MDMartina Drdlová

Martina Drdlová

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Martina Drdlová has a total of 60 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Accelerated carbonation of low-lime calcium silicates: CaCO 3 seeding for polymorph control and strength enhancement

    by Martin Nguyen, T. Staněk, M. Sedlačík, M. Krejčí Kotlánová, D. Kubátová, M. Boháč, M. Drdlová, Z. Krejza, M. Pánek, L. Senye, et al.

  • Open Access

    The Analysis of Vehicle Security Barrier Parameters for Protecting the Infrastructure Against the Passenger Vehicle Impacts

    by Dávid Riedl, René Čechmánek, Martina Drdlová, Kamil Řehák, Pavel Kopeček, Jozef Dlugoš, Marek Šebík

    This study investigates the performance of mobile and permanent vehicle security barrier systems using finite element simulations under varying impact conditions. The primary objective is to evaluate the influence of barrier rotational angle relative to the vehicle impact direction and anchor placement on barrier performance, while identifying key mechanisms governing vehicle–barrier interaction that may support future barrier development. The proposed barrier system consists of modular units that also serve as flowerpots, representing a multifunctional concept that combines security performance with environmental and aesthetic functions. In addition to conventional assessment metrics such as final penetration and vehicle velocity, the adopted evaluation framework considers their evolution throughout the impact together with vehicle and barrier energy response, front axle motion, and anchor loading and failure. The results indicate that the proposed barrier configurations predominantly function as deceleration systems rather than fully effective restraint systems. The influence of barrier rotational angle on the permanent barrier was more pronounced at the lower impact velocity (15 km·h⁻¹) but diminished at higher impact velocities (50 and 80 km·h⁻¹), with maximum differences of approximately 440 mm in penetration and 2.6 km·h⁻¹ in final vehicle velocity. The influence of anchor placement alone was smaller, resulting in maximum differences of approximately 378 mm in penetration and 1 km·h⁻¹ in final vehicle velocity. Analysis of crash progression provided further insight into the relationship between anchorage failure, barrier mobilization, front axle motion, and changes in vehicle deceleration. These observations may support the further development and assessment of vehicle security barrier systems.

  • Open Access

    The comparison of projectile impact resistance of ultra-high-performance fibre-reinforced concrete with various aggregates

    by Martina Drdlová, Martin Šperl

    In order to apply the ultra-high-performance fibre-reinforced concrete (UHPFRC) in the constructions of ballistic protective structures, the impact resistance of UHPFRC has been investigated experimentally by conducting the high-speed projectile penetration tests. 5 mixtures with basalt and corundum aggregates with various grain size have been prepared and subjected to the quasi-static and 7.62 x 54R B32 API projectile impact load using the striking velocity of 850 m/s. The influence of the strength, size and material of the aggregate on the projectile impact resistance represented by differential efficiency factor (DEF), structural integrity and area and height of impact crater has been evaluated. The superior projectile resistance of UHPFRC with corundum has been observed. Regarding the size of the aggregates, the incorporation of coarser aggregates brings better projectile impact resistance.


  • Open Access

    High strain rate behaviour of fiber reinforced concrete

    by Miloslav Popovič, Jaroslav Buchar, Martina Drdlová

    The results of dynamic compression and tensile-splitting tests of concrete reinforced by randomly distributed short non – metallic fibres are presented. A Split Hopkinson Pressure Bar combined with a high-speed photographic system, was used to conduct dynamic Brazilian tests. Quasi static test show that the reinforcement of concrete by the non-metallic fibres leads to the improvement of mechanical properties at quasi static loading. This phenomenon was not observed at the high strain rate loading .Some explanation of this result is briefly outlined.

  • Dynamic behavior of cement-bonded wood-chip board

    by M. Popovič, M. Drdlová, M. Chadima, M. Šebík

    The cement-bonded wood-chip material is used in many civil applications as building material or noise protecting material. This investigation is a part of complex development of safety road barrier with integrated noise protecting wall. Any kind of this application has to comply withstrict conditions defined in national standards for safety on roads. Usually those standards prescribe very expensive crash tests. This development process can be supported with numerical simulation but detailed knowledge about material properties and behavior is necessary as an essential input. The cement-bonded wood-chip material properties were analyzed in this work. Set of real quasi-static and dynamic experiments was performed. The material model, created based on the obtained results, will be used in numerical simulation of crash test of mobile noise protection wall according EN1317.

  • FEM modelling of fibre-concrete in development of blast resistant elements

    by Martina Drdlová, Miloslav Popovič, René Čechmánek, Petr Bibora

    The paper summarizes the results of the development of fibre reinforced concrete intended for explosion resistant applications. Blast resistance of slurry infiltrated fibre concrete (SIFCON) with different amount and shape of fibres was investigated both experimentally and numerically. Test specimens with 2 types of steel fibres with different shape parameters in four volume fractions (2.5;5;7.5 and 10.0 vol. %) were investigated. Quasistatic mechanical properties have been determined and real blast test on the selected slab specimens were performed. The Finite Element (FE) method was used to predict the response of the slabs upon blast impact. New approach based on creation of the automatic scripts designed for generating of the FE network of fibre elements has been proposed and used. This approach enables creation of the FE model with various shape types and amounts of fibres. Calculations were performed in LS-Dyna solver. Using this concept, good agreement was concluded between the results of the real blast experiments and numerical simulations of slab specimens. The material characteristics and explosion test data have been used for numerical investigation, which defined the optimal wall composition and dimensions of the concrete element which should resist the explosion defined by type, size, weight and placement of the blast.

  • High Strain Rate Compressive Behavior of Micro-Fibre Reinforced Fine Grained Cementitious Composite

    by Martina Drdlová, Miloslav Popovič, René Čechmánek

    This paper presents an experimental study on the high strain rate compressive behavior of micro-fibre reinforced ultrahigh performance cementitious composite, which is intended to be used as a matrix for slurry infiltrated fibre concrete (SIFCON). Cementitious composite specimens with 5 different types of microfibres, namely aramid, carbon, wollastonite, polypropylene and glass in amounts of 1.5-2.0% by volume were prepared and investigated. Split Hopkinson pressure bar (SHPB) equipment was used to determine the cementitious composite behavior at strain rates up to 1600 s-1. Quasistatic tests were performed, as well and ratios of these properties at high strain rates to their counterparts at static loading were compared. The dynamic increase factors were calculated. Strain rate sensitivity was observed - compressive strength was found to be increased with strain rate for all tested specimens. Peak stress values, critical compressive strain and post peak behaviour varies for specimens with different micro-fibre reinforcement, which allows to find the optimal reinforcement for high strain rate impacted structures.

  • Open Access

    Blast resistance of slurry infiltrated fibre concrete with hybrid fibre reinforcement

    by M Drdlová, P Bibora, R Čechmánek

    This paper investigates experimentally the blast resistance of slurry infiltrated fibre concrete (SIFCON) with hybrid fibre reinforcement realized by various combinations of polypropylene (PP), aramid, carbon, glass, wollastonite and steel fibers. The binary reinforcement systems were designed using the combinations of steel/PP, steel/aramid, steel/glass, steel/wollastonite and steel/carbon fibres with various fibre geometry. Six different batches (including one reference specimen) were examined with aim to determine the influence of the parameters of hybrid reinforcement on blast resistance of the concrete. Mechanical parameters at quasistatic load (flexural strength, compressive strength) were determined and load-deflection curves were captured. Real blast tests were performed on the slab specimens (500 × 500 × 40 mm) according to the modified methodology M-T0-VTU0 10/09. The change of the ultrasonic wave transit time before and after the blast load in certain measurement points, damage of the slab, the weight of fragments and their damage potential were evaluated and compared. The results indicate, that hybrid fibre reinforcement, when properly designed, can highly enhance overall blast resistance of SIFCON and can significantly reduce the spalling. Steel-aramid combination brought the best blast resistance.


  • Open Access

    New perspective material for building envelopes

    by R Cechmanek, M Drdlova, V Prachar

    Thin-walled fibre-cement elements are widely used in residential and industrial buildings for their appearance and durability. Because they are made of light-weight materials, they are mostly used as cladding elements for façades of multi-storey buildings exposed to hard external conditions. Nevertheless, there are still demands from architects and building companies to decrease their weight for reducing manufacturing, transport and assembly costs. In one part of our research light-weighing possibilities of standard composition were evaluated by means of porous structure creation. In the second part the standard aggregate was substituted with available kinds of light-weight porous aggregates in a certain part or in a whole volume. As the limit criterion there was maximal particle size 1 mm for spraying of fibre-cement mixture by means of special air pressure equipment. From the range of possible fillers with different material properties granulated expanded glass worked the best. This paper brings not only a summary of laboratory experiments but also examples of successful realizations such as balcony panelboards, façade elements, bridge structure cladding elements or bulk flower pots. Even though these are not structural elements, it was necessary to evaluate also strength characteristics and resistance to environment for their durability in certain applications.