Ken-Ichi Matsuba
Ken-Ichi Matsuba has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Kenji Kamiyama
Japan Atom Energy Agcy, Fast Reactor Cycle Syst R&D Ctr, 4002 Narita Cho, Oarai, Ibaraki 3111393, Japan
2 shared publications - Mikio Isozaki
Japan Atomic Energy Agency
2 shared publications - Yoshiharu Tobita
Japan Atomic Energy Agency, 4002 Narita, Oarai, Ibaraki 311-1393, Japan
2 shared publications - Kai Igarashi
Department of Nuclear Engineering, Tokai University
1 shared publication Kenji Kamiyama
Oarai Research and Development Center, Japan Atomic Energy Agency, 4002 Narita, Oarai, Ibaraki, 311-1393, Japan
1 shared publicationKenji Kaymiyama
1 shared publication
Latest Publications
- 15 June 2026
- Published by The Japanese Society for Multiphase Flow in JAPANESE JOURNAL OF MULTIPHASE FLOW
- Vol. 40 (2) , 121-124
Sodium-Cooled Fast Reactor and Related Multiphase Flow Phenomena
Sodium-cooled fast reactors (SFRs) have merits of high natural circulation capacity thanks to high thermal conductivity of liquid sodium, and lower reactor pressure than that of lightwater reactors (LWR), near atmospheric pressure, making it easy to maintain the liquid level inside the reactor vessel (RV) even in the event of coolant leak, and making it less likely to reach the loss-of-coolant scenarios in LWR. On the other hand, SFRs have the characteristic that reactivity is introduced when coolant boiling or movement of core constituents occurs within the core. Therefore, in the event of a severe accident involving core meltdown, there is a possibility of recriticality leading to mechanical energy release. To avoid this possibility, a safety design involves installing flow paths within the core to rapidly discharge molten fuel from the core, as well as a core catcher at the bottom of the RV to retain it. It is believed that molten fuel discharged outside the core interacts with sodium, and as a result of this “molten fuel-sodium interaction,” the molten fuel solidifies into fine particles and accumulates on the core catcher. This paper presents the current status of assessment of molten fuel-sodium interactions in severe accidents.
- 15 June 2026
- Published by The Japanese Society for Multiphase Flow in JAPANESE JOURNAL OF MULTIPHASE FLOW
- Vol. 40 (2) , 121-124
Sodium-Cooled Fast Reactor and Related Multiphase Flow Phenomena
Sodium-cooled fast reactors (SFRs) have merits of high natural circulation capacity thanks to high thermal conductivity of liquid sodium, and lower reactor pressure than that of lightwater reactors (LWR), near atmospheric pressure, making it easy to maintain the liquid level inside the reactor vessel (RV) even in the event of coolant leak, and making it less likely to reach the loss-of-coolant scenarios in LWR. On the other hand, SFRs have the characteristic that reactivity is introduced when coolant boiling or movement of core constituents occurs within the core. Therefore, in the event of a severe accident involving core meltdown, there is a possibility of recriticality leading to mechanical energy release. To avoid this possibility, a safety design involves installing flow paths within the core to rapidly discharge molten fuel from the core, as well as a core catcher at the bottom of the RV to retain it. It is believed that molten fuel discharged outside the core interacts with sodium, and as a result of this “molten fuel-sodium interaction,” the molten fuel solidifies into fine particles and accumulates on the core catcher. This paper presents the current status of assessment of molten fuel-sodium interactions in severe accidents.
- Open Access
- 16 July 2021
- Published by ASME International
Validation of Analysis Models on Relocation Behavior of Molten Core Materials in Sodium-Cooled Fast Reactors Based on the Melt Discharge Experiment
In order to improve the safety of nuclear power plants, it is necessary to make sure measures against their severe accidents. Especially, in the case of a sodium-cooled fast reactor (SFR), there is a possibility of significant energy release due to formation of a large-scale molten fuel pool accompanied by re-criticality in the event of a core disruptive accident(CDA). It is
- 16 July 2021
- Published by ASME International
Open AccessValidation of Analysis Models on Relocation Behavior of Molten Core Materials in Sodium-Cooled Fast Reactors Based on the Melt Discharge Experiment
In order to improve the safety of nuclear power plants, it is necessary to make sure measures against their severe accidents. Especially, in the case of a sodium-cooled fast reactor (SFR), there is a possibility of significant energy release due to formation of a large-scale molten fuel pool accompanied by re-criticality in the event of a core disruptive accident(CDA). It is
- 10 December 2015
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 53 (5) , 707-712
Distance for fragmentation of a simulated molten-core material discharged into a sodium pool
A series of experiments has been carried out to obtain experimental knowledge on the distance for fragmentation of a molten core material discharged into the sodium plenum during postulated core disruptive accidents of sodium-cooled fast reactors. In the current experiments, 0.9 kg of molten aluminum (initial temperature: around 1473 K) was discharged into a sodium pool (diameter: 0.11 m, depth: 1 m, initial temperature: 673 K) through a nozzle (inner diameter: 20 mm). Visual observation of the fragmentation behavior was performed using an X-ray imaging system. The following experimental results were obtained. (1) Liquid column of molten aluminum was intensively fragmented almost simultaneously with a rapid expansion of sodium vapor in the vicinity of the column. (2) Due to the intensive fragmentation, penetration of the liquid column was limited to approximately 100 mm or so from the sodium level. (3) The molten aluminum was rapidly cooled after the intensive fragmentation. Based on these results, the distance for fragmentation of the liquid column was estimated to be 100 mm in the experiments. Through the current experiment, useful knowledge was obtained for the future development of an evaluation method of the distance for fragmentation of the molten core material.
- 10 December 2015
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 53 (5) , 707-712
Distance for fragmentation of a simulated molten-core material discharged into a sodium pool
A series of experiments has been carried out to obtain experimental knowledge on the distance for fragmentation of a molten core material discharged into the sodium plenum during postulated core disruptive accidents of sodium-cooled fast reactors. In the current experiments, 0.9 kg of molten aluminum (initial temperature: around 1473 K) was discharged into a sodium pool (diameter: 0.11 m, depth: 1 m, initial temperature: 673 K) through a nozzle (inner diameter: 20 mm). Visual observation of the fragmentation behavior was performed using an X-ray imaging system. The following experimental results were obtained. (1) Liquid column of molten aluminum was intensively fragmented almost simultaneously with a rapid expansion of sodium vapor in the vicinity of the column. (2) Due to the intensive fragmentation, penetration of the liquid column was limited to approximately 100 mm or so from the sodium level. (3) The molten aluminum was rapidly cooled after the intensive fragmentation. Based on these results, the distance for fragmentation of the liquid column was estimated to be 100 mm in the experiments. Through the current experiment, useful knowledge was obtained for the future development of an evaluation method of the distance for fragmentation of the molten core material.
- 1 January 2015
- Published by Japan Society of Mechanical Engineers in The Proceedings of the International Conference on Nuclear Engineering (ICONE)
- Vol. 2015.23, _ICONE23-1
ICONE23-1497 FIRST ANALYSIS OF LOCAL FUEL-COOLANT INTERACTIONS IN A MOLTEN POOL BY SIMMER-III USING REACTOR MATERIALS
Analyses of severe accidents for sodium-cooled fast reactors have shown that by assuming pessimistic conditions the accident might proceed into a transition phase where a large whole-core-scale pool containing sufficient fuel to exceed prompt criticality by fuel compaction might be formed. Local fuel-coolant interaction (FCI) in the pool is regarded as one of the probable initiators that could lead to such compactive fluid motions. To enhance the evaluation of severe accidents, a three-step research plan has been determined. In Phase 1, a series of simulated experiments, which covers a variety of conditions including much difference in water volume, melt temperature, water subcooling and water release site, was conducted by delivering a given quantity of water into a molten pool formed with a low-melting-point alloy, while in Phase 2, the interaction characteristics (esp. the pressure buildup) was investigated using the SIMMER-III, an advanced fast reactor safety analysis code. It was recognized that the SIMMER-III code, with its existing heat-transfer models, can reasonably reproduce the experimental evidence observed, thereby greatly stimulating us to initiate the Phase 3, in which further numerical analyses using reactor materials are planned. In this work, based on the latest calculations, it is confirmable that similar to the observations in Phases 1 and 2, for a given melt and sodium temperature within the non-film boiling condition, as the volume of sodium entrapped within the pool increases, a limited pressure-buildup is achievable. In addition, the performed analyses also suggest that despite of a comparatively larger temperature range of molten-fuel and sodium possibly varied during reactor accident progression, the isolation effect of vapor bubbles generated at the melt-sodium interface seems to be the unique dominant mechanism that leads to such limited pressurization. Knowledge and fundamental data from this work might be utilized for future empirical-approach studies (e.g. a lookup table for estimating the critical coolant volume required for achieving the saturated pressurization at varied melt and coolant temperatures).
- 1 January 2015
- Published by Japan Society of Mechanical Engineers in The Proceedings of the International Conference on Nuclear Engineering (ICONE)
- Vol. 2015.23, _ICONE23-1
ICONE23-1497 FIRST ANALYSIS OF LOCAL FUEL-COOLANT INTERACTIONS IN A MOLTEN POOL BY SIMMER-III USING REACTOR MATERIALS
Analyses of severe accidents for sodium-cooled fast reactors have shown that by assuming pessimistic conditions the accident might proceed into a transition phase where a large whole-core-scale pool containing sufficient fuel to exceed prompt criticality by fuel compaction might be formed. Local fuel-coolant interaction (FCI) in the pool is regarded as one of the probable initiators that could lead to such compactive fluid motions. To enhance the evaluation of severe accidents, a three-step research plan has been determined. In Phase 1, a series of simulated experiments, which covers a variety of conditions including much difference in water volume, melt temperature, water subcooling and water release site, was conducted by delivering a given quantity of water into a molten pool formed with a low-melting-point alloy, while in Phase 2, the interaction characteristics (esp. the pressure buildup) was investigated using the SIMMER-III, an advanced fast reactor safety analysis code. It was recognized that the SIMMER-III code, with its existing heat-transfer models, can reasonably reproduce the experimental evidence observed, thereby greatly stimulating us to initiate the Phase 3, in which further numerical analyses using reactor materials are planned. In this work, based on the latest calculations, it is confirmable that similar to the observations in Phases 1 and 2, for a given melt and sodium temperature within the non-film boiling condition, as the volume of sodium entrapped within the pool increases, a limited pressure-buildup is achievable. In addition, the performed analyses also suggest that despite of a comparatively larger temperature range of molten-fuel and sodium possibly varied during reactor accident progression, the isolation effect of vapor bubbles generated at the melt-sodium interface seems to be the unique dominant mechanism that leads to such limited pressurization. Knowledge and fundamental data from this work might be utilized for future empirical-approach studies (e.g. a lookup table for estimating the critical coolant volume required for achieving the saturated pressurization at varied melt and coolant temperatures).
- 21 February 2013
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 135 (3) , 032901
Mechanism of Upward Fuel Discharge During Core Disruptive Accidents in Sodium-Cooled Fast Reactors
The elimination of severe power excursion during core disruptive accidents is a key issue for the enhanced safety of sodium-cooled fast reactors. In order to prevent the formation of a large-scale molten fuel pool within a reactor core, which is one of the factors leading to the severe power excursion, the Japan Atomic Energy Agency (JAEA) is considering the introduction of fuel assembly with inner duct structure (FAIDUS). In the current reference design for FAIDUS, the top end of the inner duct is open, whereas the bottom end is closed, and therefore it is expected that the molten fuel will be discharged from the reactor core towards the upper sodium plenum through the inner duct. The objective of the present study is to clarify the fundamental mechanism for upward fuel discharge through the inner duct structure, and thereby to confirm the effectiveness of FAIDUS. The possibility of upward discharge of a high-density melt driven by coolant vapor has been confirmed by the JAEA's experiment, in which molten Wood's metal simulating the molten fuel was injected into a coolant channel (equivalent inner diameter: 30 mm, total height: 2 m, fluid content: water) simulating the inner duct structure. In this paper, the mechanism of upward discharge of a high-density melt driven by coolant vapor pressure and/or flow in this experiment is discussed in terms of the application to reactor conditions. Through this discussion, the following mechanisms were clarified. (1) Coolant vapor pressure is built up within the coolant channel after the melt injection. The magnitude of the pressure buildup becomes larger with the increase of melt-enthalpy-injection rate, which is defined by the product of melt-mass-injection rate into the coolant channel and melt specific enthalpy. (2) Following the pressure buildup, the melt is discharged upward, being driven by the coolant vapor flow directing towards the top opening end of the coolant channel. The upward discharge mass rate becomes higher with the increase of the magnitude of the pressure buildup and, therefore, the melt-enthalpy-injection rate. The experimental knowledge obtained from the JAEA's experiment suggests that the coolant pressure buildup could act as one of the driving forces for the upward discharge of a high-density melt through the inner duct structure in FAIDUS under reactor conditions with higher melt-enthalpy-injection rate than the current simulant experimental condition.
- 21 February 2013
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 135 (3) , 032901
Mechanism of Upward Fuel Discharge During Core Disruptive Accidents in Sodium-Cooled Fast Reactors
The elimination of severe power excursion during core disruptive accidents is a key issue for the enhanced safety of sodium-cooled fast reactors. In order to prevent the formation of a large-scale molten fuel pool within a reactor core, which is one of the factors leading to the severe power excursion, the Japan Atomic Energy Agency (JAEA) is considering the introduction of fuel assembly with inner duct structure (FAIDUS). In the current reference design for FAIDUS, the top end of the inner duct is open, whereas the bottom end is closed, and therefore it is expected that the molten fuel will be discharged from the reactor core towards the upper sodium plenum through the inner duct. The objective of the present study is to clarify the fundamental mechanism for upward fuel discharge through the inner duct structure, and thereby to confirm the effectiveness of FAIDUS. The possibility of upward discharge of a high-density melt driven by coolant vapor has been confirmed by the JAEA's experiment, in which molten Wood's metal simulating the molten fuel was injected into a coolant channel (equivalent inner diameter: 30 mm, total height: 2 m, fluid content: water) simulating the inner duct structure. In this paper, the mechanism of upward discharge of a high-density melt driven by coolant vapor pressure and/or flow in this experiment is discussed in terms of the application to reactor conditions. Through this discussion, the following mechanisms were clarified. (1) Coolant vapor pressure is built up within the coolant channel after the melt injection. The magnitude of the pressure buildup becomes larger with the increase of melt-enthalpy-injection rate, which is defined by the product of melt-mass-injection rate into the coolant channel and melt specific enthalpy. (2) Following the pressure buildup, the melt is discharged upward, being driven by the coolant vapor flow directing towards the top opening end of the coolant channel. The upward discharge mass rate becomes higher with the increase of the magnitude of the pressure buildup and, therefore, the melt-enthalpy-injection rate. The experimental knowledge obtained from the JAEA's experiment suggests that the coolant pressure buildup could act as one of the driving forces for the upward discharge of a high-density melt through the inner duct structure in FAIDUS under reactor conditions with higher melt-enthalpy-injection rate than the current simulant experimental condition.