Stephan Guttowski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Stephan Guttowski has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- David Dimitry Polityko
Technical University Berlin, FSP Mikroperipherik (TUB-MP), Gustav-Meyer-Allee 25, D-13355, Berlin, Germany
2 shared publications Gerhard Fotheringham
Fraunhofer Institute for Reliability and Microintegration, 13355 Berlin, Germany
2 shared publications- Herbert Reichl
Fraunhofer IZM, Gustav-Meyer-Allee 25, 13355 Berlin, Germany
2 shared publications Michael Niedermayer
2 shared publicationsA. Ege Engin
Department of Electrical and Computer Engineering, San Diego State University, San Diego, USA
1 shared publicationCarsten Brockmann
1 shared publication
Latest Publications
- 21 February 2013
- Published by Walter de Gruyter GmbH in TM - Technisches Messen
- Vol. 80 (2) , 45-52
Drahtlose Sensorsysteme für die zustandsorientierte Instandhaltung und Logistik
Zusammenfassung Die Überwachung des Maschinenzustands ist die zwingende Voraussetzung für eine zustandsorientierte Instandhaltung. Hierzu sollen energieautarke Sensorsysteme nach dem Motto “Mount and forget” völlig wartungsfrei arbeiten und müssen zudem hohen Lebensdaueranforderungen gerecht werden. Batteriebasierte Lösungen scheiden dabei in der Regel aus. Sie werden ersetzt durch Systeme zur Versorgung mit Umgebungsenergie. Dieser Beitrag stellt Projekte und realisierte energieautarke Sensorsysteme vor aus den Bereichen zustandsbasierte Instandhaltung und Logistik, bespricht deren mögliche Energiequellen sowie Ultra-Low-Power Systemlösungen.
- 21 February 2013
- Published by Walter de Gruyter GmbH in TM - Technisches Messen
- Vol. 80 (2) , 45-52
Drahtlose Sensorsysteme für die zustandsorientierte Instandhaltung und Logistik
Zusammenfassung Die Überwachung des Maschinenzustands ist die zwingende Voraussetzung für eine zustandsorientierte Instandhaltung. Hierzu sollen energieautarke Sensorsysteme nach dem Motto “Mount and forget” völlig wartungsfrei arbeiten und müssen zudem hohen Lebensdaueranforderungen gerecht werden. Batteriebasierte Lösungen scheiden dabei in der Regel aus. Sie werden ersetzt durch Systeme zur Versorgung mit Umgebungsenergie. Dieser Beitrag stellt Projekte und realisierte energieautarke Sensorsysteme vor aus den Bereichen zustandsbasierte Instandhaltung und Logistik, bespricht deren mögliche Energiequellen sowie Ultra-Low-Power Systemlösungen.
- 13 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 53 (4) , 1005-1014
Integration of Planar Antennas Considering Electromagnetic Interactions at Board Level
In compact wireless modules, electromagnetic (EM) interactions occurring between planar antennas and transmission lines (TML) sharing the same substrate may cause a high amount of undesired coupling and may also detune the antenna characteristics. In this paper, an approach for defining a block-out region around the planar antenna, where no components should be placed is developed, thereby ensuring that the antenna characteristics remain within tolerable limits when the antenna is integrated at board level. This region is comparable to the reactive near-field, but is determined by evaluating the reactive EM power density excited on the ground plane and deducing a threshold value. Its boundary will be termed the EM antenna boundary. Furthermore, a method for efficient estimation of EM coupling from the antenna to terminated TMLs routed outside the EM antenna boundary is developed. This method is based entirely on a postprocessing step to field simulations, i.e., the coupling is calculated based on the previously computed magnetic field distribution excited by the antenna on the ground plane. The coupling model uses the theory of field excited TMLs together with the Baum-Liu-Tesche integral equations for obtaining the terminal voltages of the TML and, hence, the coupling terms.
- 13 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 53 (4) , 1005-1014
Integration of Planar Antennas Considering Electromagnetic Interactions at Board Level
In compact wireless modules, electromagnetic (EM) interactions occurring between planar antennas and transmission lines (TML) sharing the same substrate may cause a high amount of undesired coupling and may also detune the antenna characteristics. In this paper, an approach for defining a block-out region around the planar antenna, where no components should be placed is developed, thereby ensuring that the antenna characteristics remain within tolerable limits when the antenna is integrated at board level. This region is comparable to the reactive near-field, but is determined by evaluating the reactive EM power density excited on the ground plane and deducing a threshold value. Its boundary will be termed the EM antenna boundary. Furthermore, a method for efficient estimation of EM coupling from the antenna to terminated TMLs routed outside the EM antenna boundary is developed. This method is based entirely on a postprocessing step to field simulations, i.e., the coupling is calculated based on the previously computed magnetic field distribution excited by the antenna on the ground plane. The coupling model uses the theory of field excited TMLs together with the Baum-Liu-Tesche integral equations for obtaining the terminal voltages of the TML and, hence, the coupling terms.
- 1 December 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 623-630
Technology Aware Modeling of 2.5D-SiP for Automation in Physical Design
The vertical integration within the system-in-package (SiP) approach is becoming more and more important. While system-on-ohip (SoC) and PCB design teams are operating with highly developed EDA tools, there is a lack of automation tools for the design of SiP. This is particularly true for the engineering of so called 2.5D SiP, which integrate heterogeneous components (IC's, passives etc.) over several vertical layers/modules. For these systems component placement today is a time consuming task. Even more important is the lack of a tool support for technology selection. This paper presents a new method for component autoplacement for folded and stacked 2.5D SiP integrated with technology selection on an objective basis. We propose a design approach that is based on the simultaneous consideration of numerous layout solutions. We discuss the structuring of physical design, present a novel modeling of technological components for folded and stacked 2.5D SiP, and sketch algorithms for technology constrained automated placement, based on multicriteria optimization. Together with a multicriteria decision support tool this results in a novel design approach for 2.5D SiP.
- 1 December 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 623-630
Technology Aware Modeling of 2.5D-SiP for Automation in Physical Design
The vertical integration within the system-in-package (SiP) approach is becoming more and more important. While system-on-ohip (SoC) and PCB design teams are operating with highly developed EDA tools, there is a lack of automation tools for the design of SiP. This is particularly true for the engineering of so called 2.5D SiP, which integrate heterogeneous components (IC's, passives etc.) over several vertical layers/modules. For these systems component placement today is a time consuming task. Even more important is the lack of a tool support for technology selection. This paper presents a new method for component autoplacement for folded and stacked 2.5D SiP integrated with technology selection on an objective basis. We propose a design approach that is based on the simultaneous consideration of numerous layout solutions. We discuss the structuring of physical design, present a novel modeling of technological components for folded and stacked 2.5D SiP, and sketch algorithms for technology constrained automated placement, based on multicriteria optimization. Together with a multicriteria decision support tool this results in a novel design approach for 2.5D SiP.
- 31 December 2005
- Published by Springer Nature
- p. 353-367
Miniaturized Wireless Sensors for Automotive Applications
- 31 December 2005
- Published by Springer Nature
- p. 353-367
Miniaturized Wireless Sensors for Automotive Applications
- 1 January 2004
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 58 (3-4) , 54-57
Design Aspects of Self-Sufficient Distributed MicroSystems
- 1 January 2004
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 58 (3-4) , 54-57
Design Aspects of Self-Sufficient Distributed MicroSystems