Muriel Hantcherli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Muriel Hantcherli has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
A. Coujou
Centre National de la Recherche Scientifique
1 shared publicationA. Couret
Centre National de la Recherche Scientifique
1 shared publication- Alain Couret
CEMES, Université de Toulouse, CNRS, 29 rue Jeanne Marvig, BP 94347, 31055 Toulouse, France
1 shared publication - Benjamin Galy
CEMES, Université de Toulouse, CNRS, 29 rue Jeanne Marvig, BP 94347, 31055 Toulouse, France
1 shared publication - Christophe Deshayes
CEMES-CNRS, Université de Toulouse, 31055 Toulouse, France
1 shared publication F. Delmas
1 shared publication
Latest Publications
- Open Access
Microstructure, Plasticity and Ductility of a TNM+ Alloy Densified by Spark Plasma Sintering
This work presents a study of the microstructure and mechanical properties of a TNM+ alloy (Ti-43.5Al-4Nb-1Mo-0.1B-0.3C-0.3Si, in at.%) densified by Spark Plasma Sintering (SPS), in comparison to the as-SPSed TNM alloy, which contains neither carbon nor silicon. Tensile tests at room temperature and 800 °C, as well as creep tests at 800 °C and 200 MPa, were performed. The microstructures and the fracture surfaces of deformed samples were studied by scanning and transmission electron microscopies, as well as by X-ray diffraction. The deformation mechanisms were investigated by means of in situ straining experiments and post-mortem analyses of deformed samples, both performed by transmission electron microscopy. Contrary to the TNM alloy, the as-SPSed microstructure of the TNM+ alloy does not contain β/βo phase due to the incorporation of carbon. At room temperature, the TNM+ alloy exhibits a yield stress of 520 MPa but a poor ductility of less than 0.1% of plastic strain. The incorporation of carbon and silicon leads to an increase in the creep resistance of the alloy at 800 °C. Despite the fact that iron inclusions are responsible for the premature failure of some samples during tensile tests, the TNM+ alloy is found to be able to deform plastically at room temperature by the glide of ordinary dislocations and by twinning.
Open AccessMicrostructure, Plasticity and Ductility of a TNM+ Alloy Densified by Spark Plasma Sintering
This work presents a study of the microstructure and mechanical properties of a TNM+ alloy (Ti-43.5Al-4Nb-1Mo-0.1B-0.3C-0.3Si, in at.%) densified by Spark Plasma Sintering (SPS), in comparison to the as-SPSed TNM alloy, which contains neither carbon nor silicon. Tensile tests at room temperature and 800 °C, as well as creep tests at 800 °C and 200 MPa, were performed. The microstructures and the fracture surfaces of deformed samples were studied by scanning and transmission electron microscopies, as well as by X-ray diffraction. The deformation mechanisms were investigated by means of in situ straining experiments and post-mortem analyses of deformed samples, both performed by transmission electron microscopy. Contrary to the TNM alloy, the as-SPSed microstructure of the TNM+ alloy does not contain β/βo phase due to the incorporation of carbon. At room temperature, the TNM+ alloy exhibits a yield stress of 520 MPa but a poor ductility of less than 0.1% of plastic strain. The incorporation of carbon and silicon leads to an increase in the creep resistance of the alloy at 800 °C. Despite the fact that iron inclusions are responsible for the premature failure of some samples during tensile tests, the TNM+ alloy is found to be able to deform plastically at room temperature by the glide of ordinary dislocations and by twinning.
- 26 September 2012
- Published by EDP Sciences in Revue de Métallurgie
- Vol. 109 (6) , 415-422
Micro mécanismes du durcissement structural d’un alliage d’aluminium aéronautique
- 26 September 2012
- Published by EDP Sciences in Revue de Métallurgie
- Vol. 109 (6) , 415-422
Micro mécanismes du durcissement structural d’un alliage d’aluminium aéronautique