Brian P. Casaday
Research Subjects
Research Interests
Brian P. Casaday has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ali Ameri
Aerospace Research Center, Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43235
2 shared publications - Jeffrey P. Bons
Aerospace Research Center, Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43235
2 shared publications - Carey Clum1 shared publication
- Carlos Bonilla
Department of Mechanical and Aerospace Engineering, Ohio State University, Columbus, Ohio 43235
1 shared publication - Michael Lawrence1 shared publication
- Robin Prenter
Aerospace Research Center, The Ohio State University, Columbus, OH 43235
1 shared publication
Latest Publications
- 24 October 2013
- Published by Wiley in Journal of Turbomachinery
- Vol. 136 (4) , 041017
Deposition With Hot Streaks in an Uncooled Turbine Vane Passage
The effect of hot streaks on deposition in a high pressure turbine vane passage was studied both experimentally and computationally. Modifications to Ohio State's Turbine Reaction Flow Rig allowed for the creation of simulated hot streaks in a four-vane annular cascade operating at temperatures up to 1093 °C. Total temperature surveys were made at the inlet plane of the vane passage, showing the variation caused by cold dilution jets. Deposition was generated by introducing sub-bituminous ash particles with a median diameter of 11.6 μm far upstream of the vane passage. Results indicate a strong correlation between surface deposits and the hot streak trajectory. A computational model was developed in Fluent to simulate both the flow and deposition. The flow solution was first obtained without particulates, and individual ash particles were subsequently introduced and tracked using a Lagrangian tracking model. The critical viscosity model was used to determine particle sticking upon impact with vane surfaces. Computational simulations confirm the migration of the hot streak and locations susceptible to enhanced deposition. Results show that the deposition model is overly sensitive to temperature and can severely overpredict deposition. Model constants can be tuned to better match experimental results but must be calibrated for each application.
- 24 October 2013
- Published by Wiley in Journal of Turbomachinery
- Vol. 136 (4) , 041017
Deposition With Hot Streaks in an Uncooled Turbine Vane Passage
The effect of hot streaks on deposition in a high pressure turbine vane passage was studied both experimentally and computationally. Modifications to Ohio State's Turbine Reaction Flow Rig allowed for the creation of simulated hot streaks in a four-vane annular cascade operating at temperatures up to 1093 °C. Total temperature surveys were made at the inlet plane of the vane passage, showing the variation caused by cold dilution jets. Deposition was generated by introducing sub-bituminous ash particles with a median diameter of 11.6 μm far upstream of the vane passage. Results indicate a strong correlation between surface deposits and the hot streak trajectory. A computational model was developed in Fluent to simulate both the flow and deposition. The flow solution was first obtained without particulates, and individual ash particles were subsequently introduced and tracked using a Lagrangian tracking model. The critical viscosity model was used to determine particle sticking upon impact with vane surfaces. Computational simulations confirm the migration of the hot streak and locations susceptible to enhanced deposition. Results show that the deposition model is overly sensitive to temperature and can severely overpredict deposition. Model constants can be tuned to better match experimental results but must be calibrated for each application.
- 11 February 2013
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 135 (3) , 032001
Numerical Investigation of Ash Deposition on Nozzle Guide Vane Endwalls
A computational study was performed to determine the factors that affect ash deposition rates on the endwalls in a nozzle guide vane passage. Deposition tests were simulated in flow around a flat plate with a cylindrical leading edge, as well as through a modern, high-performance turbine vane passage. The flow solution was first obtained independent of the presence of particulates, and individual ash particles were subsequently tracked using a Lagrangian tracking model. Two turbulence models were applied, and their differences were discussed. The critical viscosity model was used to determine particle deposition. Features that contribute to endwall deposition, such as secondary flows, turbulent dispersion, or ballistic trajectories, were discussed, and deposition was quantified. Particle sizes were varied to reflect Stokes numbers ranging from 0.01 to 1.0 to determine the effect on endwall deposition. Results showed that endwall deposition rates can be as high as deposition on the leading edge for particles with a Stokes number less than 0.1, but endwall deposition rates for a Stokes number of 1.0 were less than 25% of the deposition rates on the leading edge or pressure surface of the turbine vane. Deposition rates on endwalls were largest near the leading edge stagnation region on both the cylinder and vane geometries, with significant deposition rates downstream showing a strong correlation to the secondary flows.
- 11 February 2013
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 135 (3) , 032001
Numerical Investigation of Ash Deposition on Nozzle Guide Vane Endwalls
A computational study was performed to determine the factors that affect ash deposition rates on the endwalls in a nozzle guide vane passage. Deposition tests were simulated in flow around a flat plate with a cylindrical leading edge, as well as through a modern, high-performance turbine vane passage. The flow solution was first obtained independent of the presence of particulates, and individual ash particles were subsequently tracked using a Lagrangian tracking model. Two turbulence models were applied, and their differences were discussed. The critical viscosity model was used to determine particle deposition. Features that contribute to endwall deposition, such as secondary flows, turbulent dispersion, or ballistic trajectories, were discussed, and deposition was quantified. Particle sizes were varied to reflect Stokes numbers ranging from 0.01 to 1.0 to determine the effect on endwall deposition. Results showed that endwall deposition rates can be as high as deposition on the leading edge for particles with a Stokes number less than 0.1, but endwall deposition rates for a Stokes number of 1.0 were less than 25% of the deposition rates on the leading edge or pressure surface of the turbine vane. Deposition rates on endwalls were largest near the leading edge stagnation region on both the cylinder and vane geometries, with significant deposition rates downstream showing a strong correlation to the secondary flows.