Xiaodong Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Xiaodong Xu has a total of 110 co-authors. Here are the top co-authors by number of shared publications:
Jun Xu
School of Physics Science and Engineering, Institute for Advanced Study, Tongji University, Shanghai 200092, China
16 shared publications- Bin Xu
Xiamen University
13 shared publications Huiying Xu
Department of Electronic Engineering, Xiamen University, Xiamen 361005, China
12 shared publicationsZhiping Cai
Department of Electronic Engineering, Xiamen University, Xiamen 361005, China
12 shared publicationsJinglong Lan
Department of Electronic Engineering, Xiamen University, Xiamen 361005, China
8 shared publicationsXiaoxu Huang
Department of Electronic Engineering, Xiamen University, Xiamen 361005, People’s Republic of China
8 shared publications
Latest Publications
- Open Access
- 2 August 2018
- Published by Optica Publishing Group in Photonics Research
- Vol. 6 (9) , 830-836
Self-Q-switched and wavelength-tunable tungsten disulfide-based passively Q-switched Er:Y2O3 ceramic lasers
We report on diode-pumped ceramic lasers at about 2.7 μm in the tunable continuous-wave, self--switching and tungsten disulfide ()-based passively -switching regimes. For stable self--switched operation, the maximum output power reaches 106.6 mW under an absorbed power of 2.71 W. The shortest pulse width is measured to be about 1.39 μs at a repetition rate of 26.7 kHz at maximum output. Using a spin-coated as a saturable absorber, a passively -switched ceramic laser is also realized with a maximum average output power of 233.5 mW (for the first time, to the best of our knowledge). The shortest pulse width decreases to 0.72 μs at a corresponding repetition rate of 29.4 kHz, which leads to a pulse energy of 7.92 μJ and a peak power of 11.0 W. By inserting an undoped YAG thin plate as a Fabry–Perot etalon, for the passive switching, wavelength tunings are also demonstrated at around 2710, 2717, 2727, and 2740 nm.- 2 August 2018
- Published by Optica Publishing Group in Photonics Research
- Vol. 6 (9) , 830-836
Open AccessSelf-Q-switched and wavelength-tunable tungsten disulfide-based passively Q-switched Er:Y2O3 ceramic lasers
We report on diode-pumped ceramic lasers at about 2.7 μm in the tunable continuous-wave, self--switching and tungsten disulfide ()-based passively -switching regimes. For stable self--switched operation, the maximum output power reaches 106.6 mW under an absorbed power of 2.71 W. The shortest pulse width is measured to be about 1.39 μs at a repetition rate of 26.7 kHz at maximum output. Using a spin-coated as a saturable absorber, a passively -switched ceramic laser is also realized with a maximum average output power of 233.5 mW (for the first time, to the best of our knowledge). The shortest pulse width decreases to 0.72 μs at a corresponding repetition rate of 29.4 kHz, which leads to a pulse energy of 7.92 μJ and a peak power of 11.0 W. By inserting an undoped YAG thin plate as a Fabry–Perot etalon, for the passive switching, wavelength tunings are also demonstrated at around 2710, 2717, 2727, and 2740 nm. - 1 July 2018
- Published by Elsevier in Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy
- Vol. 200, 58-62
Crystal growth, polarized spectroscopy and Judd-Ofelt analysis of Tb:YAlO 3
- 1 July 2018
- Published by Elsevier in Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy
- Vol. 200, 58-62
Crystal growth, polarized spectroscopy and Judd-Ofelt analysis of Tb:YAlO 3
- Open Access
Fabrication and Sintering Behavior of Er:SrF2 Transparent Ceramics using Chemically Derived Powder
In this paper, we report the fabrication of high-quality 5 at. % Er3+ ions doped SrF2 transparent ceramics, the potential candidate materials for a mid-infrared laser-gain medium by hot-pressing at 700 °C for 40 h using a chemically-derived powder. The phase structure, densification, and microstructure evolution of the Er:SrF2 ceramics were systematically investigated. In addition, the grain growth kinetic mechanism of Er:SrF2 was clarified. The results showed lattice diffusion to be the grain growth mechanism in the Er:SrF2 transparent ceramic of which highest in-line transmittance reached 92% at 2000 nm, i.e., very close to the theoretical transmittance value of SrF2 single crystal. Furthermore, the emission spectra showed that the strongest emission band was located at 2735 nm. This means that it is possible to achieve a laser output of approximately 2.7 μm in the 5 at. % Er3+ ions doped SrF2 transparent ceramics.
Open AccessFabrication and Sintering Behavior of Er:SrF2 Transparent Ceramics using Chemically Derived Powder
In this paper, we report the fabrication of high-quality 5 at. % Er3+ ions doped SrF2 transparent ceramics, the potential candidate materials for a mid-infrared laser-gain medium by hot-pressing at 700 °C for 40 h using a chemically-derived powder. The phase structure, densification, and microstructure evolution of the Er:SrF2 ceramics were systematically investigated. In addition, the grain growth kinetic mechanism of Er:SrF2 was clarified. The results showed lattice diffusion to be the grain growth mechanism in the Er:SrF2 transparent ceramic of which highest in-line transmittance reached 92% at 2000 nm, i.e., very close to the theoretical transmittance value of SrF2 single crystal. Furthermore, the emission spectra showed that the strongest emission band was located at 2735 nm. This means that it is possible to achieve a laser output of approximately 2.7 μm in the 5 at. % Er3+ ions doped SrF2 transparent ceramics.
- 19 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 24 (5) , 1-7
Tm: Y2SiO5 Crystal: Effective Material for the Generation of Eye-Safe Laser Sources
We report on continuous-wave and passively Q-switched Tm: Y 2 SiO 5 (YSO) crystal lasers. For continuous-wave operation, a maximum output power of 3.23 W is achieved at 1969.8 nm with slope efficiency of 34.3%. The results represent the best laser performance that ever obtained in Tm 3+ -doped oxyorthosilicate materials. Effective continuous-wave lasers have been also obtained at 1976.0, 1972.9, and 2044.6 nm by using differently coated output couplers. Using Cr: ZnSe saturable absorber, passively Q-switched Tm: YSO lasers are realized at 1944 and 2022 nm, for the first time to our knowledge. The maximum average output power has reached 0.74 W with pulsewidth of 78.3 ns and the corresponding pulse energy is 71.8 μJ. The present results indicate that Tm: YSO lasers could be very potential as sources for 2-μm eye safety related applications.
- 19 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 24 (5) , 1-7
Tm: Y2SiO5 Crystal: Effective Material for the Generation of Eye-Safe Laser Sources
We report on continuous-wave and passively Q-switched Tm: Y 2 SiO 5 (YSO) crystal lasers. For continuous-wave operation, a maximum output power of 3.23 W is achieved at 1969.8 nm with slope efficiency of 34.3%. The results represent the best laser performance that ever obtained in Tm 3+ -doped oxyorthosilicate materials. Effective continuous-wave lasers have been also obtained at 1976.0, 1972.9, and 2044.6 nm by using differently coated output couplers. Using Cr: ZnSe saturable absorber, passively Q-switched Tm: YSO lasers are realized at 1944 and 2022 nm, for the first time to our knowledge. The maximum average output power has reached 0.74 W with pulsewidth of 78.3 ns and the corresponding pulse energy is 71.8 μJ. The present results indicate that Tm: YSO lasers could be very potential as sources for 2-μm eye safety related applications.
- 12 January 2018
- Published by Optica Publishing Group in Applied Optics
- Vol. 57 (3) , 371-376
Continuous-wave and chemical vapor deposition graphene-based passively Q-switched Er:Y_2O_3 ceramic lasers at 27 μm
We report on 976-nm diode-pumped ceramic lasers in continuous-wave and passively -switched regimes. The maximum output power of continuous-wave laser operation is about 0.78 W with slope efficiency of about 11.8% at 2.7 μm. Passively -switched ceramic laser operation with chemical vapor deposition (CVD) graphene as the saturable absorber is also demonstrated for the first time, to our knowledge. Using a monolayer CVD graphene, the achieved shortest pulse width is about 408 ns, while the shortest pulse width reduces to about 296 ns with pulse energy of 2.59 μJ and peak power of 8.77 W by using a three-layer CVD graphene. The results reveal that graphene is a very promising saturable absorber operating in the middle infrared spectral region.- 12 January 2018
- Published by Optica Publishing Group in Applied Optics
- Vol. 57 (3) , 371-376
Continuous-wave and chemical vapor deposition graphene-based passively Q-switched Er:Y_2O_3 ceramic lasers at 27 μm
We report on 976-nm diode-pumped ceramic lasers in continuous-wave and passively -switched regimes. The maximum output power of continuous-wave laser operation is about 0.78 W with slope efficiency of about 11.8% at 2.7 μm. Passively -switched ceramic laser operation with chemical vapor deposition (CVD) graphene as the saturable absorber is also demonstrated for the first time, to our knowledge. Using a monolayer CVD graphene, the achieved shortest pulse width is about 408 ns, while the shortest pulse width reduces to about 296 ns with pulse energy of 2.59 μJ and peak power of 8.77 W by using a three-layer CVD graphene. The results reveal that graphene is a very promising saturable absorber operating in the middle infrared spectral region.- 23 November 2017
- Published by IOP Publishing in Laser Physics
- Vol. 27 (12) , 125806
Diode-end-pumped Nd3+-doped oxyorthosilicate GYSO lasers operating on4F3/2 → 4I13/2transition
We report on diode-pumped continuous-wave Nd:GdYSiO 5 lasers, operating on the 4 F 3/2 → 4 I 13/2 transition around the 1.3 µ m spectral domain, for the first time to our knowledge. In free-running laser operation, a maximum output power of up to 0.81 W can be obtained at 1357.45 nm with a corresponding slope efficiency of about 10.9%. Wavelength tuning is also realized by using an etalon with a tuning range of about 4 nm. The low-gain emission line at 1386.23 nm is explored with a maximum output power of 0.21 W and a slope efficiency of about 5.3%, using an output coupler coated in a particular way.
- 23 November 2017
- Published by IOP Publishing in Laser Physics
- Vol. 27 (12) , 125806
Diode-end-pumped Nd3+-doped oxyorthosilicate GYSO lasers operating on4F3/2 → 4I13/2transition
We report on diode-pumped continuous-wave Nd:GdYSiO 5 lasers, operating on the 4 F 3/2 → 4 I 13/2 transition around the 1.3 µ m spectral domain, for the first time to our knowledge. In free-running laser operation, a maximum output power of up to 0.81 W can be obtained at 1357.45 nm with a corresponding slope efficiency of about 10.9%. Wavelength tuning is also realized by using an etalon with a tuning range of about 4 nm. The low-gain emission line at 1386.23 nm is explored with a maximum output power of 0.21 W and a slope efficiency of about 5.3%, using an output coupler coated in a particular way.
- 20 September 2017
- Published by Optica Publishing Group in Optics Letters
- Vol. 42 (19) , 3781-3784
Tm^3+-doped LuYO_3 mixed sesquioxide ceramic laser: effective 205 μm source operating in continuous-wave and passive Q-switching regimes
ceramic is reported as an effective laser gain medium, for the first time to the best of our knowledge. For continuous-wave laser operation, a maximum output power of 1.55 W with a slope efficiency of 19.9% is achieved at 2050 nm. Passive -switching of the ceramic is operated using a Cr:ZnSe saturable absorber. Single-wavelength -switching at 2047 nm is obtained with a maximum average output power of 0.54 W, a pulse width of 120.3 ns, a pulse energy of 20.5 μJ, and a pulse peak power of 170.6 W. Simultaneous dual-wavelength -switching at 1957 and 2047 nm is also attained with corresponding parameter values of 0.92 W, 151.6 ns, 30.2 μJ, and 199.1 W. These results indicate that ceramic lasers could be a promising laser source operating in the eye-safe spectral region.- 20 September 2017
- Published by Optica Publishing Group in Optics Letters
- Vol. 42 (19) , 3781-3784
Tm^3+-doped LuYO_3 mixed sesquioxide ceramic laser: effective 205 μm source operating in continuous-wave and passive Q-switching regimes
ceramic is reported as an effective laser gain medium, for the first time to the best of our knowledge. For continuous-wave laser operation, a maximum output power of 1.55 W with a slope efficiency of 19.9% is achieved at 2050 nm. Passive -switching of the ceramic is operated using a Cr:ZnSe saturable absorber. Single-wavelength -switching at 2047 nm is obtained with a maximum average output power of 0.54 W, a pulse width of 120.3 ns, a pulse energy of 20.5 μJ, and a pulse peak power of 170.6 W. Simultaneous dual-wavelength -switching at 1957 and 2047 nm is also attained with corresponding parameter values of 0.92 W, 151.6 ns, 30.2 μJ, and 199.1 W. These results indicate that ceramic lasers could be a promising laser source operating in the eye-safe spectral region.- Open Access
Diode-pumped mode-locked femtosecond 2-um Tm:CaYAlO4 laser
Continuous-wave mode-locked femtosecond 2 um solid-state laser with a c-cut Tm:CaYAlO4 as gain medium was experimentally demonstrated. The mode locked laser generated stable pulses with average output power as high as 531 mW, pulse duration of 496 fs, and repetition rate of 97 MHz at 1975 nm. The research results show that Tm:CaYAlO4 is an excellent gain medium for femtosecond pulse generation at 2um wavelength.
Open AccessDiode-pumped mode-locked femtosecond 2-um Tm:CaYAlO4 laser
Continuous-wave mode-locked femtosecond 2 um solid-state laser with a c-cut Tm:CaYAlO4 as gain medium was experimentally demonstrated. The mode locked laser generated stable pulses with average output power as high as 531 mW, pulse duration of 496 fs, and repetition rate of 97 MHz at 1975 nm. The research results show that Tm:CaYAlO4 is an excellent gain medium for femtosecond pulse generation at 2um wavelength.
- 9 May 2017
- Published by Optica Publishing Group in Applied Optics
- Vol. 56 (14) , 4191-4196
Laser characteristics of Nd^3+-doped calcium barium niobate ferroelectric crystal at 106 and 134 μm
We report on diode-pumped -doped calcium barium niobate ferroelectric crystal (Nd:CBN-28) lasers at 1.06 and 1.34 μm. The maximum output power of the 1.06 μm laser reaches 0.69 W in the continuous-wave regime, which is believed to be the highest output power with Nd:CBN-28 crystal to date. Using a chopper to modulate the pump, the highest output power further improves to 0.77 W. Passively -switched laser operation at 1.06 μm, using a Cr:YAG saturable absorber, is realized with a maximum average output power of 89 mW, a pulse width of 220 ns, and a pulse energy 10.8 μJ. A quasi-continuous-wave laser at 1.34 μm with a chopper is also demonstrated with maximum output power of 56 mW. The scaled output power in the fundamental wave should be favorable for the investigation on broadband nonlinear self-frequency conversion into visible.- 9 May 2017
- Published by Optica Publishing Group in Applied Optics
- Vol. 56 (14) , 4191-4196
Laser characteristics of Nd^3+-doped calcium barium niobate ferroelectric crystal at 106 and 134 μm
We report on diode-pumped -doped calcium barium niobate ferroelectric crystal (Nd:CBN-28) lasers at 1.06 and 1.34 μm. The maximum output power of the 1.06 μm laser reaches 0.69 W in the continuous-wave regime, which is believed to be the highest output power with Nd:CBN-28 crystal to date. Using a chopper to modulate the pump, the highest output power further improves to 0.77 W. Passively -switched laser operation at 1.06 μm, using a Cr:YAG saturable absorber, is realized with a maximum average output power of 89 mW, a pulse width of 220 ns, and a pulse energy 10.8 μJ. A quasi-continuous-wave laser at 1.34 μm with a chopper is also demonstrated with maximum output power of 56 mW. The scaled output power in the fundamental wave should be favorable for the investigation on broadband nonlinear self-frequency conversion into visible.- Open Access
- 1 May 2017
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 7 (6) , 1725-1731
Passively Q-Switched Tm:CaGdAlO_4 laser using a Cr^2+:ZnSe saturable absorber
Diode-pumped Tm:CGA lasers at 1938 and 1854 nm are reported in continuous-wave and Q-switched regimes. For continuous-wave laser operation, the maximum output powers for the two lasers are 3.05 and 2.41 W with slope efficiencies of 33.7% and 28.5%, respectively. For Q-switching, using a Cr:ZnSe saturable absorber, the maximum average output powers reach 0.64 and 0.37 W with corresponding shortest pulse widths, maximum pulse repetition rates, maximum pulse energies and maximum pulse peak powers of (44ns, 13.9 kHz, 46 μJ, 1.04 kW) and (47 ns, 9.9 kHz, 37.4 μJ, 0.79 kW), respectively.
- 1 May 2017
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 7 (6) , 1725-1731
Open AccessPassively Q-Switched Tm:CaGdAlO_4 laser using a Cr^2+:ZnSe saturable absorber
Diode-pumped Tm:CGA lasers at 1938 and 1854 nm are reported in continuous-wave and Q-switched regimes. For continuous-wave laser operation, the maximum output powers for the two lasers are 3.05 and 2.41 W with slope efficiencies of 33.7% and 28.5%, respectively. For Q-switching, using a Cr:ZnSe saturable absorber, the maximum average output powers reach 0.64 and 0.37 W with corresponding shortest pulse widths, maximum pulse repetition rates, maximum pulse energies and maximum pulse peak powers of (44ns, 13.9 kHz, 46 μJ, 1.04 kW) and (47 ns, 9.9 kHz, 37.4 μJ, 0.79 kW), respectively.