Dimitrios K. Atmatzidis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Dimitrios K. Atmatzidis has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Ioannis N. Markou
Soil Mechanics and Foundation Engineering Laboratory, Department of Civil Engineering, Democritus University of Thrace, University Campus Kimmeria, GR-67150 Xanthi, Greece
5 shared publications - Ioannis A. Pantazopoulos
Department of Civil Engineering, Geotechnical Engineering Laboratory, University of Patras, Patras, Greece
4 shared publications A. I. Droudakis
Dept. of Civil Engineering, University of Patras, Greece
1 shared publicationD. N. Christodoulou
Democritus University of Thrace
1 shared publication- D. N. Christodoulou
Assistant Professor, Democritus University of Thrace, Dept. of Civil Engineering, Soil Mechanics & Foundation Engineering Lab., 12 Vas. Sofias str., GR-67100 Xanthi, Greece
1 shared publication E. S. Petala
Democritus University of Thrace
1 shared publication
Latest Publications
- 5 February 2021
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 7 (1) , 1-17
Performance of Microfine Cement Grouted Sands Under Quick Loading Conditions
- 5 February 2021
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 7 (1) , 1-17
Performance of Microfine Cement Grouted Sands Under Quick Loading Conditions
- 3 November 2020
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 80 (2) , 1875-1890
Predicted and measured hydraulic conductivity of sand-sized crushed limestone
- 3 November 2020
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 80 (2) , 1875-1890
Predicted and measured hydraulic conductivity of sand-sized crushed limestone
- 25 September 2017
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 36 (2) , 1-23
Injectability of Microfine Cement Grouts into Limestone Sands with Different Gradations: Experimental Investigation and Prediction
- 25 September 2017
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 36 (2) , 1-23
Injectability of Microfine Cement Grouts into Limestone Sands with Different Gradations: Experimental Investigation and Prediction
- 17 August 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 2003-2012
Effect of Sand Gradation on the Groutability of Cement Suspensions
A laboratory investigation was conducted in order to evaluate the effect of sand grain size distribution on the groutability of ordinary and microfine cement suspensions. Four gradations from CEM II/B-M (according to EN 197-1) type of cement were used having nominal maximum grain sizes of 100 μm, 40 μm, 20 μm and 10 μm. Suspensions with water to cement ratios of 1, 2 and 3, by weight, were used. Groutability was evaluated by conducting one-dimensional injections into 45 clean sands with different gradations, using a specially constructed device. Groutability of cement suspensions increases with increasing cement fineness and/or water to cement ratio. Microfine cement suspensions with water to cement ratios of 2 and 3 can penetrate into medium to fine sands. Groutability predictions by groutability ratios are not always confirmed by laboratory injections. Synthesis of the finer portion of the sand gradation (D ≤ D25) affects substantially the result of the injection process and, therefore, is taken into consideration in this investigation by using a "modified uniformity coefficient" and a "modified groutability ratio".
- 17 August 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 2003-2012
Effect of Sand Gradation on the Groutability of Cement Suspensions
A laboratory investigation was conducted in order to evaluate the effect of sand grain size distribution on the groutability of ordinary and microfine cement suspensions. Four gradations from CEM II/B-M (according to EN 197-1) type of cement were used having nominal maximum grain sizes of 100 μm, 40 μm, 20 μm and 10 μm. Suspensions with water to cement ratios of 1, 2 and 3, by weight, were used. Groutability was evaluated by conducting one-dimensional injections into 45 clean sands with different gradations, using a specially constructed device. Groutability of cement suspensions increases with increasing cement fineness and/or water to cement ratio. Microfine cement suspensions with water to cement ratios of 2 and 3 can penetrate into medium to fine sands. Groutability predictions by groutability ratios are not always confirmed by laboratory injections. Synthesis of the finer portion of the sand gradation (D ≤ D25) affects substantially the result of the injection process and, therefore, is taken into consideration in this investigation by using a "modified uniformity coefficient" and a "modified groutability ratio".
- 17 August 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 1711-1720
Resonant Column Testing of Microfine Cement Grouted Sands
Torsional resonant column tests were conducted on microfine and ordinary cement grouted sands and shear modulus and damping ratio values were obtained. The effect of confining pressure, shear strain, cement type and gradation, grout water-to-cement (W/C) ratio and sand gradation were investigated. The shear modulus of the grouted sands increased with increasing confining pressure, decreasing shear strain and decreasing W/C ratio, while the damping ratio increased with decreasing confining pressure, increasing shear strain and increasing W/C ratio. The effect of other material parameters was minor or negligible.
- 17 August 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 1711-1720
Resonant Column Testing of Microfine Cement Grouted Sands
Torsional resonant column tests were conducted on microfine and ordinary cement grouted sands and shear modulus and damping ratio values were obtained. The effect of confining pressure, shear strain, cement type and gradation, grout water-to-cement (W/C) ratio and sand gradation were investigated. The shear modulus of the grouted sands increased with increasing confining pressure, decreasing shear strain and decreasing W/C ratio, while the damping ratio increased with decreasing confining pressure, increasing shear strain and increasing W/C ratio. The effect of other material parameters was minor or negligible.
- 17 August 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 1721-1730
Triaxial Compression Testing of Microfine Cement Grouted Sands
Unconsolidated-undrained (single and multi-stage) and consolidated-undrained triaxial compression tests with pore water pressure measurement were conducted to evaluate the deformability and shear strength parameters of microfine cement grouted sands. The effects of cement type and gradation, grout water-to-cement ratio (W/C), test type and distance from injection point were investigated. Grouting with microfine cement suspensions improves significantly the stress-strain-strength behavior of sands, the improvement primarily controlled by the W/C ratio of the suspensions, and is, generally, superior to grouting with ordinary cements. Grouting with a thick or a thin suspension (W/C=1 or 3), respectively, increases the initial tangent modulus of the sands by a factor of 13 and 3.5, reduces the strain at failure of the sand by a factor of 7.5 and 1.5 and provides the sand with cohesion of about 1500 kPa and 350 kPa.
- 17 August 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 1721-1730
Triaxial Compression Testing of Microfine Cement Grouted Sands
Unconsolidated-undrained (single and multi-stage) and consolidated-undrained triaxial compression tests with pore water pressure measurement were conducted to evaluate the deformability and shear strength parameters of microfine cement grouted sands. The effects of cement type and gradation, grout water-to-cement ratio (W/C), test type and distance from injection point were investigated. Grouting with microfine cement suspensions improves significantly the stress-strain-strength behavior of sands, the improvement primarily controlled by the W/C ratio of the suspensions, and is, generally, superior to grouting with ordinary cements. Grouting with a thick or a thin suspension (W/C=1 or 3), respectively, increases the initial tangent modulus of the sands by a factor of 13 and 3.5, reduces the strain at failure of the sand by a factor of 7.5 and 1.5 and provides the sand with cohesion of about 1500 kPa and 350 kPa.
- 1 April 1990
- Published by Elsevier in International Journal of Rock Mechanics and Mining Sciences
- Vol. 27 (2) , A114
Observed performance of a deep excavation in clay
- 1 April 1990
- Published by Elsevier in International Journal of Rock Mechanics and Mining Sciences
- Vol. 27 (2) , A114
Observed performance of a deep excavation in clay