Herbert Reichl
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Herbert Reichl has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- C. Kallmayer
Res. Center of Microperipheric Technol., Technische Univ. Berlin, Germany
3 shared publications R. Aschenbrenner
Res. Center of Microperipheric Technol., Technische Univ. Berlin, Germany
3 shared publicationsB. Pahl
Res. Center of Microperipheric Technol., Technische Univ. Berlin, Germany
2 shared publications- David Dimitry Polityko
Technical University Berlin, FSP Mikroperipherik (TUB-MP), Gustav-Meyer-Allee 25, D-13355, Berlin, Germany
2 shared publications H. Oppermann
Fraunhofer IZM, Univ. of Bonn, Berlin, Germany
2 shared publicationsJ. Wolf
Fraunhofer IZM, Univ. of Bonn, Berlin, Germany
2 shared publications
Latest Publications
- 1 December 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 609-612
Printing Solder Paste in Dry Film - A Low Cost Fine-Pitch Bumping Technique
There is a steady trend to decrease bump pitch and the total cost for the bumping process. Several techniques for bumping are available such as screen printing of solder paste through metal stencils, electroplating of bumps, ball placement or C4NP. Initially there appears to be a number of choices for bumping, however after looking at the details the choices are significantly reduced. The use of ball placement or screen printing is limited to larger sized bumps and coarser pitches. Bumping by electroplating which is popular for fine-pitch bumping is restricted to single or double component systems. Electroplating of triple component systems like SnAgCu which are interesting for lead free bumping requires a very complex process monitoring. Additionally, electroplating of ternary metal systems is not yet suitable for manufacturing. In this paper the basic process steps for a different bumping technology are discussed in detail. This technology uses a solder paste which is printed into photo-structured dry film. Test wafers with Ni + flash-Au final metallisation were provided. A dry film photo resist was laminated onto the wafers, exposed and developed. Next, solder paste was printed into the structured resist. The wafers were then passed through a Pb-free reflow profile. After the reflow, the dry film was successfully stripped. A variation of pad size and resist openings were investigated. Correlation between design and results are discussed.
- 1 December 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 609-612
Printing Solder Paste in Dry Film - A Low Cost Fine-Pitch Bumping Technique
There is a steady trend to decrease bump pitch and the total cost for the bumping process. Several techniques for bumping are available such as screen printing of solder paste through metal stencils, electroplating of bumps, ball placement or C4NP. Initially there appears to be a number of choices for bumping, however after looking at the details the choices are significantly reduced. The use of ball placement or screen printing is limited to larger sized bumps and coarser pitches. Bumping by electroplating which is popular for fine-pitch bumping is restricted to single or double component systems. Electroplating of triple component systems like SnAgCu which are interesting for lead free bumping requires a very complex process monitoring. Additionally, electroplating of ternary metal systems is not yet suitable for manufacturing. In this paper the basic process steps for a different bumping technology are discussed in detail. This technology uses a solder paste which is printed into photo-structured dry film. Test wafers with Ni + flash-Au final metallisation were provided. A dry film photo resist was laminated onto the wafers, exposed and developed. Next, solder paste was printed into the structured resist. The wafers were then passed through a Pb-free reflow profile. After the reflow, the dry film was successfully stripped. A variation of pad size and resist openings were investigated. Correlation between design and results are discussed.
- 1 December 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 623-630
Technology Aware Modeling of 2.5D-SiP for Automation in Physical Design
The vertical integration within the system-in-package (SiP) approach is becoming more and more important. While system-on-ohip (SoC) and PCB design teams are operating with highly developed EDA tools, there is a lack of automation tools for the design of SiP. This is particularly true for the engineering of so called 2.5D SiP, which integrate heterogeneous components (IC's, passives etc.) over several vertical layers/modules. For these systems component placement today is a time consuming task. Even more important is the lack of a tool support for technology selection. This paper presents a new method for component autoplacement for folded and stacked 2.5D SiP integrated with technology selection on an objective basis. We propose a design approach that is based on the simultaneous consideration of numerous layout solutions. We discuss the structuring of physical design, present a novel modeling of technological components for folded and stacked 2.5D SiP, and sketch algorithms for technology constrained automated placement, based on multicriteria optimization. Together with a multicriteria decision support tool this results in a novel design approach for 2.5D SiP.
- 1 December 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 623-630
Technology Aware Modeling of 2.5D-SiP for Automation in Physical Design
The vertical integration within the system-in-package (SiP) approach is becoming more and more important. While system-on-ohip (SoC) and PCB design teams are operating with highly developed EDA tools, there is a lack of automation tools for the design of SiP. This is particularly true for the engineering of so called 2.5D SiP, which integrate heterogeneous components (IC's, passives etc.) over several vertical layers/modules. For these systems component placement today is a time consuming task. Even more important is the lack of a tool support for technology selection. This paper presents a new method for component autoplacement for folded and stacked 2.5D SiP integrated with technology selection on an objective basis. We propose a design approach that is based on the simultaneous consideration of numerous layout solutions. We discuss the structuring of physical design, present a novel modeling of technological components for folded and stacked 2.5D SiP, and sketch algorithms for technology constrained automated placement, based on multicriteria optimization. Together with a multicriteria decision support tool this results in a novel design approach for 2.5D SiP.
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 15505723,p. 11
System Integration Technologies for Ultra Small Systems
Abstract form only given. System integration technologies have increasingly become an important factor for the economic success of system suppliers and users especially in the areas of consumer electronics and telecommunications. Faced with the rapid development of IC technology the traditional packaging is changing into a complex system integration technique to satisfy the growing demand in terms of increased functionality, performance and miniaturization. The progress in system integration technologies in the last years allows the technical realization of new system concepts for highly miniaturized microsystems which are linked together in a wireless network. In future the integration of highly complex systems has to be carried out more cost efficiently, with a high degree of miniaturization and flexibility in adaptation to different applications. New integration technologies will be able to combine different approaches to integrate devices for sensing, electrical signal and data processing, wireless communication, power conversion and storage. With respect of complex functionalities (electrical, non-electrical, optical functions) these small systems can achieve a higher complexity compared to system on chip solutions at lower cost. The so called "e Grains" with a small size and an integrated sensor are able to receive, process, store and send data in an network environment. In order to reduce the physical space requirements of such wireless sensor nodes, new integration technologies are required which also use the third dimension for systems integration. In terms of design, hardware, technology and software, system integration based on the innovative "e-Grain" concept represents an entirely new challenge and requires a synergy of individual technologies at an exceptionally early stage
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 15505723,p. 11
System Integration Technologies for Ultra Small Systems
Abstract form only given. System integration technologies have increasingly become an important factor for the economic success of system suppliers and users especially in the areas of consumer electronics and telecommunications. Faced with the rapid development of IC technology the traditional packaging is changing into a complex system integration technique to satisfy the growing demand in terms of increased functionality, performance and miniaturization. The progress in system integration technologies in the last years allows the technical realization of new system concepts for highly miniaturized microsystems which are linked together in a wireless network. In future the integration of highly complex systems has to be carried out more cost efficiently, with a high degree of miniaturization and flexibility in adaptation to different applications. New integration technologies will be able to combine different approaches to integrate devices for sensing, electrical signal and data processing, wireless communication, power conversion and storage. With respect of complex functionalities (electrical, non-electrical, optical functions) these small systems can achieve a higher complexity compared to system on chip solutions at lower cost. The so called "e Grains" with a small size and an integrated sensor are able to receive, process, store and send data in an network environment. In order to reduce the physical space requirements of such wireless sensor nodes, new integration technologies are required which also use the third dimension for systems integration. In terms of design, hardware, technology and software, system integration based on the innovative "e-Grain" concept represents an entirely new challenge and requires a synergy of individual technologies at an exceptionally early stage
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 5 pp.
Packaging of radiation and particle detectors
Packaging of semiconductor detector modules has been one of the most promising research projects at Fraunhofer IZM. The applications vary from X-ray detection for medical diagnostics to particle detection for fundamental physical research. Starting from feasibility studies a high yield manufacturing process has been established. In this paper the bumping and assembly technology of pixel detector modules is exemplified by the manufacturing of modules for the setup of the ATLAS pixel detector at the large hadron collider (LHC) at CERN, Geneva. The pixel contacts and the interconnection bumps are deposited by electroplating. Yield is one of the most important parameters for the implementation of multichip module (MCM) concepts. Therefore a high yield manufacturing technology requires consistent electrical test and optical inspection on wafer level as well as on chip level running in parallel to the production process. A total module yield of 98% for packaging of 1000 MCMs each having 16 flip-chips has been achieved. Further examples of pixel detectors packaged at Fraunhofer IZM are presented in this paper. These are complex particle detector prototypes with diamond sensor material and pixel detector modules for X-ray imaging. The different amount of readout chips assembled on one sensor substrate and the amount of modules for the assembly of the whole detector require different manufacture technologies from single chip processing up to processing on wafer level
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 5 pp.
Packaging of radiation and particle detectors
Packaging of semiconductor detector modules has been one of the most promising research projects at Fraunhofer IZM. The applications vary from X-ray detection for medical diagnostics to particle detection for fundamental physical research. Starting from feasibility studies a high yield manufacturing process has been established. In this paper the bumping and assembly technology of pixel detector modules is exemplified by the manufacturing of modules for the setup of the ATLAS pixel detector at the large hadron collider (LHC) at CERN, Geneva. The pixel contacts and the interconnection bumps are deposited by electroplating. Yield is one of the most important parameters for the implementation of multichip module (MCM) concepts. Therefore a high yield manufacturing technology requires consistent electrical test and optical inspection on wafer level as well as on chip level running in parallel to the production process. A total module yield of 98% for packaging of 1000 MCMs each having 16 flip-chips has been achieved. Further examples of pixel detectors packaged at Fraunhofer IZM are presented in this paper. These are complex particle detector prototypes with diamond sensor material and pixel detector modules for X-ray imaging. The different amount of readout chips assembled on one sensor substrate and the amount of modules for the assembly of the whole detector require different manufacture technologies from single chip processing up to processing on wafer level
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 05695503,p. 8 pp.
Stackable thin film multi layer substrates with integrated passive components
Visionary concepts for future electronic systems, which are ubiquitous, extremely miniaturized and serve a wide range of services, are extremely challenging for current system integration and packaging technologies. In the meaning of hetero system integration different integration techniques, such as 3D integration, integration of passive components and assembly of thin chips, have to be combined to enable a further increase in package density. This paper describes an approach for 3D system integration using thin stackable substrates with high density interconnection layers, which include integrated inductors, capacitors and resistors. After a brief overview of the different passive test structures, which were exclusively designed for the evaluation of this approach, the process flow for the technological realization of the substrates were presented. Some results of the electrical characterization of the fabricated integrated passive structures were discussed. Finally initial results for the stacking of the substrates were presented
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 05695503,p. 8 pp.
Stackable thin film multi layer substrates with integrated passive components
Visionary concepts for future electronic systems, which are ubiquitous, extremely miniaturized and serve a wide range of services, are extremely challenging for current system integration and packaging technologies. In the meaning of hetero system integration different integration techniques, such as 3D integration, integration of passive components and assembly of thin chips, have to be combined to enable a further increase in package density. This paper describes an approach for 3D system integration using thin stackable substrates with high density interconnection layers, which include integrated inductors, capacitors and resistors. After a brief overview of the different passive test structures, which were exclusively designed for the evaluation of this approach, the process flow for the technological realization of the substrates were presented. Some results of the electrical characterization of the fabricated integrated passive structures were discussed. Finally initial results for the stacking of the substrates were presented
- 31 December 2005
- Published by Springer Nature
- p. 353-367
Miniaturized Wireless Sensors for Automotive Applications
- 31 December 2005
- Published by Springer Nature
- p. 353-367
Miniaturized Wireless Sensors for Automotive Applications
- 1 January 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1665-1670
Simulating Electromagnetic Interactions in High Power Density Inverters
In high power density inverters with integrated functions like filters and control electronics electromagnetic interaction between components becomes an important issue. Especially filters for electromagnetic interference are very sensitive to electromagnetic fields and therefore critical to design. Nevertheless only few guidelines for optimizing placement of filter components were published up to now. This paper introduces a simulation method for predicting stray fields of components and conducting structures, which is verified experimentally for different passive components and setups. The examples demonstrate a possibility of handling interaction problems
- 1 January 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1665-1670
Simulating Electromagnetic Interactions in High Power Density Inverters
In high power density inverters with integrated functions like filters and control electronics electromagnetic interaction between components becomes an important issue. Especially filters for electromagnetic interference are very sensitive to electromagnetic fields and therefore critical to design. Nevertheless only few guidelines for optimizing placement of filter components were published up to now. This paper introduces a simulation method for predicting stray fields of components and conducting structures, which is verified experimentally for different passive components and setups. The examples demonstrate a possibility of handling interaction problems
- 1 January 2004
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 1244-1250 Vol.2
Ultrathin soldered flip chip interconnections on flexible substrates
Flip chip assembly of silicon ICs on flexible substrates has gained more interest in the last years. On the one hand there are numerous low cost applications for this technology such as smart cards and smart labels, on the other hand flexible substrates offer a wide potential for highly complex folded packages and 3D modules. Using conventional flip chip assembly processes the stand-off is too high compared to the dimensions of chip and substrate. Until now solder application by stencil printing is only used successfully down to 150 /spl mu/m pitch with bump heights larger than 70 /spl mu/m due to the solder paste and stencil features. Deposition technologies for smaller solder volumes together with new assembly processes have to be developed and qualified to realize suitable contact heights. With the immersion soldering process a cost effective maskless bumping process for thin solder layers has been developed. Thermode bonding has been investigated as a promising fast flip chip technology for thin soldered contacts on flexible substrates. In this paper the process development for two different solder materials in combination with noflow underfiller materials will be presented for flip chip contacts of less than 10 /spl mu/m height. The reliability of thin solder joints is a key issue. Therefore, the failure mechanisms and the ageing behaviour were studied. The intermetallic phase formation has a larger influence because the intermetallics consume the majority of the solder alloy. The effect of intermetallic growth for the different solder materials as well as the impact of the small stand-off during ageing are investigated in this paper. Special emphasis is put on failures resulting from the joint geometry of ultrathin contacts. The promising results of a reliability test program consisting of thermal cycling, temperature/humidity testing and multiple reflow tests are discussed.
- 1 January 2004
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 1244-1250 Vol.2
Ultrathin soldered flip chip interconnections on flexible substrates
Flip chip assembly of silicon ICs on flexible substrates has gained more interest in the last years. On the one hand there are numerous low cost applications for this technology such as smart cards and smart labels, on the other hand flexible substrates offer a wide potential for highly complex folded packages and 3D modules. Using conventional flip chip assembly processes the stand-off is too high compared to the dimensions of chip and substrate. Until now solder application by stencil printing is only used successfully down to 150 /spl mu/m pitch with bump heights larger than 70 /spl mu/m due to the solder paste and stencil features. Deposition technologies for smaller solder volumes together with new assembly processes have to be developed and qualified to realize suitable contact heights. With the immersion soldering process a cost effective maskless bumping process for thin solder layers has been developed. Thermode bonding has been investigated as a promising fast flip chip technology for thin soldered contacts on flexible substrates. In this paper the process development for two different solder materials in combination with noflow underfiller materials will be presented for flip chip contacts of less than 10 /spl mu/m height. The reliability of thin solder joints is a key issue. Therefore, the failure mechanisms and the ageing behaviour were studied. The intermetallic phase formation has a larger influence because the intermetallics consume the majority of the solder alloy. The effect of intermetallic growth for the different solder materials as well as the impact of the small stand-off during ageing are investigated in this paper. Special emphasis is put on failures resulting from the joint geometry of ultrathin contacts. The promising results of a reliability test program consisting of thermal cycling, temperature/humidity testing and multiple reflow tests are discussed.
- 20 January 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 135-140
Reliability investigations of flip-chip solder bumps on palladium
The choice of the solder joint metallurgy is a key issue especially for the reliability of flip chip assemblies. Besides the systems which are already widely used and well understood, new materials are emerging as solderable under bump metallizations (UBMs). Palladium can be used as a basis for flip chip bumps in different ways: For single chip bumping Pd stud bumps form a solid core under the solder layer. These hard core solder bumps are an adequate solution if the dies are not available on wafer level and the chosen assembly technology is flip chip soldering. On wafer level electroless deposition of Palladium bumps is available on which solder can be deposited e.g. by stencil printing or meniscus bumping. The scope of this paper is to summarize the results from aging of eutectic Pb/Sn solder on Palladium stud bumps. The intermetallic growth which is observed and its impact on the mechanical and electrical reliability are investigated. Based on this data Palladium as an under bump metallization can be compared to alternative materials such as Nickel Author(s) Kallmayer, C. Tech. Univ. Berlin, Germany Oppermann, H. ; Anhock, S. ; Klein, M. ; Kalicki, R. ; Aschenbrenner, R. ; Reichl, H.
- 20 January 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 135-140
Reliability investigations of flip-chip solder bumps on palladium
The choice of the solder joint metallurgy is a key issue especially for the reliability of flip chip assemblies. Besides the systems which are already widely used and well understood, new materials are emerging as solderable under bump metallizations (UBMs). Palladium can be used as a basis for flip chip bumps in different ways: For single chip bumping Pd stud bumps form a solid core under the solder layer. These hard core solder bumps are an adequate solution if the dies are not available on wafer level and the chosen assembly technology is flip chip soldering. On wafer level electroless deposition of Palladium bumps is available on which solder can be deposited e.g. by stencil printing or meniscus bumping. The scope of this paper is to summarize the results from aging of eutectic Pb/Sn solder on Palladium stud bumps. The intermetallic growth which is observed and its impact on the mechanical and electrical reliability are investigated. Based on this data Palladium as an under bump metallization can be compared to alternative materials such as Nickel Author(s) Kallmayer, C. Tech. Univ. Berlin, Germany Oppermann, H. ; Anhock, S. ; Klein, M. ; Kalicki, R. ; Aschenbrenner, R. ; Reichl, H.
- 1 January 2002
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 144-149
Current loadability of ICA for flip chip applications
Miniaturization is a key issue to achieve advanced performance of electronic devices and to decrease the overall cost of an electronic package. In this respect the flip chip technology provides excellent capabilities to meet the demands of recent and future products. Although solder joining is still the most common technology a great deal of research work has been conducted on conductive adhesives. They are successfully used as die attach, display and hybrid assembly. Progress with its application to flip chip devices has still to be made. Recently, the current carrying capability of isotropic conductive adhesive (ICA) has been a matter of great interest. Predominantly, corresponding characteristics of anisotropic conductive adhesives (ACAs) have been studied by several groups. Though interest, mainly on part of the automotive industry is shown, little is known about ICA's high current behaviour. This paper is part of a broad study focused on the current capabilities of isotropic conductive adhesives. Tests have been carried out on flip chip assemblies. The contact resistivities depending on different DC loads and increased environmental temperatures have been monitored. In-situ measurements have been carried out with an automated measuring system. TGA measurements were made to find out about degradation temperatures of the used materials. The results contribute to the following discussion about the failure mechanisms due to high current loads.
- 1 January 2002
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 144-149
Current loadability of ICA for flip chip applications
Miniaturization is a key issue to achieve advanced performance of electronic devices and to decrease the overall cost of an electronic package. In this respect the flip chip technology provides excellent capabilities to meet the demands of recent and future products. Although solder joining is still the most common technology a great deal of research work has been conducted on conductive adhesives. They are successfully used as die attach, display and hybrid assembly. Progress with its application to flip chip devices has still to be made. Recently, the current carrying capability of isotropic conductive adhesive (ICA) has been a matter of great interest. Predominantly, corresponding characteristics of anisotropic conductive adhesives (ACAs) have been studied by several groups. Though interest, mainly on part of the automotive industry is shown, little is known about ICA's high current behaviour. This paper is part of a broad study focused on the current capabilities of isotropic conductive adhesives. Tests have been carried out on flip chip assemblies. The contact resistivities depending on different DC loads and increased environmental temperatures have been monitored. In-situ measurements have been carried out with an automated measuring system. TGA measurements were made to find out about degradation temperatures of the used materials. The results contribute to the following discussion about the failure mechanisms due to high current loads.