Li-Bo Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Li-Bo Zhang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Bing-Guo Liu
Yunnan Provincial Key Laboratory of Intensification Metallurgy , Kunming , Yunnan , China ; Key Laboratory of Unconventional Metallurgy, Ministry of Education , Kunming University of Science and Technology , Kunming , China ; Faculty of Metallurgical and Energy Engineering , Kunming University of Science and Technology , Kunming , China
1 shared publication- Chandrasekhar Srinivasakannan
Department of Chemical Engineering Khalifa University of Science and Technology Abu Dhabi UAE
1 shared publication Chen-Hui Liu
Yunnan Provincial Key Laboratory of Intensification Metallurgy , Kunming , Yunnan , China ; Key Laboratory of Unconventional Metallurgy, Ministry of Education , Kunming University of Science and Technology , Kunming , China ; Faculty of Metallurgical and Energy Engineering , Kunming University of Science and Technology , Kunming , China
1 shared publicationGuo Chen
Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming, Yunnan 650093, China
1 shared publicationHong-Ying Xia
Yunnan Provincial Key Laboratory of Intensification Metallurgy , Kunming , Yunnan , China ; Key Laboratory of Unconventional Metallurgy, Ministry of Education , Kunming University of Science and Technology , Kunming , China ; Faculty of Metallurgical and Energy Engineering , Kunming University of Science and Technology , Kunming , China
1 shared publicationHongbo Zhu
Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming, Yunnan 650093, China
1 shared publication
Latest Publications
- Open Access
- 11 September 2014
- Published by Walter de Gruyter GmbH in High Temperature Materials and Processes
- Vol. 34 (5) , 441-446
Oxidation of High Titanium Slag through Microwave Treatment
Due to its special nature of microwave heating, the reaction processes of high dielectric loss materials under microwave field draw more and more attention. This work attempts to figure out microwave oxidation process of high titanium slag. Based on a through analysis, it can be concluded that high titanium slag phase transformation process under microwave field can be divided into four stages: (i) crystallization of amorphous Fe, Mg, and Ti oxides, (ii) decomposition of Fe 0.5 Mg 0.5 Ti 2 O 5 , (iii) oxidation of (Mg 0.15 Ti 1.85 )O 5 and FeTi 2 O 5 , and (iv) transformation of A-TiO 2 , which is totally from the reaction process (M 3 O 5 → A-TiO 2 → R-TiO 2 ) under conventional resistance heating condition. In addition, when amorphous Fe, Mg, and Ti oxides crystallize, the Raman active vibration modes first was assigned to A-TiO 2 lattice, then dominated by R-TiO 2 lattice. And it is important to mention that with phase transformation, there will grow tumour form on the surface of sample, which eventually develops into squamous layers.
- 11 September 2014
- Published by Walter de Gruyter GmbH in High Temperature Materials and Processes
- Vol. 34 (5) , 441-446
Open AccessOxidation of High Titanium Slag through Microwave Treatment
Due to its special nature of microwave heating, the reaction processes of high dielectric loss materials under microwave field draw more and more attention. This work attempts to figure out microwave oxidation process of high titanium slag. Based on a through analysis, it can be concluded that high titanium slag phase transformation process under microwave field can be divided into four stages: (i) crystallization of amorphous Fe, Mg, and Ti oxides, (ii) decomposition of Fe 0.5 Mg 0.5 Ti 2 O 5 , (iii) oxidation of (Mg 0.15 Ti 1.85 )O 5 and FeTi 2 O 5 , and (iv) transformation of A-TiO 2 , which is totally from the reaction process (M 3 O 5 → A-TiO 2 → R-TiO 2 ) under conventional resistance heating condition. In addition, when amorphous Fe, Mg, and Ti oxides crystallize, the Raman active vibration modes first was assigned to A-TiO 2 lattice, then dominated by R-TiO 2 lattice. And it is important to mention that with phase transformation, there will grow tumour form on the surface of sample, which eventually develops into squamous layers.
- 16 January 2014
- Published by Taylor & Francis in Drying Technology
- Vol. 32 (3) , 328-338
Dielectric Properties and Optimization of Parameters for Microwave Drying of Petroleum Coke Using Response Surface Methodology
The dielectric properties of petroleum coke at five temperatures between 20 to 100 ∘ C, covering different moisture content levels at 2.45 GHz, were measured using an open-ended coaxial probe dielectric measurement system. The effects of drying temperature, duration of drying, and sample mass on the moisture content and dehydration rate of petroleum coke was assessed utilizing the response surface methodology. The dielectric constant, loss factor, and loss tangent were all found to increase nearly linearly with increase in moisture content. Three predictive empirical models were developed to relate the dielectric constant, loss factor, and loss tangent of petroleum coke as a linear function of moisture content from 3–10%. An increase in temperature between 20 to 100 ∘ C was found to increase the dielectric properties. The penetration depth was observed to increase linearly with decrease in moisture content in the range of 3 to 10%. A predictive empirical model was developed to calculate penetration depth for petroleum coke. Two mathematical models were established and analyzed using RSM to describe the relationship between the microwave drying conditions and the responses, moisture content, and dehydration rate. Statistical analysis with response surface regression showed that microwave drying temperature, duration of drying, and sample mass were significantly related to moisture content and dehydration rate. Based on the RSM analysis, the optimum process conditions were estimated to be a microwave drying temperature of 75 ∘ C, drying duration of 10 sec, and sample mass of 60 g, with the resultant moisture content being 0.34 at a dehydration rate of 2.94 g/min.
- 16 January 2014
- Published by Taylor & Francis in Drying Technology
- Vol. 32 (3) , 328-338
Dielectric Properties and Optimization of Parameters for Microwave Drying of Petroleum Coke Using Response Surface Methodology
The dielectric properties of petroleum coke at five temperatures between 20 to 100 ∘ C, covering different moisture content levels at 2.45 GHz, were measured using an open-ended coaxial probe dielectric measurement system. The effects of drying temperature, duration of drying, and sample mass on the moisture content and dehydration rate of petroleum coke was assessed utilizing the response surface methodology. The dielectric constant, loss factor, and loss tangent were all found to increase nearly linearly with increase in moisture content. Three predictive empirical models were developed to relate the dielectric constant, loss factor, and loss tangent of petroleum coke as a linear function of moisture content from 3–10%. An increase in temperature between 20 to 100 ∘ C was found to increase the dielectric properties. The penetration depth was observed to increase linearly with decrease in moisture content in the range of 3 to 10%. A predictive empirical model was developed to calculate penetration depth for petroleum coke. Two mathematical models were established and analyzed using RSM to describe the relationship between the microwave drying conditions and the responses, moisture content, and dehydration rate. Statistical analysis with response surface regression showed that microwave drying temperature, duration of drying, and sample mass were significantly related to moisture content and dehydration rate. Based on the RSM analysis, the optimum process conditions were estimated to be a microwave drying temperature of 75 ∘ C, drying duration of 10 sec, and sample mass of 60 g, with the resultant moisture content being 0.34 at a dehydration rate of 2.94 g/min.