C. Kallmayer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
C. Kallmayer has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Herbert Reichl
Fraunhofer IZM, Gustav-Meyer-Allee 25, 13355 Berlin, Germany
3 shared publications R. Aschenbrenner
Res. Center of Microperipheric Technol., Technische Univ. Berlin, Germany
3 shared publicationsB. Pahl
Res. Center of Microperipheric Technol., Technische Univ. Berlin, Germany
2 shared publicationsH. Oppermann
1 shared publicationJ. Haberland
Res. Center Microperipheric Technol., Berlin Tech. Univ., Germany
1 shared publicationM. Klein
1 shared publication
Latest Publications
- 1 January 2004
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 1244-1250 Vol.2
Ultrathin soldered flip chip interconnections on flexible substrates
Flip chip assembly of silicon ICs on flexible substrates has gained more interest in the last years. On the one hand there are numerous low cost applications for this technology such as smart cards and smart labels, on the other hand flexible substrates offer a wide potential for highly complex folded packages and 3D modules. Using conventional flip chip assembly processes the stand-off is too high compared to the dimensions of chip and substrate. Until now solder application by stencil printing is only used successfully down to 150 /spl mu/m pitch with bump heights larger than 70 /spl mu/m due to the solder paste and stencil features. Deposition technologies for smaller solder volumes together with new assembly processes have to be developed and qualified to realize suitable contact heights. With the immersion soldering process a cost effective maskless bumping process for thin solder layers has been developed. Thermode bonding has been investigated as a promising fast flip chip technology for thin soldered contacts on flexible substrates. In this paper the process development for two different solder materials in combination with noflow underfiller materials will be presented for flip chip contacts of less than 10 /spl mu/m height. The reliability of thin solder joints is a key issue. Therefore, the failure mechanisms and the ageing behaviour were studied. The intermetallic phase formation has a larger influence because the intermetallics consume the majority of the solder alloy. The effect of intermetallic growth for the different solder materials as well as the impact of the small stand-off during ageing are investigated in this paper. Special emphasis is put on failures resulting from the joint geometry of ultrathin contacts. The promising results of a reliability test program consisting of thermal cycling, temperature/humidity testing and multiple reflow tests are discussed.
- 1 January 2004
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 1244-1250 Vol.2
Ultrathin soldered flip chip interconnections on flexible substrates
Flip chip assembly of silicon ICs on flexible substrates has gained more interest in the last years. On the one hand there are numerous low cost applications for this technology such as smart cards and smart labels, on the other hand flexible substrates offer a wide potential for highly complex folded packages and 3D modules. Using conventional flip chip assembly processes the stand-off is too high compared to the dimensions of chip and substrate. Until now solder application by stencil printing is only used successfully down to 150 /spl mu/m pitch with bump heights larger than 70 /spl mu/m due to the solder paste and stencil features. Deposition technologies for smaller solder volumes together with new assembly processes have to be developed and qualified to realize suitable contact heights. With the immersion soldering process a cost effective maskless bumping process for thin solder layers has been developed. Thermode bonding has been investigated as a promising fast flip chip technology for thin soldered contacts on flexible substrates. In this paper the process development for two different solder materials in combination with noflow underfiller materials will be presented for flip chip contacts of less than 10 /spl mu/m height. The reliability of thin solder joints is a key issue. Therefore, the failure mechanisms and the ageing behaviour were studied. The intermetallic phase formation has a larger influence because the intermetallics consume the majority of the solder alloy. The effect of intermetallic growth for the different solder materials as well as the impact of the small stand-off during ageing are investigated in this paper. Special emphasis is put on failures resulting from the joint geometry of ultrathin contacts. The promising results of a reliability test program consisting of thermal cycling, temperature/humidity testing and multiple reflow tests are discussed.
- 20 January 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 135-140
Reliability investigations of flip-chip solder bumps on palladium
The choice of the solder joint metallurgy is a key issue especially for the reliability of flip chip assemblies. Besides the systems which are already widely used and well understood, new materials are emerging as solderable under bump metallizations (UBMs). Palladium can be used as a basis for flip chip bumps in different ways: For single chip bumping Pd stud bumps form a solid core under the solder layer. These hard core solder bumps are an adequate solution if the dies are not available on wafer level and the chosen assembly technology is flip chip soldering. On wafer level electroless deposition of Palladium bumps is available on which solder can be deposited e.g. by stencil printing or meniscus bumping. The scope of this paper is to summarize the results from aging of eutectic Pb/Sn solder on Palladium stud bumps. The intermetallic growth which is observed and its impact on the mechanical and electrical reliability are investigated. Based on this data Palladium as an under bump metallization can be compared to alternative materials such as Nickel Author(s) Kallmayer, C. Tech. Univ. Berlin, Germany Oppermann, H. ; Anhock, S. ; Klein, M. ; Kalicki, R. ; Aschenbrenner, R. ; Reichl, H.
- 20 January 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 135-140
Reliability investigations of flip-chip solder bumps on palladium
The choice of the solder joint metallurgy is a key issue especially for the reliability of flip chip assemblies. Besides the systems which are already widely used and well understood, new materials are emerging as solderable under bump metallizations (UBMs). Palladium can be used as a basis for flip chip bumps in different ways: For single chip bumping Pd stud bumps form a solid core under the solder layer. These hard core solder bumps are an adequate solution if the dies are not available on wafer level and the chosen assembly technology is flip chip soldering. On wafer level electroless deposition of Palladium bumps is available on which solder can be deposited e.g. by stencil printing or meniscus bumping. The scope of this paper is to summarize the results from aging of eutectic Pb/Sn solder on Palladium stud bumps. The intermetallic growth which is observed and its impact on the mechanical and electrical reliability are investigated. Based on this data Palladium as an under bump metallization can be compared to alternative materials such as Nickel Author(s) Kallmayer, C. Tech. Univ. Berlin, Germany Oppermann, H. ; Anhock, S. ; Klein, M. ; Kalicki, R. ; Aschenbrenner, R. ; Reichl, H.
- 1 January 2002
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 144-149
Current loadability of ICA for flip chip applications
Miniaturization is a key issue to achieve advanced performance of electronic devices and to decrease the overall cost of an electronic package. In this respect the flip chip technology provides excellent capabilities to meet the demands of recent and future products. Although solder joining is still the most common technology a great deal of research work has been conducted on conductive adhesives. They are successfully used as die attach, display and hybrid assembly. Progress with its application to flip chip devices has still to be made. Recently, the current carrying capability of isotropic conductive adhesive (ICA) has been a matter of great interest. Predominantly, corresponding characteristics of anisotropic conductive adhesives (ACAs) have been studied by several groups. Though interest, mainly on part of the automotive industry is shown, little is known about ICA's high current behaviour. This paper is part of a broad study focused on the current capabilities of isotropic conductive adhesives. Tests have been carried out on flip chip assemblies. The contact resistivities depending on different DC loads and increased environmental temperatures have been monitored. In-situ measurements have been carried out with an automated measuring system. TGA measurements were made to find out about degradation temperatures of the used materials. The results contribute to the following discussion about the failure mechanisms due to high current loads.
- 1 January 2002
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 144-149
Current loadability of ICA for flip chip applications
Miniaturization is a key issue to achieve advanced performance of electronic devices and to decrease the overall cost of an electronic package. In this respect the flip chip technology provides excellent capabilities to meet the demands of recent and future products. Although solder joining is still the most common technology a great deal of research work has been conducted on conductive adhesives. They are successfully used as die attach, display and hybrid assembly. Progress with its application to flip chip devices has still to be made. Recently, the current carrying capability of isotropic conductive adhesive (ICA) has been a matter of great interest. Predominantly, corresponding characteristics of anisotropic conductive adhesives (ACAs) have been studied by several groups. Though interest, mainly on part of the automotive industry is shown, little is known about ICA's high current behaviour. This paper is part of a broad study focused on the current capabilities of isotropic conductive adhesives. Tests have been carried out on flip chip assemblies. The contact resistivities depending on different DC loads and increased environmental temperatures have been monitored. In-situ measurements have been carried out with an automated measuring system. TGA measurements were made to find out about degradation temperatures of the used materials. The results contribute to the following discussion about the failure mechanisms due to high current loads.