IPIvan Popović

Ivan Popović

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ivan Popović has a total of 3 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Effects of a Parametric Variation of the Rim Seal Geometry on the Interaction Between Hub Leakage and Mainstream Flows in High Pressure Turbines

    by Ivan Popović, Howard P. Hodson

    The objective of this work was to assess and understand the effects of a parametric variation performed on a typical overlapping rim seal geometry. The datum geometry has been the focus of a detailed experimental investigation employing a large-scale linear cascade subjected to a range of the mass flow rates and swirl velocities of the leakage air. The parametric variations described in this paper were examined using validated computational fluid dynamics (CFD). As a part of the parametric studies, both the axial and the radial seal clearance between the rotor fin (angel wing) and stator platform were varied as well as the length of the overlap between stator and rotor platforms. In addition, the effects of forward and backward facing annulus steps were also investigated. It has been found that a backward-facing annulus step was detrimental for all conditions considered, while a forward-facing step offered improvements for smaller step heights and/or lower leakage fractions. Tightening of the seal clearances closer to the annulus line improved the sealing effectiveness but often at the expense of increased losses. On the other hand, increasing the overlap length led to improvements in the sealing effectiveness with very small effects on the overall losses. Moving the rim seal away from the blade-leading edges reduced the pressure asymmetry at the rim seal and increased the flow uniformity of the leakage air. However, this led to an increased cross-passage flow (more negative skew) and higher losses at all but lowest leakage fractions. The results presented in this paper highlight the fact that there may not be an optimum rim seal solution that would offer an improvement for the full range of leakage fractions and that, for different rim sealing flows, there may be a different optimum geometry. In addition, rotor disk movements in radial and axial directions at various off-design conditions should be considered as a part of the design process. Based on the presented results, it may be of a benefit to the turbine designer to consider rotor disk designs that would be more biased towards the upstream and outward disk movements, which would result in tightening of the seal clearances and avoidance of a backward-facing annulus step.


  • Improving Turbine Stage Efficiency and Sealing Effectiveness Through Modifications of the Rim Seal Geometry

    by Ivan Popovíc, Howard P. Hodson

    This paper presents an investigation of a range of engine realistic rim seals starting from a simple axial seal to different types of overlapping seals. The experiments were performed in a large-scale linear cascade equipped with a secondary air system capable of varying independently both the mass fraction as well as the swirl velocity of the leakage air. The experimental results were also complemented by computationally fluid dynamics (CFD) to provide better insight in the flow physics. It has been found that the key feature of the rim seals that affect their impact on overall loss generation and their ability to provide good sealing effectiveness was the location and the size of the recirculation zones within the rim seal. The requirements for good sealing and reduced spoiling effects on the main gaspath flow often led to contradictory designs. In general, the recirculation zones were found to improve sealing by reducing the effect of the pitchwise (circumferential) variation in the pressure distribution due to the blade's potential field, and thus reduce ingestion. However, at the same time the recirculation zones tend to increase the loss generation. The best compromise was found when the outer part of the seal and its interface with the rotor platform was as smooth as possible to minimize the spoiling losses, while the recirculation zones were confined to the inner part of the seal to maintain acceptable levels of sealing effectiveness. A new rim seal design, which utilizes the best attributes of the above mentioned designs was developed. Linear cascade tests showed the losses due to the leakage-mainstream interaction were reduced by 33% compared to the datum seal design. Further validation was performed by examining the new configuration using unsteady full-stage calculations under engine realistic conditions. These calculations suggest an improvement of nearly 0.2% in the stage efficiency.


  • The Effects of Unsteadiness and Compressibility on the Interaction Between Hub Leakage and Mainstream Flows in High-Pressure Turbines

    by Ivan Popović, Howard P. Hodson, Erik Janke, Torsten Wolf

    This paper investigates the effects of compressibility and unsteadiness due to the relative blade row motion and their importance in the interaction between hub leakage (purge) and mainstream flows. First, the challenges associated with the blade redesign for low-speed testing are described. The effects of Mach number are then addressed by analyzing the experiments in the low-speed linear cascade equipped with the secondary airflow system and computations performed on the low- and high-speed blade profiles. These results indicate that the compressibility does not significantly affect the interaction between the leakage and mainstream flows despite a number of compromises made during the design of the low-speed blade. This was due to the fact that the leakage–mainstream interaction takes place upstream of the blade throat where the local Mach numbers are still relatively low. The analysis is then extended to the equivalent full-stage unsteady computations. The periodic unsteadiness resulting from the relative motion of the upstream vanes appreciably affected the way in which the leakage flow is injected and the rotor flow field in general. However, the time-average flow field was still found to be dominated by the rotor blade's potential field. For the present test arrangement, the unsteady effects were not very detrimental and caused less than a 10% increase in the losses due to the leakage injection relative to the steady calculations.


  • Aerothermal Impact of the Interaction Between Hub Leakage and Mainstream Flows in Highly-Loaded High Pressure Turbine Blades

    by Ivan Popović, Howard P. Hodson

    This paper describes experimental and numerical investigations of a highly-loaded rotor blade with leakage (purge) flow injection through an upstream overlapping seal. The effects of both leakage mass flow rates and swirl have been studied to examine their effects on the aerothermal performance. As the leakage mass flow rate was increased, the loss generally increased. The increase in the losses was found to be nonlinear with the three distinct regimes of leakage-mainstream interaction being identified. The varying sensitivity of the losses to the leakage fraction was linked to the effects of the upstream potential field of the blade on a vortical structure originating from the outer part of the seal. This vortical structure affected the interaction between the leakage and mainstream flows as it grew to become the hub passage vortex. Very limited cooling was provided by the leakage flows. The coolant was mainly concentrated close to the suction surface in the front part of the rotor platform and on the blade suction surface in the path of the passage vortex. However, the regions benefiting from cooling were also characterized by higher values of the heat transfer coefficient. As a consequence, the net heat flux reduction was small, and the leakage injection was thus deemed thermally neutral.