Honglei Bai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Honglei Bai has a total of 90 co-authors. Here are the top co-authors by number of shared publications:
- Mahbub Alam
Center for Turbulence Control, Harbin Institute of Technology (Shenzhen), Shenzhen 518055, China
10 shared publications - Nan Gao
Dalian University of Technology
4 shared publications - Shixiong Zhang
Sun Yat-Sen University, China
4 shared publications Weiguo Zhang
China Aerodynamics Research and Development Center, Mianyang, China
4 shared publications- Chunguang Xu
School of Aeronautics and Astronautics, Sun Yat-sen University, Shenzhen, China
3 shared publications - Fuwang Zhao
Department of Mechanical Engineering, The Hong Kong Polytechnic University 1 , Kowloon, Hong Kong, China
3 shared publications
Latest Publications
- 1 April 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (4)
Active control of flow over a pitching airfoil by leading-edge pulsation jets
This paper reports an experimental work on the active control of flow over a pitching NACA0012 airfoil model based on pulsation jets deployed at the leading edge. Reynolds number (Re) used is Re = 8 × 104, based on incoming freestream velocity (U∞) and chord length (c) of the airfoil model. Angle of attack (α) of the pitching airfoil model varies with time (t) in a sinusoidal function α(t) = αo + αmsin(2πft), where αo is the mean pitching angle, αm is the pitching amplitude, and f is the oscillation frequency. αo = 10°, αm = 15°, and f = 1.3 Hz (corresponding to a reduced ratio k = πfc/U∞ = 0.05) in this work. The pulsation jets at the leading edge are oriented at 45° with respect to the airfoil chord line and involve several control parameters, including momentum coefficient Cμ (= 0%–1.05%), non-dimensional pulsation frequency Fj* (= 0–0.91), and duty cycle DC (= 30%–50%). While aerodynamic forces on the airfoil model are measured by a load cell, flow fields over the airfoil model are captured via phase-locked particle image velocimetry technique. Results from force measurements indicate that lift coefficient of the airfoil model can be significantly enhanced by the pulsation jets after dynamic stall in the upstroke and in the entire downstroke, leading to a large reduction (up to 40%) of the hysteresis loop. Based on thorough examinations of instantaneous and phase-averaged flows and analyses of proper orthogonal decomposition, remarkable changes in the flow fields are observed in the presence of the pulsation jets, compared with those in the absence of perturbations. It is revealed that large-scale dynamic stall vortices from the pitching airfoil model are disturbed by small-scale coherent vortices induced by the pulsation jets. Moreover, an optimal pulsation frequency Fj* = 0.46 is identified, corresponding to the convection time of these vortices from the leading to trailing edges.
- 1 April 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (4)
Active control of flow over a pitching airfoil by leading-edge pulsation jets
This paper reports an experimental work on the active control of flow over a pitching NACA0012 airfoil model based on pulsation jets deployed at the leading edge. Reynolds number (Re) used is Re = 8 × 104, based on incoming freestream velocity (U∞) and chord length (c) of the airfoil model. Angle of attack (α) of the pitching airfoil model varies with time (t) in a sinusoidal function α(t) = αo + αmsin(2πft), where αo is the mean pitching angle, αm is the pitching amplitude, and f is the oscillation frequency. αo = 10°, αm = 15°, and f = 1.3 Hz (corresponding to a reduced ratio k = πfc/U∞ = 0.05) in this work. The pulsation jets at the leading edge are oriented at 45° with respect to the airfoil chord line and involve several control parameters, including momentum coefficient Cμ (= 0%–1.05%), non-dimensional pulsation frequency Fj* (= 0–0.91), and duty cycle DC (= 30%–50%). While aerodynamic forces on the airfoil model are measured by a load cell, flow fields over the airfoil model are captured via phase-locked particle image velocimetry technique. Results from force measurements indicate that lift coefficient of the airfoil model can be significantly enhanced by the pulsation jets after dynamic stall in the upstroke and in the entire downstroke, leading to a large reduction (up to 40%) of the hysteresis loop. Based on thorough examinations of instantaneous and phase-averaged flows and analyses of proper orthogonal decomposition, remarkable changes in the flow fields are observed in the presence of the pulsation jets, compared with those in the absence of perturbations. It is revealed that large-scale dynamic stall vortices from the pitching airfoil model are disturbed by small-scale coherent vortices induced by the pulsation jets. Moreover, an optimal pulsation frequency Fj* = 0.46 is identified, corresponding to the convection time of these vortices from the leading to trailing edges.
- 21 March 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 176
A Cartesian grid based non-equilibrium wall model for RANS simulation of high Reynolds number turbulent flows
- 21 March 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 176
A Cartesian grid based non-equilibrium wall model for RANS simulation of high Reynolds number turbulent flows
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Flow over a bio-inspired wavy elliptic cylinder at a subcritical Reynolds number of 3 × 103
The unique morphology of seal whiskers can significantly reduce drag and fluctuating lift forces. Inspired by this, large eddy simulations and water tunnel experiments of the flow around a seal-whisker-inspired, simplified wavy elliptic cylinder are conducted at a subcritical Reynolds number of Re = 3 × 103. The spanwise wavelength (λ) of the wavy elliptic cylinder covers a wide range of 0.5 ≤ λ/Dm ≤ 8, with a fixed wave amplitude of a/Dm = 0.1, where Dm is the mean hydrodynamic diameter of the wavy elliptic cylinder. Based on variations with λ/Dm in time-mean drag, fluctuating lift, Strouhal number, vortex formation length, and wake topology, the flow around the wavy elliptic cylinder is classified into four distinct regimes, i.e., I–IV. A comprehensive examination is made for each regime, including instantaneous and time-mean flows, Reynolds stresses, and turbulent kinetic energy distributions. Results indicate that, compared to the baseline straight elliptic cylinder, the wavy elliptic cylinders with λ/Dm = 3 and 4 in flow regime II can reduce time-mean drag and fluctuating lift by 12.5% and 86.6%, respectively; meanwhile, significant force reductions are observed in flow regimes III and IV. The performance is associated with the emergence of hairpin-like vortices in instantaneous flows, significant increases in vortex formation length, distinct flow bifurcations, and substantial reductions in Reynolds stresses and turbulent kinetic energy in the near wake. It is also noted that, similar to the wavy circular cylinder, the spanwise variation rate of the vortex formation length of the wavy elliptic cylinder is a key parameter influencing the near wake flow.
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Flow over a bio-inspired wavy elliptic cylinder at a subcritical Reynolds number of 3 × 103
The unique morphology of seal whiskers can significantly reduce drag and fluctuating lift forces. Inspired by this, large eddy simulations and water tunnel experiments of the flow around a seal-whisker-inspired, simplified wavy elliptic cylinder are conducted at a subcritical Reynolds number of Re = 3 × 103. The spanwise wavelength (λ) of the wavy elliptic cylinder covers a wide range of 0.5 ≤ λ/Dm ≤ 8, with a fixed wave amplitude of a/Dm = 0.1, where Dm is the mean hydrodynamic diameter of the wavy elliptic cylinder. Based on variations with λ/Dm in time-mean drag, fluctuating lift, Strouhal number, vortex formation length, and wake topology, the flow around the wavy elliptic cylinder is classified into four distinct regimes, i.e., I–IV. A comprehensive examination is made for each regime, including instantaneous and time-mean flows, Reynolds stresses, and turbulent kinetic energy distributions. Results indicate that, compared to the baseline straight elliptic cylinder, the wavy elliptic cylinders with λ/Dm = 3 and 4 in flow regime II can reduce time-mean drag and fluctuating lift by 12.5% and 86.6%, respectively; meanwhile, significant force reductions are observed in flow regimes III and IV. The performance is associated with the emergence of hairpin-like vortices in instantaneous flows, significant increases in vortex formation length, distinct flow bifurcations, and substantial reductions in Reynolds stresses and turbulent kinetic energy in the near wake. It is also noted that, similar to the wavy circular cylinder, the spanwise variation rate of the vortex formation length of the wavy elliptic cylinder is a key parameter influencing the near wake flow.
- 7 September 2025
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 115
Flow over airfoil model covered by bio-inspired herringbone riblets
- 7 September 2025
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 115
Flow over airfoil model covered by bio-inspired herringbone riblets
- 20 August 2025
- Published by Springer Nature in Engineering with Computers
- Vol. 41 (5) , 3871-3889
A novel SPH-based efficient adaptive quadrilateral-dominant mesh generation method
- 20 August 2025
- Published by Springer Nature in Engineering with Computers
- Vol. 41 (5) , 3871-3889
A novel SPH-based efficient adaptive quadrilateral-dominant mesh generation method
- Retracted
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Corrugated airfoils for enhanced low-speed aerodynamics: A bio-inspired review
Inspired by dragonfly wings, corrugated airfoils offer promising solutions for low-speed aviation and marine applications. These airfoils provide passive flow control, enhancing lift, delaying stall, and reducing drag at low Reynolds numbers, which is not achievable by traditional smooth airfoils. The review synthesizes findings from experimental and computational studies, examining the influence of Reynolds number and boundary conditions on corrugated airfoil performance. The corrugation-generated vortices stabilize flow, minimizing separation and turbulence. Applications in aviation, marine engineering, and renewable energy are discussed, emphasizing the potential of corrugated airfoils to revolutionize efficiency and control. By addressing existing limitations and proposing future research directions, this review highlights the significance of biomimicry in developing advanced fluid dynamic systems for transport, surveillance, and energy. While manufacturing complexities and computational costs remain challenges, this review bridges biological and engineering design, fostering sustainable and efficient aerodynamics and technological advancements.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
RetractedCorrugated airfoils for enhanced low-speed aerodynamics: A bio-inspired review
Inspired by dragonfly wings, corrugated airfoils offer promising solutions for low-speed aviation and marine applications. These airfoils provide passive flow control, enhancing lift, delaying stall, and reducing drag at low Reynolds numbers, which is not achievable by traditional smooth airfoils. The review synthesizes findings from experimental and computational studies, examining the influence of Reynolds number and boundary conditions on corrugated airfoil performance. The corrugation-generated vortices stabilize flow, minimizing separation and turbulence. Applications in aviation, marine engineering, and renewable energy are discussed, emphasizing the potential of corrugated airfoils to revolutionize efficiency and control. By addressing existing limitations and proposing future research directions, this review highlights the significance of biomimicry in developing advanced fluid dynamic systems for transport, surveillance, and energy. While manufacturing complexities and computational costs remain challenges, this review bridges biological and engineering design, fostering sustainable and efficient aerodynamics and technological advancements.
- 25 July 2025
- Published by Springer Nature in Acta Mechanica Sinica
- Vol. 42 (3) , 1-23
Simultaneous time-resolved PIV measurements of two orthogonal planes in a flat-plate turbulent boundary layer at moderate Reynolds numbers
- 25 July 2025
- Published by Springer Nature in Acta Mechanica Sinica
- Vol. 42 (3) , 1-23
Simultaneous time-resolved PIV measurements of two orthogonal planes in a flat-plate turbulent boundary layer at moderate Reynolds numbers
- Open Access
- 29 May 2025
- Published by Springer Nature in Research Square
A Novel SPH-Based Efficient Adaptive Quadrilateral-Dominant Mesh Generation Method
In this paper, we introduce a novel, SPH-based(Smoothed Particle Hydrodynamics), parallel adaptive quadrilateral-dominated mesh generation method. Building upon particle-based mesh generation techniques, we propose an innovative Adaptive Smoothing Length Smoothed Particle Hydrodynamics (ASL-SPH) Method utilizing the L ∞ norm metric to enhance particle relaxation. The core concept leverages the square characteristic of the L ∞ norm's unit circle to facilitate the construction of high-quality quadrilateral meshes. The algorithm comprises three primary stages: (1) computation of the initial adaptive particle distribution based on target size and density fields; (2) GPU-accelerated particle relaxation guided by a direction field, employing the proposed ASL-SPH grounded in the L ∞ norm metric; and (3) establishment of topological connections among particles to generate a quadrilateral-dominated mesh. Numerical experiments validate that the proposed method effectively generates high-quality quadrilateral-dominated meshes under complex boundary conditions. Furthermore, the integration of GPU parallel computing significantly enhances the algorithm's efficiency.
- 29 May 2025
- Published by Springer Nature in Research Square
Open AccessA Novel SPH-Based Efficient Adaptive Quadrilateral-Dominant Mesh Generation Method
In this paper, we introduce a novel, SPH-based(Smoothed Particle Hydrodynamics), parallel adaptive quadrilateral-dominated mesh generation method. Building upon particle-based mesh generation techniques, we propose an innovative Adaptive Smoothing Length Smoothed Particle Hydrodynamics (ASL-SPH) Method utilizing the L ∞ norm metric to enhance particle relaxation. The core concept leverages the square characteristic of the L ∞ norm's unit circle to facilitate the construction of high-quality quadrilateral meshes. The algorithm comprises three primary stages: (1) computation of the initial adaptive particle distribution based on target size and density fields; (2) GPU-accelerated particle relaxation guided by a direction field, employing the proposed ASL-SPH grounded in the L ∞ norm metric; and (3) establishment of topological connections among particles to generate a quadrilateral-dominated mesh. Numerical experiments validate that the proposed method effectively generates high-quality quadrilateral-dominated meshes under complex boundary conditions. Furthermore, the integration of GPU parallel computing significantly enhances the algorithm's efficiency.
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Large-scale and very-large-scale motions in a moderate-Reynolds-number turbulent boundary layer over a flat plate towed in a tank
An experimental work is conducted to investigate large-scale motions (LSMs) and very-large-scale motions (VLSMs) of a turbulent boundary layer generated by a flat plate towed in a tank. Reynolds number based on friction velocity and boundary layer thickness covers a range of 1200 ≤Reτ≤ 3100. The streamwise–wall-normal plane and the streamwise–spanwise plane are separately measured using time-resolved stereoscopic particle image velocimetry (TR-SPIV) and time-resolved planar PIV (TR-PIV), respectively. The large-scale coherent structures in the two orthogonal planes are identified by the clustering method. Based on spatiotemporal evolutions of instantaneous flow fields, it is observed that low- and high-speed coherent structures collide and lean against each other, generating a strong shear layer between them. The low-speed coherent structures move away from the wall, while the high-speed coherent structures travel toward the wall near the interaction regions during the shearing, which may lead to merging and splitting of the coherent structures. The coherent structures grow in streamwise scales by self-stretching and coalescence with adjacent coherent structures. The properties of the LSMs and VLSMs, including scales, inclination angles, meandering behaviors, and contributions of high- or low-speed VLSMs to skin friction, are quantitatively examined. Furthermore, the dynamic characteristics of the LSMs and VLSMs are classified into merging, splitting, growing, and shortening, with occurrence frequencies independent of Reynolds number. Effects of shearing on the merging and splitting events are discussed. Results from this work suggest that the primary formation mechanism of the VLSMs is the self-growing of LSMs vigorously stretching along the streamwise direction.
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Large-scale and very-large-scale motions in a moderate-Reynolds-number turbulent boundary layer over a flat plate towed in a tank
An experimental work is conducted to investigate large-scale motions (LSMs) and very-large-scale motions (VLSMs) of a turbulent boundary layer generated by a flat plate towed in a tank. Reynolds number based on friction velocity and boundary layer thickness covers a range of 1200 ≤Reτ≤ 3100. The streamwise–wall-normal plane and the streamwise–spanwise plane are separately measured using time-resolved stereoscopic particle image velocimetry (TR-SPIV) and time-resolved planar PIV (TR-PIV), respectively. The large-scale coherent structures in the two orthogonal planes are identified by the clustering method. Based on spatiotemporal evolutions of instantaneous flow fields, it is observed that low- and high-speed coherent structures collide and lean against each other, generating a strong shear layer between them. The low-speed coherent structures move away from the wall, while the high-speed coherent structures travel toward the wall near the interaction regions during the shearing, which may lead to merging and splitting of the coherent structures. The coherent structures grow in streamwise scales by self-stretching and coalescence with adjacent coherent structures. The properties of the LSMs and VLSMs, including scales, inclination angles, meandering behaviors, and contributions of high- or low-speed VLSMs to skin friction, are quantitatively examined. Furthermore, the dynamic characteristics of the LSMs and VLSMs are classified into merging, splitting, growing, and shortening, with occurrence frequencies independent of Reynolds number. Effects of shearing on the merging and splitting events are discussed. Results from this work suggest that the primary formation mechanism of the VLSMs is the self-growing of LSMs vigorously stretching along the streamwise direction.
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Optimization control of the D-shaped cylinder flow with genetic algorithm and Coanda pulsation jets
Flow around the D-shaped cylinder is one of the basic models in aerospace, civil, and marine engineering applications. This paper reports an experimental work on the optimization control of the D-shaped cylinder flow using genetic algorithm (GA) and Coanda pulsation jets. Experiments are conducted in a wind tunnel at a Reynolds number Re = 2.0 × 104, based on free stream velocity U∞ and the cylinder height H. The Coanda pulsation jets are realized by issuing pulsation jets over the surface of a one-quarter cylinder (radius r = 0.2H), which is attached on the base and near the trailing edge of the D-shaped cylinder. Control parameters of the Coanda pulsation jets include momentum coefficient (Cμ), nondimensional pulsation frequency (fj*), duty cycle (DC), and phase shift (Δϕ) between the lower and upper jets. GA is adopted to seek optimal working parameters of the Coanda pulsation jets for the maximum recovery of base pressure (indicating drag reduction). The near wake flow of the D-shaped cylinder under optimal control is measured using particle image velocimetry, and then, thoroughly examined using proper orthogonal decomposition (POD), to investigate underlying mechanisms of drag reduction. Two sets of optimal control parameters differing in fj* and Δϕ are identified by the GA-based optimization control, corresponding to the maximum base pressure recovery of 40.7%–43.3%. Significant modifications in the near wake flows are observed in the presence of the optimal control, based on instantaneous, time-mean and phase-averaged flow structures, Reynolds stresses, as well as the POD analyses. It is found that the Coanda pulsation jets working at the different sets of optimal parameters render distinct perturbations to the near wake flows, weakening the large-scale Karman vortices while energizing the small-scale structures.
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Optimization control of the D-shaped cylinder flow with genetic algorithm and Coanda pulsation jets
Flow around the D-shaped cylinder is one of the basic models in aerospace, civil, and marine engineering applications. This paper reports an experimental work on the optimization control of the D-shaped cylinder flow using genetic algorithm (GA) and Coanda pulsation jets. Experiments are conducted in a wind tunnel at a Reynolds number Re = 2.0 × 104, based on free stream velocity U∞ and the cylinder height H. The Coanda pulsation jets are realized by issuing pulsation jets over the surface of a one-quarter cylinder (radius r = 0.2H), which is attached on the base and near the trailing edge of the D-shaped cylinder. Control parameters of the Coanda pulsation jets include momentum coefficient (Cμ), nondimensional pulsation frequency (fj*), duty cycle (DC), and phase shift (Δϕ) between the lower and upper jets. GA is adopted to seek optimal working parameters of the Coanda pulsation jets for the maximum recovery of base pressure (indicating drag reduction). The near wake flow of the D-shaped cylinder under optimal control is measured using particle image velocimetry, and then, thoroughly examined using proper orthogonal decomposition (POD), to investigate underlying mechanisms of drag reduction. Two sets of optimal control parameters differing in fj* and Δϕ are identified by the GA-based optimization control, corresponding to the maximum base pressure recovery of 40.7%–43.3%. Significant modifications in the near wake flows are observed in the presence of the optimal control, based on instantaneous, time-mean and phase-averaged flow structures, Reynolds stresses, as well as the POD analyses. It is found that the Coanda pulsation jets working at the different sets of optimal parameters render distinct perturbations to the near wake flows, weakening the large-scale Karman vortices while energizing the small-scale structures.