KGKostandin Gjika

Kostandin Gjika

*This is an algorithmically generated author record based on publicly available information.

Kostandin Gjika has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • On the Influence of Lubricant Supply Conditions and Bearing Configuration to the Performance of (Semi) Floating Ring Bearing Systems for Turbochargers

    by Luis San Andrés, Feng Yu, Kostandin Gjika

    Engine oil-lubricated (semi) floating ring bearing ((S)FRB) systems in passenger vehicle turbochargers (TC) operate at temperatures well above ambient and must withstand large temperature gradients that can lead to severe thermomechanical induced stresses. Physical modeling of the thermal energy flow paths and an effective thermal management strategy are paramount to determine safe operating conditions ensuring the TC component mechanical integrity and the robustness of its bearing system. The paper details a model to predict the pressure and temperature fields and the distribution of thermal energy flows in a bearing system. The impact of lubricant supply conditions, bearing film clearances, and oil supply grooves is quantified. Either a low oil temperature or a high supply pressure increases the generated shear power. Either a high supply pressure or a large clearance allows more flow through the inner film and draws more heat from the hot journal, thought it increases the shear drag power as the oil viscosity remains high. Nonetheless, the peak temperature of the inner film is not influenced by the changes on the way the oil is supplied into the film as the thermal energy displaced from the hot shaft into the film is overwhelming. Adding axial grooves on the inner side of the (S)FRB improves its dynamic stability, albeit increasing the drawn oil flow as well as the drag power and heat from the shaft. The results identify a compromise between different parameters of groove designs thus enabling a bearing system with a low power consumption.


  • Turbocharger Synchronous Vibration Control on High Speed Balancer: Test and Prediction

    by Kostandin Gjika, Pradeep Mahadevan, Antoine Costeux

    Current trends for advanced automotive engines focusing on downsizing, better fuel efficiency, and lower emissions have led to several changes in turbocharger bearing systems design, and technology. Automotive turbochargers are running faster under high engine vibration level. Vibration control is becoming a real critical issue and turbocharger manufacturers are focusing more and more on new and improved balancing technology. This paper deals with turbocharger synchronous vibration control on high speed balancers. In a first step the synchronous rotordynamics behavior is identified. The developed fluid bearing code predicts bearing rotational speed (in case of fully floating design), operating inner and outer bearing film clearances and bearing force coefficients. A rotordynamics code uses this input to predict the synchronous lateral dynamic response of the rotor-bearing system by converging with bearing eccentricity ratio. The rotor-bearing system model is validated by shaft motion test data on high speed balancer (HSB). It shows that only one of the peaks seen on the synchronous G level plot collected in a high speed balancer can be explained by rotordynamics physics. A step-by-step structural dynamics model and analysis validated by experimental frequency response functions provides robust explanations for the other G level peaks. The synchronous vibration response of the system “turbocharger-HSB fixture” is predicted by integrating the predicted rotordynamics rotational bearing loads on the structural dynamics model. Numerous test data show very good correlation with the prediction, which validates the developed analytical model. The “rotordynamics—structural dynamics model” allows deep understanding of turbocharger synchronous vibration control, as well as optimization of the high speed balancer tooling.


  • Nonlinear Dynamic Behavior of Turbocharger Rotor-Bearing Systems With Hydrodynamic Oil Film and Squeeze Film Damper in Series: Prediction and Experiment

    by K. Gjika, L. San Andrés, G. D. Larue

    Current trends for advanced automotive engines focusing on downsizing, better fuel efficiency, and lower emissions have led to several changes in turbocharger bearing system design and technology. Automotive turbochargers run faster and use engine oils with very low viscosity under high oil inlet temperature and low feed pressure. The development of high performing bearing systems, marrying innovation with reliability, is a persistent challenge. This paper shows progress on the nonlinear dynamic behavior modeling of the rotor-radial bearing system (RBS) incorporating two oil films in series: a hydrodynamic one with a squeeze film damper commonly used in turbochargers. The developed fluid bearing code predicts bearing rotational speed (in the case of fully floating design), operating inner and outer bearing film clearances, effective oil viscosity, taking into account its shear effect, and hydrostatic load. A rotordynamics code uses this input to predict the nonlinear lateral dynamic response of the rotor-bearing system. The model predictions are validated with test data acquired on a high speed turbocharger RBS of a 6.0 mm journal diameter running up to 250,000 rpm (maximum speed), 5W30 oil type, 150°C oil inlet temperature, and 4 bar oil feed pressure. The tests are conducted at a rotordynamics technology laboratory using a high performance data acquisition system. Turbochargers with four combinations of inner and outer RBS clearances are tested. Prediction and measured synchronous response and total motion are in good agreement. Both demonstrate the nonlinear character of the RBS behavior, including several subsynchronous frequency components across the operating speed range. The nonlinear predictive model aids the development of high performance and optimized turbocharger RBS with faster development cycle times and increased reliability.


  • Turbocharger Nonlinear Response With Engine-Induced Excitations: Predictions and Test Data

    by Luis San Andre´s, Ash Maruyama, Kostandin Gjika, Sherry Xia

    Turbochargers (TCs) aid to produce smaller and more fuel-efficient passenger vehicle engines with power outputs comparable to those of large displacement engines. This paper presents further progress on the nonlinear dynamic behavior modeling of rotor-radial bearing system (RBS) by including engine-induced (TC casing) excitations. The application concerns to a semi-floating bearing design commonly used in high speed turbochargers. Predictions from the model are validated against test data collected in an engine-mounted TC unit operating to a top speed of 160 krpm (engine speed = 3600 rpm). The bearing model includes non-cylindrical lubricant films as in a semi-floating ring bearing with an anti-rotation button. The nonlinear rotor transient response model presently includes input base motions for the measured TC casing accelerations for increasing engine load conditions. Engines induce TC casing accelerations rich in multiple harmonic frequencies; amplitudes being significant at 2 and 4 times the main engine speed. FFT post-processing of predicted nonlinear TC shaft motions reveals a subsynchronous whirl frequency content in good agreement with test data, in particular for operation at the highest engine speeds. Predicted total shaft motion is also in good agreement with test data for all engine loads and over the operating TC shaft speed range. The comparisons validate the rotor-bearing model and will aid in reducing product development time and expenditures.


  • Nonlinear Dynamic Behavior of Turbocharger Rotor-Bearing Systems With Hydrodynamic Oil Film and Squeeze Film Damper in Series: Prediction and Experiment

    by Kostandin Gjika, Chris Groves, Luis San Andre´s, Gerald D. LaRue

    Current trends for advanced automotive engines focusing on downsizing, better fuel efficiency and lower emissions have led to several changes in turbocharger bearing systems design and technology. Automotive turbochargers run faster and use engine oils with very low viscosity under high oil inlet temperature and low feed pressure. The development of high performing bearing systems, marrying innovation with reliability, is a persistent challenge. This paper shows progress on the nonlinear dynamic behavior modeling of rotor-radial bearing system (RBS) incorporating two oil films in series: a hydrodynamic one with a squeeze film damper commonly used in turbochargers. The developed fluid bearing code predicts bearing rotational speed (in case of fully floating design), operating inner and outer bearing film clearances, effective oil viscosity taking into account its shear effect, and hydrostatic load. A rotordynamics code uses this input to predict the nonlinear lateral dynamic response of the rotor-bearing system. The model predictions are validated with test data acquired on a high speed turbocharger RBS of 6.0 mm journal diameter running up to 250,000 rpm (maximum speed), 5W30 oil type, 150 °C oil inlet temperature, and 4 bar oil feed pressure. The tests are conducted at a rotordynamics technology laboratory using a high performance data acquisition system. Turbochargers with four combinations of inner and outer RBS clearances are tested. Prediction and measured synchronous response and total motion are in good agreement. Both demonstrate the nonlinear character of RBS behavior including several subsynchronous frequencies components across the operating speed range. The non linear predictive model aids the development of high performance and optimized turbocharger RBS with faster development cycle times and increased reliability.


  • A Virtual Tool for Prediction of Turbocharger Nonlinear Dynamic Response: Validation Against Test Data

    by Luis San Andres, Juan Carlos Rivadeneira, Kostandin Gjika, Christopher Groves, Gerry LaRue

    Advances on the modeling of nonlinear rotor-bearing models for prediction of the dynamic shaft response of automotive turbochargers (TCs) supported on floating ring bearings (FRBs) are presented. Comprehensive test data for a TC unit operating to a top speed of 65 krpm serves to validate the model predictions. The static forced performance of the support FRBs considers lubricant thermal effects, thermal expansion of the shaft and bearings, and entrance pressure losses due to centrifugal flow effects. The bearing analysis also yields linearized rotordynamic force coefficients for the inner and outer lubricant films. These coefficients are used with the rotor model to predict the synchronous response to imbalance and the system natural frequencies and stability. A method renders an accurate estimation of the test rotor imbalance by using the actual vibration measurements and influence coefficients derived from predictions using linearized bearing force coefficients. Predicted ring rotational speeds, operating radial clearances and lubricant viscosities for the inner and outer films are the main input to the nonlinear time transient analysis. The nonlinear response model predicts the total shaft motion, with FFTs showing the synchronous response, and amplitudes and whirl frequencies of subsynchronous motions. The predicted synchronous amplitudes are in good agreement with the measurements, in particular at high shaft speeds. The nonlinear analysis predicts multiple frequency subsynchronous motions for speeds ranging from 10 krpm to 55 krpm (maximum speed 70 krpm), with amplitudes and frequencies that correlate well with the test data. The comparisons validate the comprehensive rotor-bearings model whose ultimate aim is to save TC design time and accelerate product development.


  • Nonlinear Rotordynamics of Automotive Turbochargers: Predictions and Comparisons to Test Data

    by Luis San Andre´s, Juan Carlos Rivadeneira, Murali Chinta, Kostandin Gjika, Gerry LaRue

    Passenger vehicle turbochargers (TCs) offer increased engine power and efficiency in an ever-competitive marketplace. Turbochargers operate at high rotational speeds and use engine oil to lubricate fluid film bearing supports (radial and axial). However, TCs are prone to large amplitudes of sub-synchronous shaft motion over wide ranges of their operating speed. Linear rotordynamic tools cannot predict the amplitudes and multiple frequency shaft motions. A comprehensive nonlinear rotordynamics model coupled to a complete fluid-film-bearing model solves in real time the dynamics of automotive turbochargers. The computational design tool predicts the limit cycle response for several inner and outer film clearances and operating conditions including rotor speed and lubricant feed pressure. Substantial savings in product development and prototype testing are the benefits of the present development. The paper presents predictions of the linear and nonlinear shaft motion of an automotive turbocharger supported on a semi-floating ring bearing. The shaft motion predictions are compared to measurements of shaft motion at the compressor nose for speeds up to 240 krpm, and for lubricant inlet pressure of 4 bar at 150°C. Linear and nonlinear rotordynamic models reproduce very well the test data for synchronous response to imbalance. The nonlinear results show two sub-synchronous whirl frequencies whose large magnitudes agree well with the measurements. A large side load predicted for this turbocharger must be considered for accurate prediction of the rotordynamic response.


  • Test Response of a Turbocharger Supported on Floating Ring Bearings: Part II — Comparisons to Nonlinear Rotordynamic Predictions

    by Chris Holt, Luis San Andre´s, Sunil Sahay, Peter Tang, Gerry La Rue, Kostandin Gjika

    Linear and nonlinear analysis results for the operation of a small automotive turbocharger supported on floating ring bearings are presented. A comprehensive fluid film bearing model predicting the forced response of floating ring bearings is also described. The linear rotordynamic model predicts well the rotor free-free modes and onset speed of instability using linearized bearing force coefficients. The nonlinear model incorporating instantaneous bearing reaction forces in the numerical integration of the rotor equations of motion predicts the limit cycle amplitudes with two fundamental sub synchronous whirl frequencies. Comparisons of both models to experimental results follow. The predictions evidence two unstable whirl ratios at approximately 1/2 ring speed and 1/2 ring speed plus 1/2 journal speed. The transient nonlinear responses reveal the importance of rotor imbalance in suppressing the subsynchronous instabilities at large rotor speeds as also observed in the experiments.


  • Test Response of a Turbocharger Supported on Floating Ring Bearings: Part I — Assessment of Subsynchronous Motions

    by Chris Holt, Luis San Andre´s, Sunil Sahay, Peter Tang, Gerry La Rue, Kostandin Gjika

    Measurements of casing acceleration on an automotive turbocharger running to a top speed of 115 krpm and driven by ambient temperature pressurized air are reported. Waterfall acceleration spectra versus rotor speed show the effects of increasing lubricant inlet pressure and temperature on the turbocharger rotordynamic response. A comprehensive analysis of the test data forwards regimes of speed operation with two subsynchronous whirl motions (rotordynamic instabilities). Increasing the lubricant feed pressure delays the onset speed of instability for the most severe subsynchronous motion. However, increasing the lubricant feed pressure also produces larger synchronous displacements. The effect of lubricant feed temperature is minimal on the onset and end speeds of rotordynamic instability. Nevertheless, operation with a cold lubricant exhibits lower amplitudes of motion, synchronous and subsynchronous. The experimental results show the subsynchronous frequencies of motion do not lock (whip) at system natural frequencies but continuously track the rotor speed. No instabilities (subsynchronous whirl) remain for operating speeds above 90 krpm. Bearings greatly influence turbocharger (TC) rotordynamic performance.