THTiansheng Hong

Tiansheng Hong

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Tiansheng Hong has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Calibration and Analysis of Mechanical Modeling for Traction Wire Rope of Mountainous Orchard Carrier

    by Yuping Ouyang, Tianyu Wang, Tiansheng Hong, Xudong Sun

    Low-cost transporting vehicles are a crucial routine for orchards in the mountainous place. As the core component of the mountainous orchard carrier, the wire rope is easily damaged due to frequent handling of agricultural materials. The mechanical model of carrier wire rope is the prerequisite for studying its damage mechanism. This paper first analyzes the load-bearing characteristics of the wire rope of the carrier and then uses the theory of differential geometry and the elasticity of the wire rope to establish the mechanical model of the wire rope side strand strain ε0 and the axial load T of the wire rope end face in the erect state and the radial contact pressure Fa of the wire rope at the bending section and the mechanical model of the axial tension F and the pulley diameter D of the wire rope end face. On the basis of the mechanical model and the wire rope geometric solid model, the finite element stress analysis of the wire rope in the vertical state was carried out to verify the accuracy of the wire rope stress model. The results show that when the wire rope was in the vertical state, the wire-wire contact stress was linear directly proportional to the load on the end face of the wire rope; the wire-wire contact stress between the strands was about 12 times that within the strand; the average error between the simulated value and calculated value was about 13.6, proving the correctness of the established wire mechanics model. When the rope and wheel were in contact, the contact pressure of the outer wire of the side strand was only related to the axial tension of the wire rope end face and the diameter of the pulley but not to the elasticity modulus of the pulley.


  • Open Access

    Influence of Toothed Rail Parameters on Impact Vibration Meshing of Mountainous Self-Propelled Electric Monorail Transporter

    by Yue Liu, Tiansheng Hong, Zhen Li

    In order to reduce the vibration of mountain self-propelled electric monorail transporters (MSEMT) caused by the impact of the meshing of roller gear with toothed rail (MRGTR), and to improve the stability and safety of monorail transporters, this paper theoretically analyzed the MRGTR mechanism of toothed monorail transporters as well as established the MSEMT displacement model and its instantaneous velocity model. The vibration signals of MSEMT with four different parameters of toothed rail were collected by the acceleration sensor and signal acquisition system. The signals were analyzed by the Hilbert envelope demodulation method to investigate the influence of toothed rail parameters on meshing impact vibration. Moreover, taking the vibration acceleration amplitude of MSEMT and the vibration attenuation time of meshing impact as evaluation indexes, a test based on the three-factor and two-level orthogonal test was engaged with factors of toothed rail pressure angle, the ratio of L—the chord length of two adjacent roller centers of a roller gear—and rack pitch p (wheel-tooth ratio) and the load mass of the MSEMT. It showed that the impact of MRGTR was the main excitation source of the vibration of MSEMT. The pressure angle and wheel-tooth ratio both have a significant impact on the smooth operation of MSEMT, the latter to a greater extent. So did the interaction between wheel-tooth ratio and load mass. The amplitude of the characteristic frequency of the MSEMT decreased with the growth of the pressure angle. When the wheel-tooth ratio was cosα, the number of the characteristic frequency was less than that when it was 1, and the amplitude became smaller too. When the pressure angle was 15, the amplitude of vibration acceleration characteristic frequency decreased as a consequence of load mass increasing. At the pressure angle of 25, the amplitude of characteristic frequency decreased with the increase of load mass if the wheel-tooth ratio was 1, and the opposite result occurs in the case when the wheel-tooth ratio was cosα. This paper provides a theoretical basis and reference for improving the impact vibration of MRGTR and optimizing the design of the toothed rail.


  • An Expert System for Tractor Fault Diagnosis Based on Ontology and Web

    by Chunyin Wu, Qing Ouyang, Shouhua Yu, Chengjian Deng, Xiaojuan Mao, Tiansheng Hong

  • Plan and Design of Intelligent Citrus Orchard Irrigation System

    by Xuejun Yue, Tiansheng Hong, Jianian Li, Tongbiao Sun

  • An Illumination Intensity Collecting System of Citrus Leaf Based on WSN

    by Xuejun Yue, Tiansheng Hong, Songbin Zhai, Yuanjie Chen

  • Data transmission performance for 2.4GHz in-field wireless sensor network

    by Zhen Li, Tiansheng Hong, Ning Wang, Tao Wen

    Wireless sensor network (WSN) technology is a promising solution for large-scale, real-time, and continuous soil property data acquisition. However, the applications are still very limited due to a lack of understanding of the WSN in-field data transmission performance. In this study, commercial 2.4GHz wireless sensor modules were used to set up a test platform to evaluate data transmission performance. Indexed packets transmitted from a module were received by another equal module to calculate packet delivery rate (PDR). Experiments were conducted in a wheat field of an experimental farm of Oklahoma State University. Canopy height, transmitter height, receiver height and transmitter-to-receiver distance (T-R distance) were considered as impact factors on data transmission. Correlation analysis was used to evaluate the relationship between path-loss and PDR. The results indicated that, with the increase of the plant height, path-loss and PDR became more correlated with each other. A distance of 70m was defined as a stable communication distance for the 2.4GHz in-field WSN applications.


  • Study of Fruiter LAI Realtime Measurement System

    by Tiansheng Hong, Weibin Wu, Zhen Li, Lei Xiao, Wenzhao Zhang

    Leaf area index (LAI) is a critical structural parameter in evaluating physiology and biology of vegetation canopy and ecosystem, which makes its quick and precise measurement necessary though still unrealized owing to the different LAI definitions, diverse suggestions and measurement variance. And virtual plant, virtual reality and virtual instruments (VI) provide new tools in agricultural measurement based on increasing development of computer technology. By integrating virtual plants, virtual reality and virtual instrument technologies, a fruiter LAI realtime measurement system was established to test LAI of real Litchi and LAI of manmade Litchi made with 3D digitalizer base on the real one. One the one hand, LAI system compiles OpenGL and VC++ with LabVIEW for computer model simulating, and on the other hand, system analyzes, saves and displays data such as PAR, temperatures, and sensor position, then calculates the LAI and output motor control order to realize the sensor movement. Hereinto, a kind of useful random distribution arithmetic was created and distributed leaves were visualized and shadowed. Additionally, LAI arithmetic for Litchi was test for optimal sampling parameters. After calibration and comparison, the LAI system is satisfied to our project requirement.