Guy Littlefair
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Guy Littlefair has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Ashwin Polishetty
AUT: Auckland University of Technology
5 shared publications - Moshe Goldberg
School of Engineering, Deakin University, Geelong, Australia
5 shared publications - Amir Mahyar Khorasani
School of Engineering, Deakin University, Waurn Ponds 3216, Victoria, Australia
3 shared publications - Ian Gibson
Faculty of Engineering Technology, University of Twente, Enschede, the Netherlands
3 shared publications - Manikandakumar Shunmugavel
School of Engineering, Deakin University, Geelong, Australia
2 shared publications - Rajkumar Singh
Kalyani Centre for Technology and Innovation, Bharat Forge, Pune, India
2 shared publications
Latest Publications
- 17 October 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (6) , 1051-1056
A comparative study of mechanical properties and machinability of wrought and additive manufactured (selective laser melting) titanium alloy – Ti-6Al-4V
Purpose: The purpose of this paper is to study and compare the mechanical properties and machinability characteristics of additive manufactured titanium alloy Ti-6Al-4V with conventionally produced wrought titanium alloy,Ti-6Al-4V. The difference in mechanical properties such as yield strength, ultimate tensile strength, micro hardness, percentage of elongation and their effect on machinability characteristics like cutting forces and surface roughness are studied. It was found that higher strength and hardness of SLM Ti-6Al-4V compared to wrought Ti-6Al-4V owing to its peculiar acicular microstructure significantly affected the cutting forces and surface roughness. High cutting forces and low surface roughness were observed during machining of additive manufactured components compared to its wrought counterpart because of their difference in strength, hardness and ductility.Design/methodology/approach: Mechanical properties like yield strength, ultimate tensile strength, hardness and percentage of elongation and machinability characteristics like cutting forces and surface roughness were studied for both wrought and additive manufactured Ti-6Al-4V.Findings: Mechanical properties like yield strength, ultimate tensile strength and hardness were higher for additive manufactured components as compared to the wrought component. However additive manufactured components significantly lacked in ductility as compared to the wrought parts. Concerning machining, higher cutting forces and lower surface roughness were observed in additive manufactured Ti-6Al-4V compared to the wrought part as a result of differences in mechanical properties of these differently processed materials.Originality/value: This paper, for the first time, discusses the machining capabilities of additive manufactured Ti-6Al-4V.
- 17 October 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (6) , 1051-1056
A comparative study of mechanical properties and machinability of wrought and additive manufactured (selective laser melting) titanium alloy – Ti-6Al-4V
Purpose: The purpose of this paper is to study and compare the mechanical properties and machinability characteristics of additive manufactured titanium alloy Ti-6Al-4V with conventionally produced wrought titanium alloy,Ti-6Al-4V. The difference in mechanical properties such as yield strength, ultimate tensile strength, micro hardness, percentage of elongation and their effect on machinability characteristics like cutting forces and surface roughness are studied. It was found that higher strength and hardness of SLM Ti-6Al-4V compared to wrought Ti-6Al-4V owing to its peculiar acicular microstructure significantly affected the cutting forces and surface roughness. High cutting forces and low surface roughness were observed during machining of additive manufactured components compared to its wrought counterpart because of their difference in strength, hardness and ductility.Design/methodology/approach: Mechanical properties like yield strength, ultimate tensile strength, hardness and percentage of elongation and machinability characteristics like cutting forces and surface roughness were studied for both wrought and additive manufactured Ti-6Al-4V.Findings: Mechanical properties like yield strength, ultimate tensile strength and hardness were higher for additive manufactured components as compared to the wrought component. However additive manufactured components significantly lacked in ductility as compared to the wrought parts. Concerning machining, higher cutting forces and lower surface roughness were observed in additive manufactured Ti-6Al-4V compared to the wrought part as a result of differences in mechanical properties of these differently processed materials.Originality/value: This paper, for the first time, discusses the machining capabilities of additive manufactured Ti-6Al-4V.
- Open Access
Analysis of Thermal Stresses in Solidification of Spherical SLM Components
The majority of these machines fabricate from raw material in powder form using a directed energy beam to create a local melt zone. Total hip replacement is recommended for people who have medical issues related to excessive wear of the acetabular, osteoarthritis, accident or age. Researches have shown that large numbers of hip arthroplasties (where the articular surface of a musculoskeletal joint is replaced), hip remodelling, or realignment are carried out annually and will increase in the next few decades. Manufacturing of acetabular shells by using AM is a promising and emerging method that has a great potential to improve public health. Lost wax casting or investment casting is currently used to produce acetabular shells followed by lengthy and complex secondary processes such as machining and polishing. Living organs and medical models have intricate 3D shapes that are challenging to identity in X-ray CT images. These images are used for preparing treatment plans to improve the quality of the surgeries regarding waiting and surgery time per procedure and care regime. For instance, a limited number of hip replacement procedures can be carried out on each acetabulum due to a decrease of bone thickness. Rapid prototyping is a suitable treatment planning tool in complex cases to enhance the quality of surgical procedure and provide long-term stability that can be used to customize the shape and size of the acetabular shell. In this paper, to analyse the manufacturing of a prosthetic acetabular shell, built-up lines resulting from a thermal stress flow and process stopping during the selective laser melting (SLM) AM process, with regarding Gibbs free energy, interfacial energy, and equilibrium temperature will be discussed. Geometrical measurements showed 1.59% and 0.27% differences between the designed and manufactured prototype for inside and outside diameter respectively.
Open AccessAnalysis of Thermal Stresses in Solidification of Spherical SLM Components
The majority of these machines fabricate from raw material in powder form using a directed energy beam to create a local melt zone. Total hip replacement is recommended for people who have medical issues related to excessive wear of the acetabular, osteoarthritis, accident or age. Researches have shown that large numbers of hip arthroplasties (where the articular surface of a musculoskeletal joint is replaced), hip remodelling, or realignment are carried out annually and will increase in the next few decades. Manufacturing of acetabular shells by using AM is a promising and emerging method that has a great potential to improve public health. Lost wax casting or investment casting is currently used to produce acetabular shells followed by lengthy and complex secondary processes such as machining and polishing. Living organs and medical models have intricate 3D shapes that are challenging to identity in X-ray CT images. These images are used for preparing treatment plans to improve the quality of the surgeries regarding waiting and surgery time per procedure and care regime. For instance, a limited number of hip replacement procedures can be carried out on each acetabulum due to a decrease of bone thickness. Rapid prototyping is a suitable treatment planning tool in complex cases to enhance the quality of surgical procedure and provide long-term stability that can be used to customize the shape and size of the acetabular shell. In this paper, to analyse the manufacturing of a prosthetic acetabular shell, built-up lines resulting from a thermal stress flow and process stopping during the selective laser melting (SLM) AM process, with regarding Gibbs free energy, interfacial energy, and equilibrium temperature will be discussed. Geometrical measurements showed 1.59% and 0.27% differences between the designed and manufactured prototype for inside and outside diameter respectively.
- 20 March 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (2) , 295-304
On the role of different annealing heat treatments on mechanical properties and microstructure of selective laser melted and conventional wrought Ti-6Al-4V
Purpose: The purpose of this study was to conduct various heat treatments (HT) such as stress relief annealing, mill annealing, recrystallization (α + β) annealing and β annealing followed by furnace cooling (FC) that were implemented to determine the effect of these on mechanical properties and the microstructure of selective laser melted and wrought samples. The mentioned annealings have been carried out to achieve the related standards in the fabrication of surgery implants. Design/methodology/approach: In this paper, based on F2924-14 ASTM standard SLM and conventionally wrought parts were prepared. Then HT was performed and different characteristics such as microstructure, mechanical properties, macro-hardness and fracture surface for selective laser melted and wrought parts were analysed. Findings: The results show that the high cooling rate in selective laser melting (SLM) generates finer grains. Therefore, tensile strength and hardness increase along with a reduction in ductility was noticed. Recrystallization annealing appears to give the best combination of ductility, strength and hardness for selective laser melted parts, whilst for equivalent wrought samples, increasing HT temperature results in reduction of mechanical properties. Originality/value: The contributions of this paper are discussing the effect of different annealing on mechanical properties and microstructural evolution based on new ASTM standards for selective laser melted samples and comparing them with wrought parts.
- 20 March 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (2) , 295-304
On the role of different annealing heat treatments on mechanical properties and microstructure of selective laser melted and conventional wrought Ti-6Al-4V
Purpose: The purpose of this study was to conduct various heat treatments (HT) such as stress relief annealing, mill annealing, recrystallization (α + β) annealing and β annealing followed by furnace cooling (FC) that were implemented to determine the effect of these on mechanical properties and the microstructure of selective laser melted and wrought samples. The mentioned annealings have been carried out to achieve the related standards in the fabrication of surgery implants. Design/methodology/approach: In this paper, based on F2924-14 ASTM standard SLM and conventionally wrought parts were prepared. Then HT was performed and different characteristics such as microstructure, mechanical properties, macro-hardness and fracture surface for selective laser melted and wrought parts were analysed. Findings: The results show that the high cooling rate in selective laser melting (SLM) generates finer grains. Therefore, tensile strength and hardness increase along with a reduction in ductility was noticed. Recrystallization annealing appears to give the best combination of ductility, strength and hardness for selective laser melted parts, whilst for equivalent wrought samples, increasing HT temperature results in reduction of mechanical properties. Originality/value: The contributions of this paper are discussing the effect of different annealing on mechanical properties and microstructural evolution based on new ASTM standards for selective laser melted samples and comparing them with wrought parts.
- 16 January 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (1) , 110-121
Production of Ti-6Al-4V acetabular shell using selective laser melting: possible limitations in fabrication
Purpose: The purpose of this paper is to improve the manufacturing of a prosthetic acetabular shell by analyzing the main factors leading to failure during the selective laser melting (SLM) additive manufacturing (AM) process. Design/methodology/approach: Different computer-aided design and computer-aided manufacturing processes have been applied to fabricate acetabular parts. Then, various investigations into surface quality, mechanical properties and microstructure have been carried out to scrutinize the possible limitations in fabrication. Findings: Geometrical measurements showed 1.59 and 0.27 per cent differences between the designed and manufactured prototypes for inside and outside diameter, respectively. However, resulting studies showed that unstable surfaces, cracks, an interruption in powder delivery and low surface quality were the main problems that occurred during this process. These results indicate that SLM is an accurate and promising method for production of intricate shapes, provided that the appropriate settings of production conditions are considered to minimize possible limitations. Originality/value: The contributions of this paper are discussions covering different issues in the AM fabrication of acetabular shells to improve the mechanical properties, quality and durability of the produced parts.
- 16 January 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (1) , 110-121
Production of Ti-6Al-4V acetabular shell using selective laser melting: possible limitations in fabrication
Purpose: The purpose of this paper is to improve the manufacturing of a prosthetic acetabular shell by analyzing the main factors leading to failure during the selective laser melting (SLM) additive manufacturing (AM) process. Design/methodology/approach: Different computer-aided design and computer-aided manufacturing processes have been applied to fabricate acetabular parts. Then, various investigations into surface quality, mechanical properties and microstructure have been carried out to scrutinize the possible limitations in fabrication. Findings: Geometrical measurements showed 1.59 and 0.27 per cent differences between the designed and manufactured prototypes for inside and outside diameter, respectively. However, resulting studies showed that unstable surfaces, cracks, an interruption in powder delivery and low surface quality were the main problems that occurred during this process. These results indicate that SLM is an accurate and promising method for production of intricate shapes, provided that the appropriate settings of production conditions are considered to minimize possible limitations. Originality/value: The contributions of this paper are discussions covering different issues in the AM fabrication of acetabular shells to improve the mechanical properties, quality and durability of the produced parts.
- 1 January 2017
- Published by IGI Global Scientific Publishing in International Journal of Materials Forming and Machining Processes
- Vol. 4 (1) , 1-18
Effect of Microstructure on Chip Formation during Machining of Super Austenitic Stainless Steel
The AL6XN Super Austenitic Stainless Steel alloy is a commonly used steel in corrosive environments and tough applications. This paper aims to investigate the execution of a machining process on the AL6XN alloy. A wet machining process has been executed to machine the alloy under a combination of various cutting conditions using an up milling approach. Two cutting speeds, two cutting depths and two feeds were used. The outputs obtained and listed in this paper are the microstructure analysis, surface microhardness and the chip morphology. The microstructure of the AL6XN alloy was revealed using Electron Microscope and Electron Backscatter Diffraction (EBSD). Work hardening layer was located in the subsurface of the machined alloy. EBSD data assured that no phase transformation was occurred within the deformed microstructure due to machining. The chip cross-section was revealed to identify the presence of the shear bands and to calculate the alloy serration degree.
- 1 January 2017
- Published by IGI Global Scientific Publishing in International Journal of Materials Forming and Machining Processes
- Vol. 4 (1) , 1-18
Effect of Microstructure on Chip Formation during Machining of Super Austenitic Stainless Steel
The AL6XN Super Austenitic Stainless Steel alloy is a commonly used steel in corrosive environments and tough applications. This paper aims to investigate the execution of a machining process on the AL6XN alloy. A wet machining process has been executed to machine the alloy under a combination of various cutting conditions using an up milling approach. Two cutting speeds, two cutting depths and two feeds were used. The outputs obtained and listed in this paper are the microstructure analysis, surface microhardness and the chip morphology. The microstructure of the AL6XN alloy was revealed using Electron Microscope and Electron Backscatter Diffraction (EBSD). Work hardening layer was located in the subsurface of the machined alloy. EBSD data assured that no phase transformation was occurred within the deformed microstructure due to machining. The chip cross-section was revealed to identify the presence of the shear bands and to calculate the alloy serration degree.
- 1 January 2017
- Published by IGI Global Scientific Publishing
- p. 228-240
Tool Wear and Surface Integrity Analysis of Machined Heat Treated Selective Laser Melted Ti-6Al-4V
In this study, the tool wear and surface integrity during machining of wrought and Selective Laser Melted (SLM) titanium alloy (after heat treatment) are studied. Face turning trails were carried out on both the materials at different cutting speeds of 60,120 and 180 m/min. Cutting tools and machined specimens collected are characterized using scanning electron microscope, surface profiler and optical microscope to study the tool wear, machined surface quality and machining induced microstructural alterations. It was found that high cutting speeds lead to rapid tool wear during machining of SLM Ti-6Al-4V materials. Rapid tool wear observed at high cutting speeds in machining SLM Ti-6Al-4V resulted in damaging the surface integrity by 1) Deposition of chip/work material on the machined surface giving rise to higher surface roughness and 2) Increasing the depth of plastic deformation on the machined sub surface.
- 1 January 2017
- Published by IGI Global Scientific Publishing
- p. 228-240
Tool Wear and Surface Integrity Analysis of Machined Heat Treated Selective Laser Melted Ti-6Al-4V
In this study, the tool wear and surface integrity during machining of wrought and Selective Laser Melted (SLM) titanium alloy (after heat treatment) are studied. Face turning trails were carried out on both the materials at different cutting speeds of 60,120 and 180 m/min. Cutting tools and machined specimens collected are characterized using scanning electron microscope, surface profiler and optical microscope to study the tool wear, machined surface quality and machining induced microstructural alterations. It was found that high cutting speeds lead to rapid tool wear during machining of SLM Ti-6Al-4V materials. Rapid tool wear observed at high cutting speeds in machining SLM Ti-6Al-4V resulted in damaging the surface integrity by 1) Deposition of chip/work material on the machined surface giving rise to higher surface roughness and 2) Increasing the depth of plastic deformation on the machined sub surface.
- 1 October 2016
- Published by IGI Global Scientific Publishing in International Journal of Quality Assurance in Engineering and Technology Education
- Vol. 5 (4) , 1-11
Evaluating Student Perceptions in Peer to Peer Learning and Assessment Practices in Design Based Learning Environment
Considering the past decade, the changes involved in learning and teaching have been in terms of strategies, methods and practices to learning and teaching; assessment method; interface between a teacher and student; communication and feedback; self-reflective practices and designing pro-industry curriculum. For all the stakeholders involved, it becomes vital to know the student perception about the learning and teaching. The purpose of the paper is to evaluate the perception of the student experience on peer to peer learning and assessment. Issues related peer to peer learning has been identified based on the student response to a survey conducted at the end of the unit. The purpose of the paper is also to serve as a medium to contribute to the existing knowledge base on peer to peer learning and assessment in design/project based learning. The outcome of the paper is to review the existing literature, innovate a new approach and suggest a mutually acceptable solution to the issues related to peer to peer learning and assessment.
- 1 October 2016
- Published by IGI Global Scientific Publishing in International Journal of Quality Assurance in Engineering and Technology Education
- Vol. 5 (4) , 1-11
Evaluating Student Perceptions in Peer to Peer Learning and Assessment Practices in Design Based Learning Environment
Considering the past decade, the changes involved in learning and teaching have been in terms of strategies, methods and practices to learning and teaching; assessment method; interface between a teacher and student; communication and feedback; self-reflective practices and designing pro-industry curriculum. For all the stakeholders involved, it becomes vital to know the student perception about the learning and teaching. The purpose of the paper is to evaluate the perception of the student experience on peer to peer learning and assessment. Issues related peer to peer learning has been identified based on the student response to a survey conducted at the end of the unit. The purpose of the paper is also to serve as a medium to contribute to the existing knowledge base on peer to peer learning and assessment in design/project based learning. The outcome of the paper is to review the existing literature, innovate a new approach and suggest a mutually acceptable solution to the issues related to peer to peer learning and assessment.
- 1 July 2014
- Published by IGI Global Scientific Publishing in International Journal of Quality Assurance in Engineering and Technology Education
- Vol. 3 (3) , 110-121
Aligning Engineering Design Education with Accreditation Requirements
This paper focuses on aligning engineering design with accreditation requirements in engineering education. To be an accredited curriculum, education programs must incorporate graduate attributes required by program accrediting professional bodies. Graduate attributes are the required benchmarks for students to attain their specific qualities and abilities within a higher education institute. Most higher education institutions identify a list of expected graduate attributes or outcomes that are incorporated in their educational programs to be accredited by an accrediting professional body such as Engineers Australia (EA), Accreditation Board of Engineering and Technology (ABET) in the United States, and the European Accreditation of Engineering Programs (EUR-ACE) in Europe. This paper evaluates the program educational objectives, student outcomes, assessment methods and evaluation of different undergraduate engineering programs. It assesses how engineering design is practiced and incorporated as an important element of the graduate attributes through project oriented design based learning curriculum aligned with professional accreditation requirements.
- 1 July 2014
- Published by IGI Global Scientific Publishing in International Journal of Quality Assurance in Engineering and Technology Education
- Vol. 3 (3) , 110-121
Aligning Engineering Design Education with Accreditation Requirements
This paper focuses on aligning engineering design with accreditation requirements in engineering education. To be an accredited curriculum, education programs must incorporate graduate attributes required by program accrediting professional bodies. Graduate attributes are the required benchmarks for students to attain their specific qualities and abilities within a higher education institute. Most higher education institutions identify a list of expected graduate attributes or outcomes that are incorporated in their educational programs to be accredited by an accrediting professional body such as Engineers Australia (EA), Accreditation Board of Engineering and Technology (ABET) in the United States, and the European Accreditation of Engineering Programs (EUR-ACE) in Europe. This paper evaluates the program educational objectives, student outcomes, assessment methods and evaluation of different undergraduate engineering programs. It assesses how engineering design is practiced and incorporated as an important element of the graduate attributes through project oriented design based learning curriculum aligned with professional accreditation requirements.
- 1 January 2014
- Published by INSTICC
- p. 368-373
Robotic Grasping and Manipulation Controller Framework - Architecture Redevelopment
- 1 January 2014
- Published by INSTICC
- p. 368-373
Robotic Grasping and Manipulation Controller Framework - Architecture Redevelopment
- 6 December 2013
- Published by Springer Nature in Microsystem Technologies
- Vol. 21 (2) , 371-380
A protocol for improving fabrication yield of thin SU-8 microcantilevers for use in an aptasensor
- 6 December 2013
- Published by Springer Nature in Microsystem Technologies
- Vol. 21 (2) , 371-380
A protocol for improving fabrication yield of thin SU-8 microcantilevers for use in an aptasensor