Argerich Martín
Airbus Group, Rue de l’Aviation, 44340 Bouguenais, France
1 shared publication - Francisco Chinesta
PIMM Research Laboratory, UMR 8006 CNRS-ENSAM-CNAM, Arts et Metiers Institute of Technology, Paris, France
1 shared publication G. Régnier
PIMM, Arts et Métiers ParisTech, CNRS, Paris, France
1 shared publication- Julie Diani
Laboratoire d'Ingénierie des Matériaux , CNRS, Arts et Métiers ParisTech, Paris, France
1 shared publication - Julie Diani
LMS, Ecole Polytechnique, CNRS, Université Paris-Saclay, Palaiseau, France
1 shared publication
Latest Publications
- Open Access
Learning the Macroscopic Flow Model of Short Fiber Suspensions from Fine-Scale Simulated Data
Fiber–fiber interaction plays an important role in the evolution of fiber orientation in semi-concentrated suspensions. Flow induced orientation in short-fiber reinforced composites determines the anisotropic properties of manufactured parts and consequently their performances. In the case of dilute suspensions, the orientation evolution can be accurately described by using the Jeffery model; however, as soon as the fiber concentration increases, fiber–fiber interactions cannot be ignored anymore and the final orientation state strongly depends on the modeling of those interactions. First modeling frameworks described these interactions from a diffusion mechanism; however, it was necessary to consider richer descriptions (anisotropic diffusion, etc.) to address experimental observations. Even if different proposals were considered, none of them seem general and accurate enough. In this paper we do not address a new proposal of a fiber interaction model, but a data-driven methodology able to enrich existing models from data, that in our case comes from a direct numerical simulation of well resolved microscopic physics.
Open AccessLearning the Macroscopic Flow Model of Short Fiber Suspensions from Fine-Scale Simulated Data
Fiber–fiber interaction plays an important role in the evolution of fiber orientation in semi-concentrated suspensions. Flow induced orientation in short-fiber reinforced composites determines the anisotropic properties of manufactured parts and consequently their performances. In the case of dilute suspensions, the orientation evolution can be accurately described by using the Jeffery model; however, as soon as the fiber concentration increases, fiber–fiber interactions cannot be ignored anymore and the final orientation state strongly depends on the modeling of those interactions. First modeling frameworks described these interactions from a diffusion mechanism; however, it was necessary to consider richer descriptions (anisotropic diffusion, etc.) to address experimental observations. Even if different proposals were considered, none of them seem general and accurate enough. In this paper we do not address a new proposal of a fiber interaction model, but a data-driven methodology able to enrich existing models from data, that in our case comes from a direct numerical simulation of well resolved microscopic physics.
- 1 March 2017
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 173, 32-40
Some features of the PPR cohesive-zone model combined with a linear unloading/reloading relationship
- 1 March 2017
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 173, 32-40
Some features of the PPR cohesive-zone model combined with a linear unloading/reloading relationship
- 19 September 2016
- Published by Springer Nature in Journal of Materials Science
- Vol. 52 (2) , 878-888
Effects of small particles on the mechanical behavior and on the local damage of highly filled elastomers
- 19 September 2016
- Published by Springer Nature in Journal of Materials Science
- Vol. 52 (2) , 878-888
Effects of small particles on the mechanical behavior and on the local damage of highly filled elastomers
- 1 February 2014
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 63, 51-61
Using a pattern-based homogenization scheme for modeling the linear viscoelasticity of nano-reinforced polymers with an interphase
- 1 February 2014
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 63, 51-61
Using a pattern-based homogenization scheme for modeling the linear viscoelasticity of nano-reinforced polymers with an interphase
- Open Access
- 8 December 2013
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 469 (2160) , 20130457
On using the levelling of the free surface of a Newtonian fluid to measure viscosity and Navier slip length
Measuring the relaxation time involved in the levelling of a free surface of a Newtonian fluid laid on a substrate can give access to material parameters. It is shown here how most favourable pattern geometries of the free surface and film thicknesses can be defined for the measures of viscosity and Navier slip length at the fluid–solid interface, respectively. Moreover, we put special emphasis on the conditions required to avoid shear thinning by controlling the maximum shear rate. For initially sinusoidal patterns with infinitesimal amplitudes, an analytical solution including slip at the fluid–solid interface is used, and numerical simulations based on the natural element method allow one to discuss the effect of finite amplitudes. This leads to the definition of a relevance domain for the analytical solution that avoids the need for numerical simulations in practical applications. It is also shown how these results can be applied to crenelated profiles, where Fourier series expansion can be used, but with caution.
- 8 December 2013
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 469 (2160) , 20130457
Open AccessOn using the levelling of the free surface of a Newtonian fluid to measure viscosity and Navier slip length
Measuring the relaxation time involved in the levelling of a free surface of a Newtonian fluid laid on a substrate can give access to material parameters. It is shown here how most favourable pattern geometries of the free surface and film thicknesses can be defined for the measures of viscosity and Navier slip length at the fluid–solid interface, respectively. Moreover, we put special emphasis on the conditions required to avoid shear thinning by controlling the maximum shear rate. For initially sinusoidal patterns with infinitesimal amplitudes, an analytical solution including slip at the fluid–solid interface is used, and numerical simulations based on the natural element method allow one to discuss the effect of finite amplitudes. This leads to the definition of a relevance domain for the analytical solution that avoids the need for numerical simulations in practical applications. It is also shown how these results can be applied to crenelated profiles, where Fourier series expansion can be used, but with caution.
- 1 March 2013
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 28 (1) , 72-78
Limitations of Simple Flow Models for the Simulation of Nanoimprint
A quick evaluation of the forces involved in nanoimprint would be very helpful in the prevention of mold deflection. Unfortunately, it is shown here that assuming simplified flows may lead to quite incorrect evaluations of these forces, even for simple periodic patterns and a Newtonian behavior. The mere use of the classical result of the lubrication theory does not account for the range of thickness-to-width ratios that may be involved, especially at the beginning of the process. An improved squeeze model includes this effect, but still underestimates the imprint force. Moreover, finite element simulations demonstrate limitations of two more elaborate models that are found in the literature. These simulations also show that two flow modes can be defined, according to whether or not the polymer touches the mold sidewalls. A deeper analysis of these two modes may help the definition of a more appropriate simplified model in the future.
- 1 March 2013
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 28 (1) , 72-78
Limitations of Simple Flow Models for the Simulation of Nanoimprint
A quick evaluation of the forces involved in nanoimprint would be very helpful in the prevention of mold deflection. Unfortunately, it is shown here that assuming simplified flows may lead to quite incorrect evaluations of these forces, even for simple periodic patterns and a Newtonian behavior. The mere use of the classical result of the lubrication theory does not account for the range of thickness-to-width ratios that may be involved, especially at the beginning of the process. An improved squeeze model includes this effect, but still underestimates the imprint force. Moreover, finite element simulations demonstrate limitations of two more elaborate models that are found in the literature. These simulations also show that two flow modes can be defined, according to whether or not the polymer touches the mold sidewalls. A deeper analysis of these two modes may help the definition of a more appropriate simplified model in the future.