Gaetano Corrado
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gaetano Corrado has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Fabrizia Caiazzo
Department of Industrial Engineering, University of Salerno, Via Giovanni Paolo II, 132, 84084 Fisciano, SA, Italy
4 shared publications - Vittorio Alfieri
Department of Industrial Engineering, University of Salerno, Via Giovanni Paolo II 132, 84084 Fisciano, Italy
3 shared publications - Paolo Argenio
University of Salerno
2 shared publications - Vincenzo Sergi
Dip. di Ingegneria Industriale, Università degli Studi di Salerno, Fisciano, Italy
2 shared publications Ernesto Mastrocinque
Univ. degli Studi di Salerno (Italy)
1 shared publication- Francesco Acerra
Leonardo Company SpA, Via dell’Aeronautica, 80038 Pomigliano d’Arco, Italy
1 shared publication
Latest Publications
- Open Access
- 1 August 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 93 (9-12) , 4023-4031
Laser powder-bed fusion of Inconel 718 to manufacture turbine blades
- 1 August 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 93 (9-12) , 4023-4031
Open AccessLaser powder-bed fusion of Inconel 718 to manufacture turbine blades
- Open Access
Laser Beam Welding of a Ti–6Al–4V Support Flange for Buy-to-Fly Reduction
Titanium and its alloys are increasingly being used in aerospace, although a number of issues must be addressed. Namely, in the framework of welding to produce complex parts, the same mechanical strength and a reduced buy-to-fly ratio are desired in comparison with the same components resulting from machining. To give grounds to actual application of autogenous laser beam welding, Ti–6Al–4V L- and T-joints have been investigated in this paper, as they are a common occurrence in general complex components. Discussions in terms of possible imperfections, microstructure, and microhardness have been conducted. Then, a real part consisting of a support flange for aerospace application has been chosen as a valuable test-article to be compared with its machined counterpart both in terms of strength and buy-to-fly. The feasibility and the effectiveness of the process are shown.
Open AccessLaser Beam Welding of a Ti–6Al–4V Support Flange for Buy-to-Fly Reduction
Titanium and its alloys are increasingly being used in aerospace, although a number of issues must be addressed. Namely, in the framework of welding to produce complex parts, the same mechanical strength and a reduced buy-to-fly ratio are desired in comparison with the same components resulting from machining. To give grounds to actual application of autogenous laser beam welding, Ti–6Al–4V L- and T-joints have been investigated in this paper, as they are a common occurrence in general complex components. Discussions in terms of possible imperfections, microstructure, and microhardness have been conducted. Then, a real part consisting of a support flange for aerospace application has been chosen as a valuable test-article to be compared with its machined counterpart both in terms of strength and buy-to-fly. The feasibility and the effectiveness of the process are shown.
- 18 November 2013
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 135 (6) , 061012
Investigation and Optimization of Laser Welding of Ti-6Al-4 V Titanium Alloy Plates
Titanium alloys are employed in a wide range of applications, from aerospace to medicine. In particular, Ti-6Al-4 V is the most common, thanks to an excellent combination of low density, high specific strength, and corrosion resistance. Laser welding has been increasingly considered as an alternative to traditional techniques to join titanium alloys. An increase in penetration depth and a reduction of possible welding defects are indeed achieved; moreover, a smaller grain size in the fused zone (FZ) is benefited in comparison to either tungsten inert gas (TIG) or plasma arc welding, thus improving the tensile strength of the welded structures. This study was carried out on 3 mm thick Ti-6Al-4 V plates in square butt welding configuration. The novelty element of the investigation is the use of a disk-laser source, which allows a number of benefits thanks to better beam quality; furthermore, a proper device was developed for bead protection, as titanium is prone to oxidation when in fused state. A three-level factorial plan was arranged in face-centered cubic scheme. The regression models were found for a number of crucial responses and the corresponding surfaces were discussed; then a numerical optimization was carried out. The suggested condition was evaluated to compare the actual responses to the predicted values; X-ray inspections, Vickers micro hardness tests, and tensile tests were performed for the optimum.
- 18 November 2013
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 135 (6) , 061012
Investigation and Optimization of Laser Welding of Ti-6Al-4 V Titanium Alloy Plates
Titanium alloys are employed in a wide range of applications, from aerospace to medicine. In particular, Ti-6Al-4 V is the most common, thanks to an excellent combination of low density, high specific strength, and corrosion resistance. Laser welding has been increasingly considered as an alternative to traditional techniques to join titanium alloys. An increase in penetration depth and a reduction of possible welding defects are indeed achieved; moreover, a smaller grain size in the fused zone (FZ) is benefited in comparison to either tungsten inert gas (TIG) or plasma arc welding, thus improving the tensile strength of the welded structures. This study was carried out on 3 mm thick Ti-6Al-4 V plates in square butt welding configuration. The novelty element of the investigation is the use of a disk-laser source, which allows a number of benefits thanks to better beam quality; furthermore, a proper device was developed for bead protection, as titanium is prone to oxidation when in fused state. A three-level factorial plan was arranged in face-centered cubic scheme. The regression models were found for a number of crucial responses and the corresponding surfaces were discussed; then a numerical optimization was carried out. The suggested condition was evaluated to compare the actual responses to the predicted values; X-ray inspections, Vickers micro hardness tests, and tensile tests were performed for the optimum.
- 1 June 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8433, 84330Y
Regression modeling to predict the geometrical features of Ti6Al4V thin sheets butt joints welded by disk laser
The aim of this work is to investigate the effects of power, welding speed, defocusing on geometric features and on defects of 1 mm Ti6Al4V laser welded butt joints by a new generation disk laser with 2 kW of maximum power. Them active gain is a Yb:YAG disk instead of traditional Nd:YAG rods. Disk geometry allows to keep the nominal beam quality also at high power because there is no thermal lensing effect, typical of rod geometry. A three level Box-Behnken experimental design with three repetitions is carried out for a total of 45 tests. Linear and quadratic regression equations are developed to relate the input factors to the output variables in order to predict the geometric features of butt joints.
- 1 June 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8433, 84330Y
Regression modeling to predict the geometrical features of Ti6Al4V thin sheets butt joints welded by disk laser
The aim of this work is to investigate the effects of power, welding speed, defocusing on geometric features and on defects of 1 mm Ti6Al4V laser welded butt joints by a new generation disk laser with 2 kW of maximum power. Them active gain is a Yb:YAG disk instead of traditional Nd:YAG rods. Disk geometry allows to keep the nominal beam quality also at high power because there is no thermal lensing effect, typical of rod geometry. A three level Box-Behnken experimental design with three repetitions is carried out for a total of 45 tests. Linear and quadratic regression equations are developed to relate the input factors to the output variables in order to predict the geometric features of butt joints.