Carlos Bonilla
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Carlos Bonilla has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Kyle Gompertz
Department of Mechanical and Aerospace Engineering, Ohio State University, Columbus, Ohio 43235
2 shared publications- Ali Ameri
Aerospace Research Center, Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43235
1 shared publication - Brian P. Casaday1 shared publication
- Carey Clum1 shared publication
Chang-Joo Kim
Konkuk University
1 shared publicationJeffrey Bons
Ohio State University
1 shared publication
Latest Publications
- 24 October 2013
- Published by Wiley in Journal of Turbomachinery
- Vol. 136 (4) , 041017
Deposition With Hot Streaks in an Uncooled Turbine Vane Passage
The effect of hot streaks on deposition in a high pressure turbine vane passage was studied both experimentally and computationally. Modifications to Ohio State's Turbine Reaction Flow Rig allowed for the creation of simulated hot streaks in a four-vane annular cascade operating at temperatures up to 1093 °C. Total temperature surveys were made at the inlet plane of the vane passage, showing the variation caused by cold dilution jets. Deposition was generated by introducing sub-bituminous ash particles with a median diameter of 11.6 μm far upstream of the vane passage. Results indicate a strong correlation between surface deposits and the hot streak trajectory. A computational model was developed in Fluent to simulate both the flow and deposition. The flow solution was first obtained without particulates, and individual ash particles were subsequently introduced and tracked using a Lagrangian tracking model. The critical viscosity model was used to determine particle sticking upon impact with vane surfaces. Computational simulations confirm the migration of the hot streak and locations susceptible to enhanced deposition. Results show that the deposition model is overly sensitive to temperature and can severely overpredict deposition. Model constants can be tuned to better match experimental results but must be calibrated for each application.
- 24 October 2013
- Published by Wiley in Journal of Turbomachinery
- Vol. 136 (4) , 041017
Deposition With Hot Streaks in an Uncooled Turbine Vane Passage
The effect of hot streaks on deposition in a high pressure turbine vane passage was studied both experimentally and computationally. Modifications to Ohio State's Turbine Reaction Flow Rig allowed for the creation of simulated hot streaks in a four-vane annular cascade operating at temperatures up to 1093 °C. Total temperature surveys were made at the inlet plane of the vane passage, showing the variation caused by cold dilution jets. Deposition was generated by introducing sub-bituminous ash particles with a median diameter of 11.6 μm far upstream of the vane passage. Results indicate a strong correlation between surface deposits and the hot streak trajectory. A computational model was developed in Fluent to simulate both the flow and deposition. The flow solution was first obtained without particulates, and individual ash particles were subsequently introduced and tracked using a Lagrangian tracking model. The critical viscosity model was used to determine particle sticking upon impact with vane surfaces. Computational simulations confirm the migration of the hot streak and locations susceptible to enhanced deposition. Results show that the deposition model is overly sensitive to temperature and can severely overpredict deposition. Model constants can be tuned to better match experimental results but must be calibrated for each application.
- 1 May 2013
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 51 (5) , 1032-1041
Active Control of Flow Separation on a Laminar Airfoil
Detailed investigation of the NACA is obtained at a Reynolds number of and an angle of attack sweep of via particle image velocimetry and hot-film anemometry. The baseline flow is characterized by four distinct regimes, depending on angle of attack, with each exhibiting unique flow behavior. Active flow control via steady normal blowing is employed at four representative angles; blowing ratio (BR) is optimized by maximizing the lift coefficient with minimal power requirement. Suggestions are made with regard to the flow mechanisms whereby control is effective at each angle. A figure of merit is employed to quantify the efficiency of the actuation. The optimal BRs obtained at Reynolds number equal to are kept constant to observe the scalability of the control with respect to Reynolds number, ranging over nearly two orders of magnitude. It is observed that this approach is nonideal and that the BR should be optimized with Reynolds number as well. The optimization procedure is repeated for two angles of attack at a Reynolds number of . Lift enhancement is maintained while reducing the power requirement, thereby increasing the efficiency of the flow control.- 1 May 2013
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 51 (5) , 1032-1041
Active Control of Flow Separation on a Laminar Airfoil
Detailed investigation of the NACA is obtained at a Reynolds number of and an angle of attack sweep of via particle image velocimetry and hot-film anemometry. The baseline flow is characterized by four distinct regimes, depending on angle of attack, with each exhibiting unique flow behavior. Active flow control via steady normal blowing is employed at four representative angles; blowing ratio (BR) is optimized by maximizing the lift coefficient with minimal power requirement. Suggestions are made with regard to the flow mechanisms whereby control is effective at each angle. A figure of merit is employed to quantify the efficiency of the actuation. The optimal BRs obtained at Reynolds number equal to are kept constant to observe the scalability of the control with respect to Reynolds number, ranging over nearly two orders of magnitude. It is observed that this approach is nonideal and that the BR should be optimized with Reynolds number as well. The optimization procedure is repeated for two angles of attack at a Reynolds number of . Lift enhancement is maintained while reducing the power requirement, thereby increasing the efficiency of the flow control.