Richard Burton
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Richard Burton has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Greg Schoenau
Department of Mechanical Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK S7N 5A9, Canada
3 shared publications - Saeid Habibi
Department of Mechanical Engineering, McMaster University, Hamilton, ON L8S 4L8, Canada
2 shared publications Yang Lin
University of Saskatchewan, Saskatoon, SK, Canada
2 shared publicationsYang Shi
University of Saskatchewan, Saskatoon, SK, Canada
2 shared publications- Douglas Bitner
Department of Mechanical Engineering, University of Saskatchewan, Saskatoon, SK S7N 5A9, Canada
1 shared publication - Hossein Gholizadeh
Department of Mechanical Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK S7N 5A9, Canada
1 shared publication
Latest Publications
- 12 June 2014
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 136 (5) , 051013
Modeling and Experimental Validation of the Effective Bulk Modulus of a Mixture of Hydraulic Oil and Air
It is well known that the presence of entrained air bubbles in hydraulic oil can significantly reduce the effective bulk modulus of hydraulic oil. The effective bulk modulus of a mixture of oil and air as pressure changes is considerably different than when the oil and air are not mixed. Theoretical models have been proposed in the literature to simulate the pressure sensitivity of the effective bulk modulus of this mixture. However, limited amounts of experimental data are available to prove the validity of the models under various operating conditions. The major factors that affect pressure sensitivity of the effective bulk modulus of the mixture are the amount of air bubbles, their size and the distribution, and rate of compression of the mixture. An experimental apparatus was designed to investigate the effect of these variables on the effective bulk modulus of the mixture. The experimental results were compared with existing theoretical models, and it was found that the theoretical models only matched the experimental data under specific conditions. The purpose of this paper is to specify the conditions in which the current theoretical models can be used to represent the real behavior of the pressure sensitivity of the effective bulk modulus of the mixture. Additionally, a new theoretical model is proposed for situations where the current models fail to truly represent the experimental data.
- 12 June 2014
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 136 (5) , 051013
Modeling and Experimental Validation of the Effective Bulk Modulus of a Mixture of Hydraulic Oil and Air
It is well known that the presence of entrained air bubbles in hydraulic oil can significantly reduce the effective bulk modulus of hydraulic oil. The effective bulk modulus of a mixture of oil and air as pressure changes is considerably different than when the oil and air are not mixed. Theoretical models have been proposed in the literature to simulate the pressure sensitivity of the effective bulk modulus of this mixture. However, limited amounts of experimental data are available to prove the validity of the models under various operating conditions. The major factors that affect pressure sensitivity of the effective bulk modulus of the mixture are the amount of air bubbles, their size and the distribution, and rate of compression of the mixture. An experimental apparatus was designed to investigate the effect of these variables on the effective bulk modulus of the mixture. The experimental results were compared with existing theoretical models, and it was found that the theoretical models only matched the experimental data under specific conditions. The purpose of this paper is to specify the conditions in which the current theoretical models can be used to represent the real behavior of the pressure sensitivity of the effective bulk modulus of the mixture. Additionally, a new theoretical model is proposed for situations where the current models fail to truly represent the experimental data.
- 6 July 2012
- Published by Springer Nature
- p. 223-239
Modeling and H ∞ PID Plus Feedforward Controller Design for an Electrohydraulic Actuator System
- 6 July 2012
- Published by Springer Nature
- p. 223-239
Modeling and H ∞ PID Plus Feedforward Controller Design for an Electrohydraulic Actuator System
- 28 February 2011
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 133 (2) , 024504
Sliding Mode Controller and Filter Applied to an Electrohydraulic Actuator System
A common problem pertaining to linear or nonlinear systems is the design of a combined robust control and estimation strategy that can effectively deal with noise and uncertainties. The variable structure control (VSC) and its special form of sliding mode control (SMC) demonstrate robustness with regard to uncertainties, although their performance can be severely degraded by noise. As such they can benefit from using state estimates obtained from filters. In this regard, this paper considers the use of a recently proposed robust state and parameter estimation strategy referred to as the variable structure filter (VSF) in conjunction with SMC. The contribution of this paper is a new strategy that combines sliding mode control with the variable structure filter. In the presence of bounded parametric uncertainties and noise, this combined method demonstrates robust stability both in terms of control and state estimation. Furthermore, the combined strategy can be used to achieve high regulation rates or short settling time. The combined VSF and SMC strategy is demonstrated by its application to a high precision hydrostatic system, referred to as the electrohydraulic actuator system.
- 28 February 2011
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 133 (2) , 024504
Sliding Mode Controller and Filter Applied to an Electrohydraulic Actuator System
A common problem pertaining to linear or nonlinear systems is the design of a combined robust control and estimation strategy that can effectively deal with noise and uncertainties. The variable structure control (VSC) and its special form of sliding mode control (SMC) demonstrate robustness with regard to uncertainties, although their performance can be severely degraded by noise. As such they can benefit from using state estimates obtained from filters. In this regard, this paper considers the use of a recently proposed robust state and parameter estimation strategy referred to as the variable structure filter (VSF) in conjunction with SMC. The contribution of this paper is a new strategy that combines sliding mode control with the variable structure filter. In the presence of bounded parametric uncertainties and noise, this combined method demonstrates robust stability both in terms of control and state estimation. Furthermore, the combined strategy can be used to achieve high regulation rates or short settling time. The combined VSF and SMC strategy is demonstrated by its application to a high precision hydrostatic system, referred to as the electrohydraulic actuator system.
- 1 January 2009
- Published by ASME International
- p. 675-682
Modeling and Robust Discrete-Time Sliding Mode Control Design for a Fluid Power Electrohydraulic Actuator (EHA) System
This paper studies the design of a robust discrete-time sliding mode control (DT-SMC) for a high precision electro-hydraulic actuator (EHA) system with nonlinear actuator friction. Nonlinear friction in the hydraulic actuator can greatly influence the performance and accuracy of the hydraulic actuators; however, it is difficult to accurately model nonlinear friction characteristics. In this paper, it is proposed to characterize frictions as an uncertainty in the system matrices. Indeed, the effects of variations of the nonlinear friction coefficients are considered as norm bounded uncertainties that span a bounded region to cover a wide range of real actuator friction. For such a discrete-time dynamic model for the EHA system with system matrices uncertainties and a nonlinear term, a sufficient condition for the existence of stable sliding surfaces is proposed by using the linear matrix inequality (LMI) approach. Based on this existence condition, a discrete-time sliding mode controller is developed such that the reaching motion satisfies the discrete-time sliding mode reaching condition for uncertain systems. Simulation and comparison studies on the EHA system model illustrate the effectiveness of the proposed method. The study is simulation based only as it is important to establish the feasibility and stability of the controller before attempting to apply the controller to a physical system.
- 1 January 2009
- Published by ASME International
- p. 675-682
Modeling and Robust Discrete-Time Sliding Mode Control Design for a Fluid Power Electrohydraulic Actuator (EHA) System
This paper studies the design of a robust discrete-time sliding mode control (DT-SMC) for a high precision electro-hydraulic actuator (EHA) system with nonlinear actuator friction. Nonlinear friction in the hydraulic actuator can greatly influence the performance and accuracy of the hydraulic actuators; however, it is difficult to accurately model nonlinear friction characteristics. In this paper, it is proposed to characterize frictions as an uncertainty in the system matrices. Indeed, the effects of variations of the nonlinear friction coefficients are considered as norm bounded uncertainties that span a bounded region to cover a wide range of real actuator friction. For such a discrete-time dynamic model for the EHA system with system matrices uncertainties and a nonlinear term, a sufficient condition for the existence of stable sliding surfaces is proposed by using the linear matrix inequality (LMI) approach. Based on this existence condition, a discrete-time sliding mode controller is developed such that the reaching motion satisfies the discrete-time sliding mode reaching condition for uncertain systems. Simulation and comparison studies on the EHA system model illustrate the effectiveness of the proposed method. The study is simulation based only as it is important to establish the feasibility and stability of the controller before attempting to apply the controller to a physical system.
- 1 January 2007
- Published by ASME International
- p. 23-32
Discrete-Time H2-Optimal Control for Hydraulic Position Control Systems
Hydraulic position control systems play an important role in industrial automation. This paper explores the application of discrete-time H2-optimal control for a hydraulic position control system (HPCS). By minimizing the H2-norm of the system, the discrete-time robust H2-optimal control both stabilizes the plant and minimizes the root-mean-square of the servo position error simultaneously. The intuitive nature of this advanced approach helps to manage the selection of design parameters, whereas, classical methods provide less insight into strategies for parameter selection and control design. Additionally, the powerful ability to address disturbances and uncertainty in the robust H2-optimal design offers a more direct alternative to the ad hoc and iterative nature of classical methods for the hydraulic servo position system. Computer simulations illustrate the design procedure and the effectiveness of the proposed method. Experimental studies which employ the H2-optimal control on a hydraulic positioning system are also conducted and the results show that the method is suitable for practical applications.
- 1 January 2007
- Published by ASME International
- p. 23-32
Discrete-Time H2-Optimal Control for Hydraulic Position Control Systems
Hydraulic position control systems play an important role in industrial automation. This paper explores the application of discrete-time H2-optimal control for a hydraulic position control system (HPCS). By minimizing the H2-norm of the system, the discrete-time robust H2-optimal control both stabilizes the plant and minimizes the root-mean-square of the servo position error simultaneously. The intuitive nature of this advanced approach helps to manage the selection of design parameters, whereas, classical methods provide less insight into strategies for parameter selection and control design. Additionally, the powerful ability to address disturbances and uncertainty in the robust H2-optimal design offers a more direct alternative to the ad hoc and iterative nature of classical methods for the hydraulic servo position system. Computer simulations illustrate the design procedure and the effectiveness of the proposed method. Experimental studies which employ the H2-optimal control on a hydraulic positioning system are also conducted and the results show that the method is suitable for practical applications.
- 1 January 2007
- Published by ASME International
- p. 175-183
Investigation of a High Precision Hydrostatic Actuation System: How Nonlinearities Affect Its Performance
A prototype Electro-Hydraulic Actuator (EHA) system has demonstrated a positional accuracy in the order of 100 nanometer. Linearized models of the EHA have been formulated and have shown reasonable correlation to the performance of the physical EHA. However, these models predict zero steady state error (an impossible situation given the physical limitations of seals, friction etc.). Further, the prototype EHA indicates that the cut-off frequency decreases as the amplitude of the input signal decreases. This is not predicted by the linear models. In this paper the Bond-graph large scale modeling technique was used as the basis to formulate the describing equations of the EHA. The model was made increasingly more complex by introducing observable nonlinearities into the model. It was found that the introduction of nonlinear friction did show results whose trends were consistent with those observed experimentally. Assumed nonlinearities in the bulk modulus could not be substantiated. In addition, some of the observed experimental trends could not be predicted (such as order change) and pose additional challenges to be solved before a complete understanding of the true physics of the EHA can be realized.
- 1 January 2007
- Published by ASME International
- p. 175-183
Investigation of a High Precision Hydrostatic Actuation System: How Nonlinearities Affect Its Performance
A prototype Electro-Hydraulic Actuator (EHA) system has demonstrated a positional accuracy in the order of 100 nanometer. Linearized models of the EHA have been formulated and have shown reasonable correlation to the performance of the physical EHA. However, these models predict zero steady state error (an impossible situation given the physical limitations of seals, friction etc.). Further, the prototype EHA indicates that the cut-off frequency decreases as the amplitude of the input signal decreases. This is not predicted by the linear models. In this paper the Bond-graph large scale modeling technique was used as the basis to formulate the describing equations of the EHA. The model was made increasingly more complex by introducing observable nonlinearities into the model. It was found that the introduction of nonlinear friction did show results whose trends were consistent with those observed experimentally. Assumed nonlinearities in the bulk modulus could not be substantiated. In addition, some of the observed experimental trends could not be predicted (such as order change) and pose additional challenges to be solved before a complete understanding of the true physics of the EHA can be realized.
- 1 January 2007
- Published by ASME International
- p. 621-625
An Artificial Neural Network Approach to Payload Estimation in Four Wheel Drive Loaders
Estimation of the manipulated payload mass in off-highway machines is made non-trivial by the nonlinearities associated with the hydraulic systems used to actuate the linkage of the machine in addition to the nonlinearity of the kinematics of the linkage itself. Hydraulic cylinder friction, hydraulic conduit compressibility, linkage machining variation and linkage joint friction all make this a complex task under even ideal (machine static) conditions. This problem is made even more difficult when the linkage is mobile as is often the case with off-highway equipment such as four-wheel-drive loaders, cranes, and excavators. The rigid body motion of this type of equipment affects the gravitational loads seen in the linkage and impacts the payload estimate. The commercially available state-of-the-art load estimation solutions rely on the mobile machine becoming pseudo-static in order to maintain accuracy. This requirement increases the time required to move the material and decreases the productivity of the machine. An artificial neural network solution to this problem that enables the machine to remain dynamic and still accurately estimate the payload is discussed in this paper. Development and implementation on an actual four-wheel-drive loader is shown.
- 1 January 2007
- Published by ASME International
- p. 621-625
An Artificial Neural Network Approach to Payload Estimation in Four Wheel Drive Loaders
Estimation of the manipulated payload mass in off-highway machines is made non-trivial by the nonlinearities associated with the hydraulic systems used to actuate the linkage of the machine in addition to the nonlinearity of the kinematics of the linkage itself. Hydraulic cylinder friction, hydraulic conduit compressibility, linkage machining variation and linkage joint friction all make this a complex task under even ideal (machine static) conditions. This problem is made even more difficult when the linkage is mobile as is often the case with off-highway equipment such as four-wheel-drive loaders, cranes, and excavators. The rigid body motion of this type of equipment affects the gravitational loads seen in the linkage and impacts the payload estimate. The commercially available state-of-the-art load estimation solutions rely on the mobile machine becoming pseudo-static in order to maintain accuracy. This requirement increases the time required to move the material and decreases the productivity of the machine. An artificial neural network solution to this problem that enables the machine to remain dynamic and still accurately estimate the payload is discussed in this paper. Development and implementation on an actual four-wheel-drive loader is shown.
- 1 January 2002
- Published by The Japan Fluid Power Systems Society in Proceedings of the JFPS International Symposium on Fluid Power
- Vol. 2002 (5-1) , 265-270
Estimation of Friction and Spring Characteristics of a Variable Displacement Pump using the Extended Kalman Filter Approach
- 1 January 2002
- Published by The Japan Fluid Power Systems Society in Proceedings of the JFPS International Symposium on Fluid Power
- Vol. 2002 (5-1) , 265-270
Estimation of Friction and Spring Characteristics of a Variable Displacement Pump using the Extended Kalman Filter Approach