Ioannis N. Markou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ioannis N. Markou has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Dimitrios K. Atmatzidis
Department of Civil Engineering, Geotechnical Engineering Laboratory, University of Patras, Patras, Greece
5 shared publications - Ioannis A. Pantazopoulos
Department of Civil Engineering, Geotechnical Engineering Laboratory, University of Patras, Patras, Greece
4 shared publications A. I. Droudakis
Soil Mechanics and Foundation Engineering Laboratory, Department of Civil Engineering, Democritus University of Thrace, Xanthi, Greece
3 shared publications- Evangelos D. Evangelou
Soil Mechanics and Foundation Engineering Laboratory, Department of Civil Engineering, Democritus University of Thrace, University Campus Kimmeria, GR-67150 Xanthi, Greece
3 shared publications - Konstantinos E. Bantralexis
Soil Mechanics and Foundation Engineering Laboratory, Department of Civil Engineering, Democritus University of Thrace, University Campus Kimmeria, GR-67150 Xanthi, Greece
3 shared publications D. K. Atmatzidis
Professor, Geotechnical Engineering Laboratory, Dept. of Civil Engineering, School of Engineering, Univ. of Patras, Rio, Patras GR-26500, Greece
2 shared publications
Latest Publications
- Open Access
Dynamic Parameters of Fiber-Reinforced Soils at Very Small Strains
Improvement of the engineering properties of soils by reinforcing them with fibers, at an appropriate percentage of the weight of dry soil, is frequently selected to ensure the safe construction and operation of many structures. However, the published information regarding the investigation of the dynamic properties of fiber-reinforced soils at very small strains is very limited. Toward this end, the dynamic behavior of fiber-reinforced soils is investigated experimentally by conducting Bender Element tests under different confining pressures. The effect of polypropylene fiber reinforcement on the shear wave velocity (Vs), the velocity of the primary wave (Vp), the initial Young’s modulus (E0) and the initial shear modulus (G0) of sand and sand–clay mixtures with varying compositions is examined in this study. The soils were reinforced with five different types of polypropylene fibers having lengths from 9 mm to 50 mm, at fiber contents from 0.5% to 2% by weight of dry soil. The results indicate that the dynamic and the small-strain stiffness parameters of fiber-reinforced soils increase with increasing confining pressure, while also being affected by the soil type, the fiber type, and content. Although fiber inclusion resulted generally in a reduction of the dynamic properties of soils, increases ranging from 5% to 55% were observed in certain soil–fiber combinations in comparison with the unreinforced soils.
Open AccessDynamic Parameters of Fiber-Reinforced Soils at Very Small Strains
Improvement of the engineering properties of soils by reinforcing them with fibers, at an appropriate percentage of the weight of dry soil, is frequently selected to ensure the safe construction and operation of many structures. However, the published information regarding the investigation of the dynamic properties of fiber-reinforced soils at very small strains is very limited. Toward this end, the dynamic behavior of fiber-reinforced soils is investigated experimentally by conducting Bender Element tests under different confining pressures. The effect of polypropylene fiber reinforcement on the shear wave velocity (Vs), the velocity of the primary wave (Vp), the initial Young’s modulus (E0) and the initial shear modulus (G0) of sand and sand–clay mixtures with varying compositions is examined in this study. The soils were reinforced with five different types of polypropylene fibers having lengths from 9 mm to 50 mm, at fiber contents from 0.5% to 2% by weight of dry soil. The results indicate that the dynamic and the small-strain stiffness parameters of fiber-reinforced soils increase with increasing confining pressure, while also being affected by the soil type, the fiber type, and content. Although fiber inclusion resulted generally in a reduction of the dynamic properties of soils, increases ranging from 5% to 55% were observed in certain soil–fiber combinations in comparison with the unreinforced soils.
- Open Access
- 1 September 2025
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 644, 02006
Development of shear resistance at cohesive soil – geotextile interfaces
The shear resistance at cohesive soil – geotextile interfaces is important for the proper design of geotextile-lined structures. Although the interaction behaviour at cohesive soil – geotextile interfaces has been studied in the past, most of those research efforts have been focused primarily on the determination of the shear resistance at failure. Therefore, an attempt to quantify the development of shear resistance at the cohesive soil – geotextile interfaces with increasing shearing displacement is presented in this study. Toward this end, direct shear tests were conducted on soil – geotextile interfaces using a modified 100 mm shear box. A compacted cohesive soil of low plasticity (CL) was tested in contact with three woven and four non-woven geotextiles of five types. The direct shear tests yielded polynomial failure envelopes for the cohesive soil – geotextile interfaces, possibly indicating a transition from drained to undrained conditions at the interface with increasing normal stress. A special method for the determination of the interface shear strength parameters considering the non-linearity of the failure envelopes, is applied in the present study. The shear resistance parameters are functions of the shearing displacement at the cohesive soil – geotextile interfaces and their values at failure reveal a transition from “friction-like” behaviour to “adhesion-like” behaviour as normal stress increases.
- 1 September 2025
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 644, 02006
Open AccessDevelopment of shear resistance at cohesive soil – geotextile interfaces
The shear resistance at cohesive soil – geotextile interfaces is important for the proper design of geotextile-lined structures. Although the interaction behaviour at cohesive soil – geotextile interfaces has been studied in the past, most of those research efforts have been focused primarily on the determination of the shear resistance at failure. Therefore, an attempt to quantify the development of shear resistance at the cohesive soil – geotextile interfaces with increasing shearing displacement is presented in this study. Toward this end, direct shear tests were conducted on soil – geotextile interfaces using a modified 100 mm shear box. A compacted cohesive soil of low plasticity (CL) was tested in contact with three woven and four non-woven geotextiles of five types. The direct shear tests yielded polynomial failure envelopes for the cohesive soil – geotextile interfaces, possibly indicating a transition from drained to undrained conditions at the interface with increasing normal stress. A special method for the determination of the interface shear strength parameters considering the non-linearity of the failure envelopes, is applied in the present study. The shear resistance parameters are functions of the shearing displacement at the cohesive soil – geotextile interfaces and their values at failure reveal a transition from “friction-like” behaviour to “adhesion-like” behaviour as normal stress increases.
- 24 November 2023
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 9 (6) , 1-3
Guest Editorial for the Special Issue on “Soil–Geosynthetic Interaction”
- 24 November 2023
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 9 (6) , 1-3
Guest Editorial for the Special Issue on “Soil–Geosynthetic Interaction”
- Open Access
- 5 September 2023
- Published by MDPI AG in Geotechnics
- Vol. 3 (3) , 874-893
Mechanical Behavior of Fiber-Reinforced Soils under Undrained Triaxial Loading Conditions
The design of fiber-reinforced soil structures, such as embankments and pavements, can be carried out using the results of unconsolidated, undrained triaxial compression tests conducted on specimens at their “as-compacted” water content and analyzed in terms of total stresses. The effects of soil and fiber type on the mechanical behavior of fiber-reinforced soils have not been methodically or adequately examined in the past under these conditions, and the effects of fiber length and content on the shear strength parameters of fiber-reinforced soils need further experimental documentation. Accordingly, five soils ranging from “excellent” to “poor” materials for use in earthwork structures were tested in the present study, in combination with five types of polypropylene fibers having lengths ranging from 9 to 50 mm. Unconsolidated undrained triaxial compression tests were conducted on specimens at their “as-compacted” water content, with fiber contents ranging from 0.5 to 2% by weight of dry soil. Fiber reinforcement reduces the stiffness and increases the deformability of the soil. The fiber-reinforced soils exhibit a more ductile behavior in comparison with the unreinforced soils. A Mohr–Coulomb type linear failure criterion satisfactorily describes the shear strength behavior of fiber-reinforced soils in total stress terms. The cohesion values of the fiber-reinforced soils range between 61 kPa and 301 kPa and increase up to seven times in comparison with the cohesion values of the unreinforced soils. The variations of the angle of internal friction of soils due to fiber reinforcement are generally limited to ±25%. The cohesion improvement due to fiber reinforcement is increased with increasing fiber content and fiber length up to 30 mm and is inversely proportional to the fine-grained fraction and the cohesion of the unreinforced soil.
- 5 September 2023
- Published by MDPI AG in Geotechnics
- Vol. 3 (3) , 874-893
Open AccessMechanical Behavior of Fiber-Reinforced Soils under Undrained Triaxial Loading Conditions
The design of fiber-reinforced soil structures, such as embankments and pavements, can be carried out using the results of unconsolidated, undrained triaxial compression tests conducted on specimens at their “as-compacted” water content and analyzed in terms of total stresses. The effects of soil and fiber type on the mechanical behavior of fiber-reinforced soils have not been methodically or adequately examined in the past under these conditions, and the effects of fiber length and content on the shear strength parameters of fiber-reinforced soils need further experimental documentation. Accordingly, five soils ranging from “excellent” to “poor” materials for use in earthwork structures were tested in the present study, in combination with five types of polypropylene fibers having lengths ranging from 9 to 50 mm. Unconsolidated undrained triaxial compression tests were conducted on specimens at their “as-compacted” water content, with fiber contents ranging from 0.5 to 2% by weight of dry soil. Fiber reinforcement reduces the stiffness and increases the deformability of the soil. The fiber-reinforced soils exhibit a more ductile behavior in comparison with the unreinforced soils. A Mohr–Coulomb type linear failure criterion satisfactorily describes the shear strength behavior of fiber-reinforced soils in total stress terms. The cohesion values of the fiber-reinforced soils range between 61 kPa and 301 kPa and increase up to seven times in comparison with the cohesion values of the unreinforced soils. The variations of the angle of internal friction of soils due to fiber reinforcement are generally limited to ±25%. The cohesion improvement due to fiber reinforcement is increased with increasing fiber content and fiber length up to 30 mm and is inversely proportional to the fine-grained fraction and the cohesion of the unreinforced soil.
- Open Access
- 2 March 2023
- Published by Elsevier in Developments in the Built Environment
- Vol. 14
Use of sand pore-size distribution to predict cement suspension groutability
- 2 March 2023
- Published by Elsevier in Developments in the Built Environment
- Vol. 14
Open AccessUse of sand pore-size distribution to predict cement suspension groutability
- 1 October 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 34 (10) , 04022273
Stress–Strain–Strength and Hydraulic Performance of Microfine Cement Grouted Sands
An experimental investigation was conducted in order to evaluate the effectiveness of six new microfine cement grouts obtained by pulverizing three ordinary cements with different chemical composition. Both consolidated-undrained with pore pressure measurement (CU-PP) triaxial compression and hydraulic conductivity tests were conducted on each grouted sand specimen. Grouting increased the stiffness and reduces the hydraulic conductivity of the sands. The shear-strength behavior of the grouted sands was described satisfactorily by the Mohr-Coulomb failure criterion. The bleed capacity of the injected suspensions was a good indicator of the grouting-induced mechanical and hydraulic behavior improvement. Grouting with stable [water to cement ratio ] microfine cement suspensions was superior to grouting with coarser cements at , yielded hydraulic conductivity values as low as , added cohesion reaching 2 MPa and, on the average, increased the initial modulus of elasticity by 10 times, reduced failure deformation by 5 times, and increased the peak strength by 8.5 times. Grouting with unstable microfine cement suspensions provided measurable, but not as pronounced, improvement. A change in stress–strain–strength behavior of grouted sands, associated with the beginning of cementitious bonds breakage, was systematically observed at low axial deformation (0.2%–0.7%).- 1 October 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 34 (10) , 04022273
Stress–Strain–Strength and Hydraulic Performance of Microfine Cement Grouted Sands
An experimental investigation was conducted in order to evaluate the effectiveness of six new microfine cement grouts obtained by pulverizing three ordinary cements with different chemical composition. Both consolidated-undrained with pore pressure measurement (CU-PP) triaxial compression and hydraulic conductivity tests were conducted on each grouted sand specimen. Grouting increased the stiffness and reduces the hydraulic conductivity of the sands. The shear-strength behavior of the grouted sands was described satisfactorily by the Mohr-Coulomb failure criterion. The bleed capacity of the injected suspensions was a good indicator of the grouting-induced mechanical and hydraulic behavior improvement. Grouting with stable [water to cement ratio ] microfine cement suspensions was superior to grouting with coarser cements at , yielded hydraulic conductivity values as low as , added cohesion reaching 2 MPa and, on the average, increased the initial modulus of elasticity by 10 times, reduced failure deformation by 5 times, and increased the peak strength by 8.5 times. Grouting with unstable microfine cement suspensions provided measurable, but not as pronounced, improvement. A change in stress–strain–strength behavior of grouted sands, associated with the beginning of cementitious bonds breakage, was systematically observed at low axial deformation (0.2%–0.7%).- 9 June 2022
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 8 (3) , 1-11
Compaction Characteristics of Fiber-Reinforced Soils
- 9 June 2022
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 8 (3) , 1-11
Compaction Characteristics of Fiber-Reinforced Soils
- 5 February 2021
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 7 (1) , 1-17
Performance of Microfine Cement Grouted Sands Under Quick Loading Conditions
- 5 February 2021
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 7 (1) , 1-17
Performance of Microfine Cement Grouted Sands Under Quick Loading Conditions
- 3 November 2020
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 80 (2) , 1875-1890
Predicted and measured hydraulic conductivity of sand-sized crushed limestone
- 3 November 2020
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 80 (2) , 1875-1890
Predicted and measured hydraulic conductivity of sand-sized crushed limestone
- Open Access
- 1 August 2020
- Published by Elsevier in Soils and Foundations
- Vol. 60 (4) , 825-839
Prediction of cement suspension groutability based on sand hydraulic conductivity
- 1 August 2020
- Published by Elsevier in Soils and Foundations
- Vol. 60 (4) , 825-839
Open AccessPrediction of cement suspension groutability based on sand hydraulic conductivity