Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anna A. Kamenskikh has a total of 47 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    From Prototyping to High-Tech Industries: Current State and Prospects of Vat Photopolymerization

    by Anna A. Kamenskikh, Dmitry O. Pustovalov, Maria A. Ran, Veronika I. Strukova, Yulia S. Kuznetsova, Ilia V. Vindokurov, Mikhail A. Tashkinov

    Vat photopolymerization (VPP) technologies, including stereolithography (SLA), digital light processing (DLP), and liquid crystal display (LCD) printing, have moved beyond rapid prototyping to become a full-fledged platform for the digital manufacturing of functional products over the past decade. The layer-by-layer curing of liquid photosensitive compositions under ultraviolet (UV) or near-UV radiation is the fundamental principle of these methods. This provides high spatial resolution, good surface quality, and broad geometric freedom. This review systematizes and critically analyzes current data on photopolymer 3D printing. The mechanisms of radical and cationic photopolymerization, theoretical models of curing, and rheological behavior are discussed. Typical defects arising during printing and postprocessing are analyzed. Particular attention is paid to the evolution of materials: from traditional acrylate resins to thermosetting engineering composites, elastomers, ceramic and metal suspensions, carbon nanocomposites, biocompatible hydrogels, and recyclable photopolymers with dynamic covalent bonds. Technological innovations, including multi-material printing, grayscale DLP printing, high-speed methods, and the integration of artificial intelligence algorithms, are also considered. Further progress in VPP is shown to depend on the combined optimization of resin composition, rheology, optical properties, exposure parameters, and postprocessing regimes. The key limitations remain the light scattering and absorption in filled systems, volumetric shrinkage and residual stresses, defect formation, insufficient standardization, and the fragmented nature of the available property data. Visible-range photoinitiators, closed-loop recycling, multi-material 4D printing and digital quality management are identified as promising directions.

  • Open Access

    Experimental Study of the Rheological and Thermomechanical Properties of Greases

    by Yuriy O. Nosov, Anna A. Kamenskikh, Alexandr V. Nikolaev

    Greases are structured multicomponent systems whose performance depends on the composition of the base oil, the type and concentration of the thickener, the presence of functional additives, temperature, and the deformation regime. Standard reference characteristics of greases do not allow a full assessment of their actual mechanical state. This is due to the fact that viscosity, dynamic moduli, and shear resistance change non-linearly. Materials of the same class with minor compositional differences may exhibit different reactions to external influences. This makes it important to compare the performance of materials under identical deformation conditions. An experimental study of four greases was performed in this work: CIATIM-221, CIATIM-221F, TOMFLON SK 170FH, and TOMFLON SBS 240FM. Tests were conducted on a Discovery HR2 rotational viscometer with a thermal measurement system in a temperature range from −40 to +80 °C and dynamic deformation frequencies from 0.01 to 100 Hz. The study included two types of experiments: (i) temperature sweeps at a fixed deformation amplitude; (ii) frequency sweeps at a constant temperature. It was established that for all materials across the entire studied temperature range, the storage modulus exceeds the loss modulus . This corresponds to indicating a predominantly elastic or gel-like structural state at small oscillating deformations. Upon cooling, a pronounced non-linear increase in viscosity and shear stresses is observed, most pronounced at sub-zero temperatures. The frequency dependence of the shear stress is satisfactorily described by the Ostwald–de Waele power law. The exponent remains less than one, which corresponds to a pseudoplastic behavior and a decrease in effective viscosity with increasing shear rate. Comparative analysis of the materials shows that the greatest differentiation of properties manifests at sub-zero temperatures.

  • Open Access

    Numerical and Experimental Determination of the Effective Mechanical Characteristics of a Polymer–Grease Contact Pair

    by Anna A. Kamenskikh, Yuriy O. Nosov, Andrey R. Muhametshin

    Contact polymer–grease pairs of materials are widely used in highly loaded friction units. However, modeling the joint mechanical deformation of polymer grease significantly increases computational costs and complicates the convergence of the numerical solution. This is due to the pronounced nonlinear behavior of the materials and the significant difference in their physical and mechanical characteristics. Modeling the behavior of complex spatial configurations of structures, taking into account temperature and time factors, and investigating the behavior of structures in dynamics challenges researchers and engineers with the task of reducing computational costs for numerical experiments without loss of accuracy. Therefore, it is of great importance to design methods and approaches for describing effective characteristics, taking into account the nonlinear behavior of a polymer–grease pair of materials. Representing the design volumes of polymer grease as an equivalent medium can reduce computational costs. This paper considers the design volume, including a polymer base made of ultrahigh-molecular-weight polyethylene and a spherical recess filled with CIATIM-221 grease. The modified elastic–viscoplastic Anand model has been used to describe the behavior of materials and an equivalent medium. The model parameters have been determined based on a set of numerical experiments at various temperatures, deformation rates, and sizes of the design volume. The effective elastic and viscoplastic characteristics of the equivalent medium have been determined. An increase in temperature leads to a decrease in stiffness and resistance to viscoplastic flow. Increasing the size of the design volume helps to stabilize effective characteristics and reduce the impact of local structural heterogeneities. The proposed analytical dependencies make it possible to take into account the influence of temperature and the geometry of the design volume when determining the parameters of an equivalent medium. The developed approach can be used in finite element modeling of large structures with friction units to reduce computational costs without explicitly modeling the polymer–grease interface.

  • Open Access

    Thermal Degradation and Thermomechanics of Castable Photopolymer Resins After Curing

    by Anna A. Kamenskikh, Dmitry O. Pustovalov, Veronika I. Strukova

    This current work considers six specialized castable photopolymers from different manufacturers that are promising for the formation of a process map for casting using burnt models: Harz Labs Dental Cast Cherry; Gorky Liquid Castable; Gorky Liquid Dental Castable; JAMG HE Ultra Cast UV Resin (90% WAX); JAMG HE Jewelry Casting Resin (25% WAX); Siraya Tech Cast Royal Blue. The additive growth parameters of the structures were selected to provide quality indicators of photopolymer models. Thermogravimetric analysis and dynamic mechanical analysis were chosen as the main methods of experimental analysis. Thermogravimetric analysis was performed at temperatures up to 700 °C. Thermal decomposition of castable photopolymers has several stages of decomposition with different rates of destruction. Gorky Liquid Castable has the fastest thermal decomposition. The material has less than 1% of the residual weight at 530 °C. The minimum ash content is in Siraya Tech Cast Royal Blue (less than 0.1%). Dynamic mechanical analysis was performed at temperatures up to 225 °C for samples grown in different printing directions. The printing direction affects the storage modulus, loss modulus, and tangent of the angle of mechanical losses of photopolymer materials, on average by no more than 35%. Glass transition temperatures of materials and zones of relaxation transitions are established. The glass transition temperatures depend little on the direction of printing of the samples. JAMG HE Ultra Cast UV Resin (90% WAX), a photopolymer with a maximum wax content, has the minimum glass transition temperature of 30–32 °C. JAMG HE Ultra Cast UV Resin (90% WAX) does not have a pronounced relaxation transition zone.


  • Open Access

    Numerical and Experimental Determination of the Effective Mechanical Characteristics of a Polymer-Grease Contact Pair

    by Anna A. Kamenskikh, Yuriy O. Nosov, Andrey R. Muhametshin

    Contact polymer-grease pairs of materials are widely used in highly loaded friction units. However, modeling the joint mechanical deformation of polymer grease significantly increases computational costs and complicates the convergence of the numerical solution. This is due to the pronounced nonlinear behavior of the materials and the significant difference in their physical and mechanical characteristics. Modeling the behavior of complex spatial configurations of structures, taking into account temperature and time factors, and investigating the behavior of structures in dynamics challenges researchers and engineers with the task of reducing computational costs for numerical experiments without loss of accuracy. Therefore, it is of high importance to form methods and approaches for describing effective characteristics, taking into account the nonlinear behavior of a polymer-grease pair of materials. Representing the design volumes of polymer grease as an equivalent medium can reduce computational costs. This paper considers the design volume, including a polymer base made of ultrahigh-molecular-weight polyethylene and a spherical recess filled with CIATIM-221 grease. The modified elastic-viscoplastic Anand model has been used to describe the behavior of materials and an equivalent medium. The model parameters have been determined based on a set of numerical experiments at various temperatures, deformation rates, and sizes of the design volume. The effective elastic and viscoplastic characteristics of the equivalent medium have been determined. An increase in temperature leads to a decrease in stiffness and resistance to viscoplastic flow. Increasing the size of the design volume helps to stabilize effective characteristics and reduce the impact of local structural heterogeneities. The proposed analytical dependencies make it possible to take into account the influence of temperature and the geometry of the design volume when determining the parameters of an equivalent medium. The developed approach can be used in finite element modeling of large structures with friction units to reduce computational costs without explicitly modeling the polymer-grease interface.

  • Open Access

    Thermal Degradation and Thermomechanics of Castable Photopolymer Resins After Curing

    by Anna A. Kamenskikh, Dmitry O. Pustovalov, Veronika I. Strukova

    The quality of castings using the technology of investment casting depends on the thermophysical and thermomechanical properties of photopolymer models. Determining the dependence of mechanical parameters on temperature will rationalize the process of burning out photopolymer models from casting molds. The current work considers six specialized castable photopolymer resins from different manufacturers: Harz Labs Dental Cast Cherry; Gorky Liquid Castable; Gorky Liquid Dental Castable; JAMG HE Ultra Cast UV Resin (90% WAX); JAMG HE Jewelry Casting Resin (25% WAX); Siraya Tech Cast Royal Blue. The additive growth parameters of the structures were selected to provide quality indicators of photopolymer models. Thermogravimetric analysis and dynamic mechanical analysis were chosen as the main methods of experimental analysis. Thermogravimetric analysis was performed at temperatures up to 700°C. Thermal decomposition of castable photopolymers has several stages of decomposition with different rates of destruction. Gorky Liquid Castable has the fastest thermal decomposition. The material has less than 1% of the residual weight at 530°C. The minimum ash content is in Siraya Tech Cast Royal Blue (less than 0.1%). Dynamic mechanical analysis was performed at temperatures up to 225°C for samples grown in different printing directions. The printing direction affects the storage modulus, the loss modulus, and the tangent of the angle of mechanical losses of photopolymer materials, on average by no more than 35%. Glass transition temperatures of materials and zones of relaxation transitions are established. The glass transition temperatures depend little on the direction of printing of the samples. JAMG HE Ultra Cast UV Resin (90% WAX), a photopolymer with a maximum wax content, has the minimum glass transition temperature of 30–32°C. JAMG HE Ultra Cast UV Resin (90% WAX) does not have a pronounced relaxation transition zone. The established temperature dependencies of destruction, the storage modulus, the loss modulus, and the tangent of the loss angle are necessary for the formation of a numerical model of materials and stages of the technological process of investment casting.

  • Open Access

    Analysis of Viscoelastic Behavior of Antifriction Layer Materials in Bridge Spherical Bearings under Thermomechanical Loading

    by Anna A. Kamenskikh, Anastasia P. Bogdanova, Yuriy O. Nosov, Yulia S. Kuznetsova

    Thermoplastic polymeric materials have found wide application as protective and antifriction coatings and interlayers of friction units. Spherical bearings include relatively thin sliding layers made of antifriction materials. Polytetrafluoroethylene (PTFE) is widely used as a material for sliding layers. However, at present, there are modern composite and modified materials with improved physical and mechanical properties that can be used as sliding layers. Antifriction materials are often modeled in terms of elasticity theory or elastoplasticity theory. However, it has been established that these materials exhibit viscoelastic properties. A series of experiments to determine the thermomechanical properties of the materials is performed in the current work. PTFE, a metal composite based on PTFE with bronze inclusions (MAK (F4BR40M2)) and structurally modified Arflon AR-200 PTFE were investigated using dynamic mechanical analysis. The temperature change range [-40; +80] °C was considered, it corresponds to the operating temperatures of bridge structures. Temperature dependencies of the storage modulus, loss modulus and loss tangent were obtained. Viscoelastic models of material behavior, such as Maxwell bodies using Prony series and temperature-time analogy, were constructed based on experimental data. Viscoelastic behavior of materials was analyzed in terms of deformation of a bridge spherical bearing under static and periodic loads, taking into account the ambient temperature. The relationships for the effect of temperature on the stress-strain response and contact parameters were obtained. The influence of the thermal expansion coefficient of materials on the structure behavior was considered. It was found that the sliding layer made of MAK allows for a more favorable stress-strain state compared to the structure including a sliding layer made of PTFE: the maximum stress intensity is less by ~ 3%; the maximum strain intensity is less by ~ 20%; displacements along the normal to the sliding layer are less by ~ 17.2%.

  • Open Access

    Experimental Study and Numerical Modeling of Thermoviscoelastic Behavior of Antifriction Polymeric Materials

    by Anna A. Kamenskikh, Anastasia P. Bogdanova, Yuriy O. Nosov, Yulia S. Kuznetsova

    Five modifications of polytetrafluoroethylene (PTFE) are considered as a modern alternative to PTFE as sliding layers of bridge bearing parts. Radiation-modified PTFE without additives and with nano-additives as well as composites based on PTFE with bronze inclusions and nanomodified carbon fiber fillers were investigated. Ultra-high-molecular-weight polyethylene (UHMWPE) and classic pure PTFE were considered as control samples. The thermomechanical properties of the materials were studied within the framework of dynamic mechanical analysis in the operating temperature range of bridge structures [−40; +80] °C. The exit zones from the linear theory of viscoelasticity were established for all the materials considered. Temperature dependencies of the storage modulus and the loss modulus were determined. Thermoviscoelastic models of material behavior were constructed using a numerical identification procedure, experimental data, and simulation models. The thermomechanics of materials during the deformation of the spherical support part of the bridge were analyzed. Temperature dependencies of the parameters of the contact stress-strain state were determined with an average coefficient of determination R2 = 0.97 and an average error size RMSE = 0.092.


  • Open Access

    Thermo-Viscoelastic Behavior of Antifriction Polymeric Materials

    by Anna A. Kamenskikh, Anastasia P. Bogdanova, Yuriy O. Nosov, Yulia S. Kuznetsova

    Five modifications of polytetrafluoroethylene (PTFE) are considered as a modern alternative to PTFE as sliding layers of bridge bearing parts. Radiation-modified PTFE without additives and with nano-additives, as well as composites based on PTFE with bronze inclusions and nanomodified carbon fiber fillers, were investigated. Ultra-high-molecular-weight polyethylene (UHMWPE) and classic pure PTFE were considered as control samples. The thermomechanical properties of the materials were studied within the framework of dynamic mechanical analysis in the operating temperature range of bridge structures [−40; +80] °C. The exit zones from the linear theory of viscoelasticity were established for all the materials considered. Temperature dependencies of the storage module and the loss module were determined. Thermo-viscoelastic models of material behavior were constructed using a numerical identification procedure, experimental data, and simulation models. The thermomechanics of materials during the deformation of the spherical support part of the bridge were analyzed. Temperature dependencies of the parameters of the contact stress-strain state were determined with an average coefficient of determination R2 = 0.97 and an average error size RMSE = 0.092.

  • Open Access

    Thermomechanics and Thermophysics of Optical Fiber Polymer Coating

    by Aleksandr N. Trufanov, Anna A. Kamenskikh, Yulia I. Lesnikova

    The viscoelastic properties of ultraviolet radiation-curable polymer coatings of optical fibers were studied experimentally and numerically. The test setup was completed, and a series of natural experiments were conducted for an extended temperature range from −110 °C to +120 °C using a dynamic mechanical analyzer (DMA). Discrete dependencies of the complex modulus on temperature and frequency of kinematic loading were obtained. The problem of multiparametric optimization was solved. Defining relations were obtained for protective coating polymers, making it possible to describe the thermomechanical behavior of the glass-forming materials under consideration in a wide temperature range, including relaxation transition. The optimal solution was found for 18 series terms at the selected reference temperature Tr = −70 °C, C1 = 20.036, and C2 = 32.666 for the DeSolite 3471-1-152A material. The optimal solution was found for 60 series terms at the selected reference temperature Tr = 0 °C, C1 = 40,242.2827, and C2 = 267,448.888 for the DeSolite DS-2015 material. The models were verified according to the data of creep experiments. The capabilities of the viscoelastic model were demonstrated by the example of a numerical experiment on free thermal heating/cooling of a Panda-type optical fiber.