Taichi Matsuoka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Taichi Matsuoka has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Katsuaki Sunakoda
Akita University
10 shared publications - Kazuhiko Hiramoto
Mechanical Engineering Program, Niigata University, 8050 Ikarashi 2-no-cho, Nishi-ku, Niigata 950-2181, Japan
7 shared publications Akira Fukukita
Shimizu Corporation, Tokyo, Japan
1 shared publicationMasaki Zeniya
Akita University
1 shared publicationNagato Aizawa
Toshiba Elevator and Building Systems Corporation
1 shared publicationNaoto Abe
Meiji University, School of Science and Technology
1 shared publication
Latest Publications
- Open Access
- 1 January 2023
- Published by Japan Society of Mechanical Engineers in Transactions of the JSME (in Japanese)
- Vol. 89 (917) , 22-00255
Vibration suppression device that has variable moment of inertia using magneto-rheological fluid (Seismic test during switching series inertia mass by reinforcement learning)
In previous paper the authors successfully developed a vibration suppression device (VSD) that has variable moment of inertia using Magneto-Rheological (MR) fluid. The MR fluid is filled into a flywheel. Ferrite particles of the MR fluid are clustered when magnetic field is applied to the flywheel by electromagnets, series inertia mass of the VSD will be switchable. In this paper seismic tests during switching series inertia mass by reinforcement learning are focused in order to get more vibration reduction while random excitations. Firstly, agents are trained by the reinforcement learning using Deep Deterministic Policy Gradient (DDPG) algorithm while a one-degree-of-freedom system with the VSD, which has the switchable series inertia mass, is excited under earthquakes. Secondly, the VSD is improved for having 8 electromagnets, magnetic field is analyzed by FEM, resisting force characteristics and response performance of the VSD are investigated. Then, to confirm the vibration control under some earthquakes, seismic tests of one degree-of-freedom system with the VSD under the reinforcement learning using DDPG are carried out by a shaking table, and seismic responses are simulated numerically. From the experimental results, the peaks of response acceleration and displacement decrease about 1/2 in case with the VSD using DDPG, and also cut 20 % by switching series inertia mass. Finally, validity of vibration reduction during switching series inertia mass by the reinforcement learning is confirmed.
- 1 January 2023
- Published by Japan Society of Mechanical Engineers in Transactions of the JSME (in Japanese)
- Vol. 89 (917) , 22-00255
Open AccessVibration suppression device that has variable moment of inertia using magneto-rheological fluid (Seismic test during switching series inertia mass by reinforcement learning)
In previous paper the authors successfully developed a vibration suppression device (VSD) that has variable moment of inertia using Magneto-Rheological (MR) fluid. The MR fluid is filled into a flywheel. Ferrite particles of the MR fluid are clustered when magnetic field is applied to the flywheel by electromagnets, series inertia mass of the VSD will be switchable. In this paper seismic tests during switching series inertia mass by reinforcement learning are focused in order to get more vibration reduction while random excitations. Firstly, agents are trained by the reinforcement learning using Deep Deterministic Policy Gradient (DDPG) algorithm while a one-degree-of-freedom system with the VSD, which has the switchable series inertia mass, is excited under earthquakes. Secondly, the VSD is improved for having 8 electromagnets, magnetic field is analyzed by FEM, resisting force characteristics and response performance of the VSD are investigated. Then, to confirm the vibration control under some earthquakes, seismic tests of one degree-of-freedom system with the VSD under the reinforcement learning using DDPG are carried out by a shaking table, and seismic responses are simulated numerically. From the experimental results, the peaks of response acceleration and displacement decrease about 1/2 in case with the VSD using DDPG, and also cut 20 % by switching series inertia mass. Finally, validity of vibration reduction during switching series inertia mass by the reinforcement learning is confirmed.
- 1 January 2018
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 5 (6) , 18-00307
Electromagnetic damper using brushless direct drive DC motor
- 1 January 2018
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 5 (6) , 18-00307
Electromagnetic damper using brushless direct drive DC motor
- 1 January 2016
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Dynamics & Design Conference
- Vol. 2016
Variable inertia damper using magnetorheological fluid
- 1 January 2016
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Dynamics & Design Conference
- Vol. 2016
Variable inertia damper using magnetorheological fluid
- 31 July 2015
- Published by Hindawi Limited in Structural Control and Health Monitoring
- Vol. 23 (3) , 423-445
Semi-active vibration control of structural systems based on a reference active control law: output emulation approach
A new semi-active control strategy that approximates a predicted control output of a reference active control is proposed. A variable parameter of a semi-active control device is selected at every time instant so that the predicted control output of the semi-active control system becomes close to the corresponding predicted control output of the reference active control as much as possible. Parameters of the reference active control law are optimized in the premise of the aforementioned ‘output emulation’ strategy so that the control performance of the semi-active control becomes good and the ‘error’ in the sense of achieved control performance between the reference active control and semi-active control systems becomes small. A pole placement method based on a linear matrix inequality (LMI) framework is adopted as the reference active control law. Parameters to determine the domain in the complex plane where the closed-loop poles are placed are searched so that control performance of the semi-active control system based on the output emulation approach is optimized. Copyright © 2015 John Wiley & Sons, Ltd.
- 31 July 2015
- Published by Hindawi Limited in Structural Control and Health Monitoring
- Vol. 23 (3) , 423-445
Semi-active vibration control of structural systems based on a reference active control law: output emulation approach
A new semi-active control strategy that approximates a predicted control output of a reference active control is proposed. A variable parameter of a semi-active control device is selected at every time instant so that the predicted control output of the semi-active control system becomes close to the corresponding predicted control output of the reference active control as much as possible. Parameters of the reference active control law are optimized in the premise of the aforementioned ‘output emulation’ strategy so that the control performance of the semi-active control becomes good and the ‘error’ in the sense of achieved control performance between the reference active control and semi-active control systems becomes small. A pole placement method based on a linear matrix inequality (LMI) framework is adopted as the reference active control law. Parameters to determine the domain in the complex plane where the closed-loop poles are placed are searched so that control performance of the semi-active control system based on the output emulation approach is optimized. Copyright © 2015 John Wiley & Sons, Ltd.
- 21 November 2012
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 134 (6) , 061211
Simultaneous Optimal Design of the Lyapunov-Based Semi-Active Control and the Semi-Active Vibration Control Device: Inverse Lyapunov Approach
We address a simultaneous optimal design problem of a semi-active (SA) control law and design parameters in a semi-active control device for civil structures. The vibration control device (VCD) that is being developed by authors is used as the semi-active control device. The VCD is composed of a ball screw with a flywheel for the inertial resistance force and an electric motor with an electric circuit for the damping resistance force. A new bang–bang type semi-active control law referred to as inverse Lyapunov approach is proposed. In the inverse Lyapunov approach, the Lyapunov matrix in the bang–bang type semi-active control based on the Lyapunov function is searched so that the control performance of the semi-active control system is optimized. Design parameters to determine the Lyapunov function and those of the VCD are optimized with the genetic algorithm (GA). The effectiveness of the proposed approach is presented with simulation studies.
- 21 November 2012
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 134 (6) , 061211
Simultaneous Optimal Design of the Lyapunov-Based Semi-Active Control and the Semi-Active Vibration Control Device: Inverse Lyapunov Approach
We address a simultaneous optimal design problem of a semi-active (SA) control law and design parameters in a semi-active control device for civil structures. The vibration control device (VCD) that is being developed by authors is used as the semi-active control device. The VCD is composed of a ball screw with a flywheel for the inertial resistance force and an electric motor with an electric circuit for the damping resistance force. A new bang–bang type semi-active control law referred to as inverse Lyapunov approach is proposed. In the inverse Lyapunov approach, the Lyapunov matrix in the bang–bang type semi-active control based on the Lyapunov function is searched so that the control performance of the semi-active control system is optimized. Design parameters to determine the Lyapunov function and those of the VCD are optimized with the genetic algorithm (GA). The effectiveness of the proposed approach is presented with simulation studies.
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Dynamics & Design Conference
- Vol. 2012, _243-1_
243 Optimal Design of the Model and the Reference Control Law in Semi-Active Control
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Dynamics & Design Conference
- Vol. 2012, _243-1_
243 Optimal Design of the Model and the Reference Control Law in Semi-Active Control
- 1 January 2011
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Dynamics & Design Conference
- Vol. 2011, _443-1_
443 Simultaneous Design of the Low Order Structural Model and the Semi-Active Control Law for Improving the Control Performance
Various semi-active control methods have been proposed for vibration control of civil structures. In contrast to active vibration control systems, all semi-active control systems are essentially asymptotically stable because of the stability of the structural systems (with structural damping) themselves and the energy dissipating nature of the semi-active control law. In this study, by utilizing the above property on the stability of semi-active control systems, a reduced-order structural model and a semi-active control law are simultaneously obtained so that the performance of the resulting semi-active control system becomes good. Based on the above fact any semi-active control laws derived from some models stabilize all real-existing structural systems that have structural damping. It means that the difference of dynamic behaviors between the real structural system and the reduced-order mathematical model in the sense of the open-loop response is no longer an important issue. In other words, we do not have to consider the closed-loop stability, which is one of the most important constraints in active control, in the process of the reduced-order structural modeling and the semi-active control design. We can only focus on the control performance of the closed-loop system with the real structure with the (model-based) semi-active control law in obtaining the reduced-order model. The semi-active control law in the present study is based on the one step ahead prediction of the structural response. The Genetic Algorithm (GA) is adopted to obtain the reduced-order model and the semi-active control law based on the reduced order model.
- 1 January 2011
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Dynamics & Design Conference
- Vol. 2011, _443-1_
443 Simultaneous Design of the Low Order Structural Model and the Semi-Active Control Law for Improving the Control Performance
Various semi-active control methods have been proposed for vibration control of civil structures. In contrast to active vibration control systems, all semi-active control systems are essentially asymptotically stable because of the stability of the structural systems (with structural damping) themselves and the energy dissipating nature of the semi-active control law. In this study, by utilizing the above property on the stability of semi-active control systems, a reduced-order structural model and a semi-active control law are simultaneously obtained so that the performance of the resulting semi-active control system becomes good. Based on the above fact any semi-active control laws derived from some models stabilize all real-existing structural systems that have structural damping. It means that the difference of dynamic behaviors between the real structural system and the reduced-order mathematical model in the sense of the open-loop response is no longer an important issue. In other words, we do not have to consider the closed-loop stability, which is one of the most important constraints in active control, in the process of the reduced-order structural modeling and the semi-active control design. We can only focus on the control performance of the closed-loop system with the real structure with the (model-based) semi-active control law in obtaining the reduced-order model. The semi-active control law in the present study is based on the one step ahead prediction of the structural response. The Genetic Algorithm (GA) is adopted to obtain the reduced-order model and the semi-active control law based on the reduced order model.
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in The Proceedings of Autumn Conference of Tohoku Branch
- Vol. 2010.46, 77-78
306 Vibration Suppression Device that Utilizes Inertia Mass of non-Newtonian Fluid
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in The Proceedings of Autumn Conference of Tohoku Branch
- Vol. 2010.46, 77-78
306 Vibration Suppression Device that Utilizes Inertia Mass of non-Newtonian Fluid
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Dynamics & Design Conference
- Vol. 2010, _522-1_
522 Damping Device Using Magneto-Rheological Fluid for Railway Suspension Insulator
- 1 January 2010
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Dynamics & Design Conference
- Vol. 2010, _522-1_
522 Damping Device Using Magneto-Rheological Fluid for Railway Suspension Insulator
- 1 January 2010
- Published by ASME International
- p. 213-221
Simultaneous Optimal Design of the Lyapunov-Based Semi-Active Control and the Semi-Active Vibration Control Device: Inverse Lyapunov Approach
We address a simultaneous optimal design problem of a semi-active control law and design parameters in a vibration control device for civil structures. The Vibration Control Device (VCD) that is being developed by authors is used as the semi-active control device in the present paper. The VCD is composed of a mechanism of a ball screw with a flywheel for the inertial resistance force and an electric motor with an electric circuit for the damping resistance force. A new bang-bang type semi-active control law referred to as Inverse Lyapunov Approach is proposed as the semi-active control law. In the Inverse Lyapunov Approach the Lyapunov function is searched so that performance measures in structural vibration control are optimized in the premise of the bang-bang type semi-active control based on the Lyapunov function. The design parameters to determine the Lyapunov function and the design parameters of the VCD are optimized for the good performance of the semi-active control system. The Genetic Algorithm is employed for the optimal design.
- 1 January 2010
- Published by ASME International
- p. 213-221
Simultaneous Optimal Design of the Lyapunov-Based Semi-Active Control and the Semi-Active Vibration Control Device: Inverse Lyapunov Approach
We address a simultaneous optimal design problem of a semi-active control law and design parameters in a vibration control device for civil structures. The Vibration Control Device (VCD) that is being developed by authors is used as the semi-active control device in the present paper. The VCD is composed of a mechanism of a ball screw with a flywheel for the inertial resistance force and an electric motor with an electric circuit for the damping resistance force. A new bang-bang type semi-active control law referred to as Inverse Lyapunov Approach is proposed as the semi-active control law. In the Inverse Lyapunov Approach the Lyapunov function is searched so that performance measures in structural vibration control are optimized in the premise of the bang-bang type semi-active control based on the Lyapunov function. The design parameters to determine the Lyapunov function and the design parameters of the VCD are optimized for the good performance of the semi-active control system. The Genetic Algorithm is employed for the optimal design.