Rajkumar Singh
Research Subjects
Research Interests
Rajkumar Singh has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ashwin Polishetty
AUT: Auckland University of Technology
2 shared publications - Guy Littlefair
School of Engineering, Deakin University, Geelong, Australia
2 shared publications - Manikandakumar Shunmugavel
School of Engineering, Deakin University, Geelong, Australia
2 shared publications - Moshe Goldberg
School of Engineering, Deakin University, Geelong, Australia
2 shared publications - Daniel Fabijanic
Institute for Frontier Materials, Deakin University, Geelong, Australia
1 shared publication - Manish Purushottam Meshram
Institute for Frontier Materials, Deakin University, Waurn Ponds, Australia
1 shared publication
Latest Publications
- 17 May 2024
- Published by Springer Nature in Transactions of the Indian National Academy of Engineering
- Vol. 9 (4) , 751-762
Influence of Cold Rolling and Direct Aging on Coarsening Kinetics of γ′ Precipitates and Hardness in UDIMET 720Li
- 17 May 2024
- Published by Springer Nature in Transactions of the Indian National Academy of Engineering
- Vol. 9 (4) , 751-762
Influence of Cold Rolling and Direct Aging on Coarsening Kinetics of γ′ Precipitates and Hardness in UDIMET 720Li
- 18 February 2023
- Published by Springer Nature in Metals and Materials International
- Vol. 29 (8) , 2216-2227
Development of Optimized Mechanical Properties of AISI 4340 Steel: Role of Quenching and Partitioning Process
- 18 February 2023
- Published by Springer Nature in Metals and Materials International
- Vol. 29 (8) , 2216-2227
Development of Optimized Mechanical Properties of AISI 4340 Steel: Role of Quenching and Partitioning Process
- 17 October 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (6) , 1051-1056
A comparative study of mechanical properties and machinability of wrought and additive manufactured (selective laser melting) titanium alloy – Ti-6Al-4V
Purpose: The purpose of this paper is to study and compare the mechanical properties and machinability characteristics of additive manufactured titanium alloy Ti-6Al-4V with conventionally produced wrought titanium alloy,Ti-6Al-4V. The difference in mechanical properties such as yield strength, ultimate tensile strength, micro hardness, percentage of elongation and their effect on machinability characteristics like cutting forces and surface roughness are studied. It was found that higher strength and hardness of SLM Ti-6Al-4V compared to wrought Ti-6Al-4V owing to its peculiar acicular microstructure significantly affected the cutting forces and surface roughness. High cutting forces and low surface roughness were observed during machining of additive manufactured components compared to its wrought counterpart because of their difference in strength, hardness and ductility.Design/methodology/approach: Mechanical properties like yield strength, ultimate tensile strength, hardness and percentage of elongation and machinability characteristics like cutting forces and surface roughness were studied for both wrought and additive manufactured Ti-6Al-4V.Findings: Mechanical properties like yield strength, ultimate tensile strength and hardness were higher for additive manufactured components as compared to the wrought component. However additive manufactured components significantly lacked in ductility as compared to the wrought parts. Concerning machining, higher cutting forces and lower surface roughness were observed in additive manufactured Ti-6Al-4V compared to the wrought part as a result of differences in mechanical properties of these differently processed materials.Originality/value: This paper, for the first time, discusses the machining capabilities of additive manufactured Ti-6Al-4V.
- 17 October 2017
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 23 (6) , 1051-1056
A comparative study of mechanical properties and machinability of wrought and additive manufactured (selective laser melting) titanium alloy – Ti-6Al-4V
Purpose: The purpose of this paper is to study and compare the mechanical properties and machinability characteristics of additive manufactured titanium alloy Ti-6Al-4V with conventionally produced wrought titanium alloy,Ti-6Al-4V. The difference in mechanical properties such as yield strength, ultimate tensile strength, micro hardness, percentage of elongation and their effect on machinability characteristics like cutting forces and surface roughness are studied. It was found that higher strength and hardness of SLM Ti-6Al-4V compared to wrought Ti-6Al-4V owing to its peculiar acicular microstructure significantly affected the cutting forces and surface roughness. High cutting forces and low surface roughness were observed during machining of additive manufactured components compared to its wrought counterpart because of their difference in strength, hardness and ductility.Design/methodology/approach: Mechanical properties like yield strength, ultimate tensile strength, hardness and percentage of elongation and machinability characteristics like cutting forces and surface roughness were studied for both wrought and additive manufactured Ti-6Al-4V.Findings: Mechanical properties like yield strength, ultimate tensile strength and hardness were higher for additive manufactured components as compared to the wrought component. However additive manufactured components significantly lacked in ductility as compared to the wrought parts. Concerning machining, higher cutting forces and lower surface roughness were observed in additive manufactured Ti-6Al-4V compared to the wrought part as a result of differences in mechanical properties of these differently processed materials.Originality/value: This paper, for the first time, discusses the machining capabilities of additive manufactured Ti-6Al-4V.
- 1 January 2017
- Published by IGI Global Scientific Publishing
- p. 228-240
Tool Wear and Surface Integrity Analysis of Machined Heat Treated Selective Laser Melted Ti-6Al-4V
In this study, the tool wear and surface integrity during machining of wrought and Selective Laser Melted (SLM) titanium alloy (after heat treatment) are studied. Face turning trails were carried out on both the materials at different cutting speeds of 60,120 and 180 m/min. Cutting tools and machined specimens collected are characterized using scanning electron microscope, surface profiler and optical microscope to study the tool wear, machined surface quality and machining induced microstructural alterations. It was found that high cutting speeds lead to rapid tool wear during machining of SLM Ti-6Al-4V materials. Rapid tool wear observed at high cutting speeds in machining SLM Ti-6Al-4V resulted in damaging the surface integrity by 1) Deposition of chip/work material on the machined surface giving rise to higher surface roughness and 2) Increasing the depth of plastic deformation on the machined sub surface.
- 1 January 2017
- Published by IGI Global Scientific Publishing
- p. 228-240
Tool Wear and Surface Integrity Analysis of Machined Heat Treated Selective Laser Melted Ti-6Al-4V
In this study, the tool wear and surface integrity during machining of wrought and Selective Laser Melted (SLM) titanium alloy (after heat treatment) are studied. Face turning trails were carried out on both the materials at different cutting speeds of 60,120 and 180 m/min. Cutting tools and machined specimens collected are characterized using scanning electron microscope, surface profiler and optical microscope to study the tool wear, machined surface quality and machining induced microstructural alterations. It was found that high cutting speeds lead to rapid tool wear during machining of SLM Ti-6Al-4V materials. Rapid tool wear observed at high cutting speeds in machining SLM Ti-6Al-4V resulted in damaging the surface integrity by 1) Deposition of chip/work material on the machined surface giving rise to higher surface roughness and 2) Increasing the depth of plastic deformation on the machined sub surface.