Sunil Patil
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sunil Patil has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Danesh Tafti
Virginia Polytechnic Institute and State University, Blacksburg, Virginia 24061
2 shared publications- Danesh K. Tafti
Virginia Polytechnic Institute and State University
1 shared publication - Hee-Koo Moon
Solar Turbines Incorporated, San Diego, CA
1 shared publication - Ram Srinivasan
Combustion Engineering, Solar Turbines, Inc., 2200 Pacific Highway, Mail Zone E-4, San Diego, CA 92186-5376
1 shared publication Srinath Ekkad
Virginia Polytechnic Institute and State University, Blacksburg, Va
1 shared publicationTeddy Sedalor
Virginia Polytechnic Institute and State University, Blacksburg, Va
1 shared publication
Latest Publications
- 25 March 2013
- Published by Wiley in Journal of Turbomachinery
- Vol. 135 (3) , 031006
Large-Eddy Simulation With Zonal Near Wall Treatment of Flow and Heat Transfer in a Ribbed Duct for the Internal Cooling of Turbine Blades
Large eddy simulations of flow and heat transfer in a square ribbed duct with rib height to hydraulic diameter of 0.1 and 0.05 and rib pitch to rib height ratio of 10 and 20 are carried out with the near wall region being modeled with a zonal two layer model. A novel formulation is used for solving the turbulent boundary layer equation for the effective tangential velocity in a generalized co-ordinate system in the near wall zonal treatment. A methodology to model the heat transfer in the zonal near wall layer in the large eddy simulations (LES) framework is presented. This general approach is explained for both Dirichlet and Neumann wall boundary conditions. Reynolds numbers of 20,000 and 60,000 are investigated. Predictions with wall modeled LES are compared with the hydrodynamic and heat transfer experimental data of (Rau et al. 1998, “The Effect of Periodic Ribs on the Local Aerodynamic and Heat Transfer Performance of a Straight Cooling Channel,”ASME J. Turbomach., 120, pp. 368–375). and (Han et al. 1986, “Measurement of Heat Transfer and Pressure Drop in Rectangular Channels With Turbulence Promoters,” NASA Report No. 4015), and wall resolved LES data of Tafti (Tafti, 2004, “Evaluating the Role of Subgrid Stress Modeling in a Ribbed Duct for the Internal Cooling of Turbine Blades,” Int. J. Heat Fluid Flow 26, pp. 92–104). Friction factor, heat transfer coefficient, mean flow as well as turbulent statistics match available data closely with very good accuracy. Wall modeled LES at high Reynolds numbers as presented in this paper reduces the overall computational complexity by factors of 60–140 compared to resolved LES, without any significant loss in accuracy.
- 25 March 2013
- Published by Wiley in Journal of Turbomachinery
- Vol. 135 (3) , 031006
Large-Eddy Simulation With Zonal Near Wall Treatment of Flow and Heat Transfer in a Ribbed Duct for the Internal Cooling of Turbine Blades
Large eddy simulations of flow and heat transfer in a square ribbed duct with rib height to hydraulic diameter of 0.1 and 0.05 and rib pitch to rib height ratio of 10 and 20 are carried out with the near wall region being modeled with a zonal two layer model. A novel formulation is used for solving the turbulent boundary layer equation for the effective tangential velocity in a generalized co-ordinate system in the near wall zonal treatment. A methodology to model the heat transfer in the zonal near wall layer in the large eddy simulations (LES) framework is presented. This general approach is explained for both Dirichlet and Neumann wall boundary conditions. Reynolds numbers of 20,000 and 60,000 are investigated. Predictions with wall modeled LES are compared with the hydrodynamic and heat transfer experimental data of (Rau et al. 1998, “The Effect of Periodic Ribs on the Local Aerodynamic and Heat Transfer Performance of a Straight Cooling Channel,”ASME J. Turbomach., 120, pp. 368–375). and (Han et al. 1986, “Measurement of Heat Transfer and Pressure Drop in Rectangular Channels With Turbulence Promoters,” NASA Report No. 4015), and wall resolved LES data of Tafti (Tafti, 2004, “Evaluating the Role of Subgrid Stress Modeling in a Ribbed Duct for the Internal Cooling of Turbine Blades,” Int. J. Heat Fluid Flow 26, pp. 92–104). Friction factor, heat transfer coefficient, mean flow as well as turbulent statistics match available data closely with very good accuracy. Wall modeled LES at high Reynolds numbers as presented in this paper reduces the overall computational complexity by factors of 60–140 compared to resolved LES, without any significant loss in accuracy.
- 1 February 2012
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 50 (2) , 454-460
Two-Layer Wall Model for Large-Eddy Simulations of Flow over Rough Surfaces
- 1 February 2012
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 50 (2) , 454-460
Two-Layer Wall Model for Large-Eddy Simulations of Flow over Rough Surfaces
- 10 October 2010
- Published by ASME International
- p. 787-794
Study of Flow and Convective Heat Transfer in a Simulated Scaled Up Low Emission Annular Combustor
Modern Dry Low Emissions (DLE) combustors are characterized by highly swirling and expanding flows that makes the convective heat load on the gas side difficult to predict and estimate. A coupled experimental-numerical study of swirling flow inside a DLE annular combustor model is presented. A simulated scaled up annular combustor shell was designed with a generic fuel nozzle model to create the swirl in the flow. The experiment was simulated with a cold flow and heated combustor walls in a low speed wind tunnel. An infrared camera was used to obtain the temperature distribution along the liner wall. The experiment was conducted at various Reynolds numbers to investigate the effect on the convective heat transfer peak locations. A CFD study performed using FLUENT was used to get a better understanding of high swirl flow field and its effect on the heat transfer on liner walls. Results show that the heat transfer distributions in the annulus have slightly different characteristics for the concave and convex walls. Results also show a much slower drop in heat transfer coefficient enhancement with increasing Reynolds number compared to can combustor liner walls.
- 10 October 2010
- Published by ASME International
- p. 787-794
Study of Flow and Convective Heat Transfer in a Simulated Scaled Up Low Emission Annular Combustor
Modern Dry Low Emissions (DLE) combustors are characterized by highly swirling and expanding flows that makes the convective heat load on the gas side difficult to predict and estimate. A coupled experimental-numerical study of swirling flow inside a DLE annular combustor model is presented. A simulated scaled up annular combustor shell was designed with a generic fuel nozzle model to create the swirl in the flow. The experiment was simulated with a cold flow and heated combustor walls in a low speed wind tunnel. An infrared camera was used to obtain the temperature distribution along the liner wall. The experiment was conducted at various Reynolds numbers to investigate the effect on the convective heat transfer peak locations. A CFD study performed using FLUENT was used to get a better understanding of high swirl flow field and its effect on the heat transfer on liner walls. Results show that the heat transfer distributions in the annulus have slightly different characteristics for the concave and convex walls. Results also show a much slower drop in heat transfer coefficient enhancement with increasing Reynolds number compared to can combustor liner walls.