Bernadette Schlüter
Research Subjects
Research Interests
Bernadette Schlüter has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Andreas Brenner
Fraunhofer Institute for Laser Technology, 52074 Aachen, Germany
2 shared publications - Bernhard Blug
Fraunhofer Institute for Mechanics of Materials, 79108 Freiburg, Germany
2 shared publications - Christof Koplin
Fraunhofer IWM MikroTribologie Centrum, Wöhlerstr. 9, 79108 Freiburg, Germany
2 shared publications - Franziska Kirsch
Fraunhofer Institute for Structural Durability and System Reliability LBF, 64289 Darmstadt, Germany
2 shared publications - Raimund Jaeger
Fraunhofer IWM MikroTribologie Centrum, Wöhlerstr. 9, 79108 Freiburg, Germany
2 shared publications - Sönke Vogel
RWTH Aachen University
2 shared publications
Latest Publications
- Open Access
- 13 March 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (3) , 135
Running-In Effects of Lubricated Polyether Ether Ketone on Steel for Different Spreading and Sorption Tendencies
Polyether ether ketone is a highly resilient thermoplastic that can withstand as an unfilled or filled polymer tribological high loads in high-temperature applications, as it has a high glass and melting temperature. Currently, it attracts interest as a lubricated material for drive systems to minimize noise, as a lightweight solution improving the CO2 balance, or in combination with novel lubricants. We have produced friction and wear maps with pin-on-disk tests on steel axial bearing rings and investigated the interaction and running-in behavior with different lubricants, such as different polyalkylene glycols, polyalphaolefin, and various esters. In general, the behavior of polyether ether ketone is hardly influenced by the frictional heat when loaded at room temperature. It shows a lubricant-specific polymer transfer and surface softening. This running-in impact is enhanced if a loading strategy with initial high friction power is applied. The beneficial transfer forms on the track in mixed lubrication on the rough counterpart until an increasing adhesive contact limits this effect. The appearance of a minimal wear coefficient was found below the glass temperature with lubricants strongly sorbing in polyether ether ketones, such as polar polyalkylenglycol or trimellitic acid ester-based lubricants. Using the interfacial energy of the system to derive an energy term describing the tendency to form a stable transfer, systematic trends in the tribological behavior of polyether ether ketone and polyketone could be identified that can be projected on other systems.
- 13 March 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (3) , 135
Open AccessRunning-In Effects of Lubricated Polyether Ether Ketone on Steel for Different Spreading and Sorption Tendencies
Polyether ether ketone is a highly resilient thermoplastic that can withstand as an unfilled or filled polymer tribological high loads in high-temperature applications, as it has a high glass and melting temperature. Currently, it attracts interest as a lubricated material for drive systems to minimize noise, as a lightweight solution improving the CO2 balance, or in combination with novel lubricants. We have produced friction and wear maps with pin-on-disk tests on steel axial bearing rings and investigated the interaction and running-in behavior with different lubricants, such as different polyalkylene glycols, polyalphaolefin, and various esters. In general, the behavior of polyether ether ketone is hardly influenced by the frictional heat when loaded at room temperature. It shows a lubricant-specific polymer transfer and surface softening. This running-in impact is enhanced if a loading strategy with initial high friction power is applied. The beneficial transfer forms on the track in mixed lubrication on the rough counterpart until an increasing adhesive contact limits this effect. The appearance of a minimal wear coefficient was found below the glass temperature with lubricants strongly sorbing in polyether ether ketones, such as polar polyalkylenglycol or trimellitic acid ester-based lubricants. Using the interfacial energy of the system to derive an energy term describing the tendency to form a stable transfer, systematic trends in the tribological behavior of polyether ether ketone and polyketone could be identified that can be projected on other systems.
- Open Access
Influence of Graphene Type and Content on Friction and Wear of Silicon Carbide/Graphene Nanocomposites in Aqueous Environment
Two different types of graphene materials were used as functional nanofillers for the mechanical and tribological improvement of silicon carbide/graphene nanocomposites. On the one hand is thermally reduced graphite oxide (TRGO) reduced at three different temperatures, and on the other hand is graphene made of three different organic precursors, which were directly coated on silicon carbide (SiC) platelets (GSiC). Additionally, benchmark materials were also used as carbon fillers. The SiC/graphene nanocomposites with 2 wt% filler content were manufactured by pressureless sintering (PLS). Some composites were produced with higher graphene contents of 4% and 8% and sintered by spark plasma sintering (SPS). Microstructural analyses were conducted using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Underwater lubrication, the SP sintered TRGO and GSiC materials with high graphene content have shown the most promising tribological performance. Furthermore, the reduced size of the homogeneously distributed nanoparticles promotes the formation of surface states, which improve the friction and wear properties.
Open AccessInfluence of Graphene Type and Content on Friction and Wear of Silicon Carbide/Graphene Nanocomposites in Aqueous Environment
Two different types of graphene materials were used as functional nanofillers for the mechanical and tribological improvement of silicon carbide/graphene nanocomposites. On the one hand is thermally reduced graphite oxide (TRGO) reduced at three different temperatures, and on the other hand is graphene made of three different organic precursors, which were directly coated on silicon carbide (SiC) platelets (GSiC). Additionally, benchmark materials were also used as carbon fillers. The SiC/graphene nanocomposites with 2 wt% filler content were manufactured by pressureless sintering (PLS). Some composites were produced with higher graphene contents of 4% and 8% and sintered by spark plasma sintering (SPS). Microstructural analyses were conducted using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Underwater lubrication, the SP sintered TRGO and GSiC materials with high graphene content have shown the most promising tribological performance. Furthermore, the reduced size of the homogeneously distributed nanoparticles promotes the formation of surface states, which improve the friction and wear properties.
- Open Access
- 12 May 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (5) , 93
Wear and the Transition from Static to Mixed Lubricated Friction of Sorption or Spreading Dominated Metal-Thermoplastic Contacts
Stiction, run-in wear and friction of lubricated polyoxymethylene homopolymer (POM)- and aliphatic polyamide (PA46)-steel tribosystems were investigated for mild-loaded mixed lubrication conditions with and without thermal conditioning of the polymers in the lubricant prior to testing. Macroscopic oscillatory tribometry and standard gliding experiments were carried out. The hypothesis that sorption of a lubricant into a thermoplastic polymer and partial solving of the surface by the lubricant can change wear rate and friction was tested. It was found that for POM-lubricant-pairings, the tribological behavior is dominated by the sorption of the lubricant into the polymer; it is not influenced by the spreading energy. For the PA46-lubricant pairings, no mass uptake by sorption was measured, and the tribological behavior is influenced by spreading and changes in hardness due to thermal aging. For mild loading in mixed lubricated conditions, friction and wear properties seem to be primarily determined by the hardness-dependence of abrasive contact and less by adhesion or hysteretic mechanisms.
- 12 May 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (5) , 93
Open AccessWear and the Transition from Static to Mixed Lubricated Friction of Sorption or Spreading Dominated Metal-Thermoplastic Contacts
Stiction, run-in wear and friction of lubricated polyoxymethylene homopolymer (POM)- and aliphatic polyamide (PA46)-steel tribosystems were investigated for mild-loaded mixed lubrication conditions with and without thermal conditioning of the polymers in the lubricant prior to testing. Macroscopic oscillatory tribometry and standard gliding experiments were carried out. The hypothesis that sorption of a lubricant into a thermoplastic polymer and partial solving of the surface by the lubricant can change wear rate and friction was tested. It was found that for POM-lubricant-pairings, the tribological behavior is dominated by the sorption of the lubricant into the polymer; it is not influenced by the spreading energy. For the PA46-lubricant pairings, no mass uptake by sorption was measured, and the tribological behavior is influenced by spreading and changes in hardness due to thermal aging. For mild loading in mixed lubricated conditions, friction and wear properties seem to be primarily determined by the hardness-dependence of abrasive contact and less by adhesion or hysteretic mechanisms.
- Open Access
Laser Structuring and DLC Coating of Elastomers for High Performance Applications
Even though hard, low friction coatings such as diamond like carbon (DLC) would be beneficial for the performance and longevity of rubber seals, a crucial challenge remains. The elastic mismatch of rubber substrate and DLC coating prevents a fracture free coating application. In this work, a nature inspired approach is applied to render the stiff coating flexible and resilient to delamination at the same time by direct patterning. Rubber substrates were laser structured with tile patterns and subsequently DLC coated. Tensile and tribology tests were performed on structured and unstructured samples. Unstructured DLC coatings showed a crack pattern induced by the coating process, which was further fragmented by tensile stress. Coatings with tile patterns did not experience a further fragmentation under load. During continuous tribological loading, less heterogenous damage is produced for tile structured samples. The findings are ascribed to the relief of induced coating stress by the tile structure, meaning a more resilient coating.
Open AccessLaser Structuring and DLC Coating of Elastomers for High Performance Applications
Even though hard, low friction coatings such as diamond like carbon (DLC) would be beneficial for the performance and longevity of rubber seals, a crucial challenge remains. The elastic mismatch of rubber substrate and DLC coating prevents a fracture free coating application. In this work, a nature inspired approach is applied to render the stiff coating flexible and resilient to delamination at the same time by direct patterning. Rubber substrates were laser structured with tile patterns and subsequently DLC coated. Tensile and tribology tests were performed on structured and unstructured samples. Unstructured DLC coatings showed a crack pattern induced by the coating process, which was further fragmented by tensile stress. Coatings with tile patterns did not experience a further fragmentation under load. During continuous tribological loading, less heterogenous damage is produced for tile structured samples. The findings are ascribed to the relief of induced coating stress by the tile structure, meaning a more resilient coating.
- Open Access
- 23 March 2022
- Published by MDPI AG in Preprints.org
Laser Structuring and DLC Coating of Elastomers for High Performance Applications
Even though hard, low friction coatings such as diamond like carbon (DLC) would be beneficial for the per-formance and longevity of rubber seals, a crucial challenge – as graphically illustrated in Figure 1.a – remains. The elastic mismatch of rubber substrate and DLC coating prevents a fracture free coating application. In this work a nature inspired approach (Figure 1.b) is applied to render the stiff coating flexible and resilient to delamination at the same time by direct patterning. Rubber substrates were laser structured with tile patterns and subsequently DLC-coated. Tensile and tribology tests were performed on structured and unstructured samples. Unstructured DLC-coatings showed a crack pattern induced by the coating process, which was further fragmented by tensile stress. Coatings with tile patterns did not experience a further fragmentation under load. During continuous tribological loading, less heterogenous damage is produced for tile structured samples. The findings are ascribed to the relief of induced coating stress by the tile structure, meaning a more resilient coating.
- 23 March 2022
- Published by MDPI AG in Preprints.org
Open AccessLaser Structuring and DLC Coating of Elastomers for High Performance Applications
Even though hard, low friction coatings such as diamond like carbon (DLC) would be beneficial for the per-formance and longevity of rubber seals, a crucial challenge – as graphically illustrated in Figure 1.a – remains. The elastic mismatch of rubber substrate and DLC coating prevents a fracture free coating application. In this work a nature inspired approach (Figure 1.b) is applied to render the stiff coating flexible and resilient to delamination at the same time by direct patterning. Rubber substrates were laser structured with tile patterns and subsequently DLC-coated. Tensile and tribology tests were performed on structured and unstructured samples. Unstructured DLC-coatings showed a crack pattern induced by the coating process, which was further fragmented by tensile stress. Coatings with tile patterns did not experience a further fragmentation under load. During continuous tribological loading, less heterogenous damage is produced for tile structured samples. The findings are ascribed to the relief of induced coating stress by the tile structure, meaning a more resilient coating.
- 1 December 2013
- Published by Springer Nature in Tribology Letters
- Vol. 53 (1) , 353-363
Synthesis and Tribological Characterization of Stable Dispersions of Thermally Reduced Graphite Oxide
- 1 December 2013
- Published by Springer Nature in Tribology Letters
- Vol. 53 (1) , 353-363
Synthesis and Tribological Characterization of Stable Dispersions of Thermally Reduced Graphite Oxide