Hossein Gholizadeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hossein Gholizadeh has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Douglas Bitner
Department of Mechanical Engineering, University of Saskatchewan, Saskatoon, SK S7N 5A9, Canada
1 shared publication Greg Schoenau
Department of Mechanical Engineering, University of Saskatchewan 57 Campus Drive, Saskatoon, Saskatchewan, Canada, S7N 5A9 Contact
1 shared publication- Greg Schoenau
Department of Mechanical Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK S7N 5A9, Canada
1 shared publication Richard Burton
Department of Mechanical Engineering, University of Saskatchewan 57 Campus Drive, Saskatoon, Saskatchewan, Canada, S7N 5A9 Contact
1 shared publication- Richard Burton
University of Saskatchewan, Saskatoon, SK, Canada
1 shared publication
Latest Publications
- 12 June 2014
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 136 (5) , 051013
Modeling and Experimental Validation of the Effective Bulk Modulus of a Mixture of Hydraulic Oil and Air
It is well known that the presence of entrained air bubbles in hydraulic oil can significantly reduce the effective bulk modulus of hydraulic oil. The effective bulk modulus of a mixture of oil and air as pressure changes is considerably different than when the oil and air are not mixed. Theoretical models have been proposed in the literature to simulate the pressure sensitivity of the effective bulk modulus of this mixture. However, limited amounts of experimental data are available to prove the validity of the models under various operating conditions. The major factors that affect pressure sensitivity of the effective bulk modulus of the mixture are the amount of air bubbles, their size and the distribution, and rate of compression of the mixture. An experimental apparatus was designed to investigate the effect of these variables on the effective bulk modulus of the mixture. The experimental results were compared with existing theoretical models, and it was found that the theoretical models only matched the experimental data under specific conditions. The purpose of this paper is to specify the conditions in which the current theoretical models can be used to represent the real behavior of the pressure sensitivity of the effective bulk modulus of the mixture. Additionally, a new theoretical model is proposed for situations where the current models fail to truly represent the experimental data.
- 12 June 2014
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 136 (5) , 051013
Modeling and Experimental Validation of the Effective Bulk Modulus of a Mixture of Hydraulic Oil and Air
It is well known that the presence of entrained air bubbles in hydraulic oil can significantly reduce the effective bulk modulus of hydraulic oil. The effective bulk modulus of a mixture of oil and air as pressure changes is considerably different than when the oil and air are not mixed. Theoretical models have been proposed in the literature to simulate the pressure sensitivity of the effective bulk modulus of this mixture. However, limited amounts of experimental data are available to prove the validity of the models under various operating conditions. The major factors that affect pressure sensitivity of the effective bulk modulus of the mixture are the amount of air bubbles, their size and the distribution, and rate of compression of the mixture. An experimental apparatus was designed to investigate the effect of these variables on the effective bulk modulus of the mixture. The experimental results were compared with existing theoretical models, and it was found that the theoretical models only matched the experimental data under specific conditions. The purpose of this paper is to specify the conditions in which the current theoretical models can be used to represent the real behavior of the pressure sensitivity of the effective bulk modulus of the mixture. Additionally, a new theoretical model is proposed for situations where the current models fail to truly represent the experimental data.
- 1 January 2012
- Published by River Publishers in International Journal of Fluid Power
- Vol. 13 (1) , 7-16
Fluid Bulk Modulus: Comparison of Low Pressure Models
Fluid bulk modulus is a fluid property that has been studied extensively over the past. The numerical value of this property depends on the operating conditions, the amount of entrained air/gas, and the way compression is applied and to some extent, the mathematical form it is defined. In a companion paper, an extensive review of fluid bulk modulus was presented. From this review, it was established that many models for fluid bulk modulus in the low pressure range (below critical pressure) have been forwarded. However, many of these models are based on assumptions that have not been explicitly defined. This paper considers these models and attempts to quantify the underlying assumptions. In addition some modification to these models are proposed in order to compare their prediction in the case where air/gas in entrained, for example. The paper concludes by categorizing the models into two groups and recommending the best model that can be used for each group. Finally some problems which observed in the models are discussed and future work for solving these problems presented.
- 1 January 2012
- Published by River Publishers in International Journal of Fluid Power
- Vol. 13 (1) , 7-16
Fluid Bulk Modulus: Comparison of Low Pressure Models
Fluid bulk modulus is a fluid property that has been studied extensively over the past. The numerical value of this property depends on the operating conditions, the amount of entrained air/gas, and the way compression is applied and to some extent, the mathematical form it is defined. In a companion paper, an extensive review of fluid bulk modulus was presented. From this review, it was established that many models for fluid bulk modulus in the low pressure range (below critical pressure) have been forwarded. However, many of these models are based on assumptions that have not been explicitly defined. This paper considers these models and attempts to quantify the underlying assumptions. In addition some modification to these models are proposed in order to compare their prediction in the case where air/gas in entrained, for example. The paper concludes by categorizing the models into two groups and recommending the best model that can be used for each group. Finally some problems which observed in the models are discussed and future work for solving these problems presented.