XXXiaojun Xu

Xiaojun Xu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xiaojun Xu has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    High-Output Hydraulic Robotic Joints: Architecture, Coupled Physics, Integration, and Task-Usable Performance

    by Cuiya Liu, Xiaojun Xu, Min Wang, Guojun Qin, Junhong Yang, Qing Guo

    Hydraulic actuation can deliver substantial force or torque within a restricted robotic limb, yet installed joint capability emerges from more than actuator pressure. This critical engineering review connects mechanical output mechanism, hydraulic source placement, installation site, and runtime hydraulic capacity in a multidimensional architecture taxonomy. Representative hardware spans legged and wheel-legged robots, humanoids, wearable systems, and manipulators. Pressure–area, flow–speed, and virtual-work relations are interpreted together with containment stress, fluid and structural compliance, leakage, friction, and heat rejection to explain the usable output envelope. Integration is treated as a redistribution of fluid-path volume, moving mass, losses, thermal load, and service interfaces across shared sources, embedded passages, valve-integrated modules, and electro-hydrostatic actuators. Task-usable joint capability is defined through hardware, operating-condition, energy-conversion, and validation boundaries. A source-specific evidence matrix shows that pressure and output are commonly reported, whereas matched output, efficiency, installed-boundary clarity, and duty qualification remain substantially less complete. The review therefore links architecture-conditioned physics to evidence-aware benchmarking and proposes measurable research priorities for high-pressure tribology, thermal management, lightweight integration, reconfiguration, sensing, and robot-level validation.

  • Open Access

    Hydrodynamic Performance and Bucket-Controlled Turning Optimization of an Amphibious Rescue and Operation Platform with Detachable Floating Boxes

    by Junjie Li, Bolong Liu, Xiaojun Xu, Yaxin Xie

    This study investigates the hydrodynamic behavior of an amphibious rescue and operation platform equipped with detachable floating boxes and a front bucket system, and it further develops a control-oriented turning optimization framework for a two-bucket steering configuration. Calm-water resistance, free-surface evolution, running attitude, and roll decay were analyzed using a Reynolds-averaged Navier–Stokes/volume-of-fluid solver with overset grids and dynamic fluid–body interaction. Straight-ahead non-rotating cases were computed using a symmetry-based half-domain model, whereas roll- and turning-related cases were simulated in the full domain. The numerical method was validated against towing-tank data for a benchmark amphibious vehicle, and the predicted resistance showed an overall deviation of 2.11%. The results show that the detachable floating boxes slightly increase resistance at 2 km/h, but reduce resistance by approximately 11.4% at 8 km/h owing to favorable wave interference. They also reduce trim and heave over the investigated speed range and markedly improve transverse stability, with the roll motion decaying to nearly zero within about 20 s. By contrast, the installation of the bucket substantially increases hydrodynamic resistance; at the design cruising speed of 8 km/h, the resistance increase reaches about 74.4%, while a bucket-induced bow-down moment modifies the running attitude and suppresses heave. At cruising speed, the bucket swing-arm angle has a non-monotonic influence: the resistance reaches a local peak near 6°, the minimum resistance is obtained at 20°, and the smallest trim is achieved at 4°. Based on these findings, a symmetry-preserving hydrodynamic surrogate and a constrained optimization strategy were established for bucket-controlled turning-radius allocation. The results indicate that differential bucket motion is the primary steering mechanism, whereas the bucket-arm angle provides secondary steering amplification at the cost of additional drag. The present study provides an integrated hydrodynamic basis for the design, operation, and steering-oriented control allocation of amphibious rescue platforms.

  • Open Access

    Optimization of Grouser–Track Structural Parameters for Enhanced Tractive Performance in Unmanned Amphibious Tracked Vehicles

    by Yaoyao Chen, Xiaojun Xu, Wenhao Wang, Xue Gao, Congnan Yang

    This study focuses on optimizing track and grouser structural parameters to enhance UATV drawbar pull, particularly under soft soil conditions. A numerical soil thrust model for single-track shoes was developed based on track–soil interaction mechanics, revealing distinct mechanistic roles: track structural parameters (length/width) govern pressure–sinkage relationships at the track base, while grouser structural parameters (height, spacing, V-shaped angle) dominate shear stress–displacement dynamics on grouser shear planes. A novel DEM-MBD coupling simulation framework was established through soil parameter calibration and multi-body dynamics modeling, demonstrating that soil thrust increases with grouser height and V-shaped angle, but decreases with spacing, with grouser height exhibiting the highest sensitivity. A soil bin test validated the numerical model’s accuracy and the coupling method’s efficacy. Parametric optimization via the Whale Optimization Algorithm (WOA) achieved a 55.86% increase in drawbar pull, 40.38% reduction in ground contact pressure and 57.33% improvement in maximum gradability. These advancements substantially improve the tractive performance of UATVs in soft beach terrains. The proposed methodology provides a systematic framework for amphibious vehicle design, integrating numerical modeling, high-fidelity simulation, and experimental validation.


  • Open Access

    Optimization of Grouser-Track Structural Parameters for Enhanced Tractive Performance in Unmanned Amphibious Tracked Vehicles

    by Yaoyao Chen, Xiaojun Xu, Wenhao Wang, Xue Gao, Congnan Yang

    The tractive performance of Unmanned Amphibious Tracked Vehicles (UATV) is critical for executing towing operations in coastal environments. This study focuses on optimizing track and grouser structural parameters to enhance UATV drawbar pull, particularly under soft soil conditions. A numerical soil thrust model for single-track shoes was developed based on track-soil interaction mechanics, revealing distinct mechanistic roles: track structural parameters (length/width) govern pressure-sinkage relationships at the track base, while grouser structural parameters (height, spacing, V-shaped angle) dominate shear stress-displacement dynamics on grouser shear planes. A novel DEM-MBD coupling simulation framework was established through soil parameter calibration and multi-body dynamics modeling, demonstrating that soil thrust increases with grouser height and V-shaped angle, but decreases with spacing with grouser height exhibiting the highest sensitivity. Soil bin test validated the numerical model’s accuracy and the coupling method’s efficacy. Parametric optimization via the Whale Optimization Algorithm (WOA) achieved a 55.86% increase in drawbar pull, 4.04% reduction in ground contact pressure and 57.33% improvement in maximum gradability. These advancements significantly enhance UATV tractive performance in beach areas. The proposed methodology provides a systematic framework for amphibious vehicle design, integrating numerical modeling, high-fidelity simulation, and experimental validation.

  • Amphibious vehicle's resistance optimization through neural networks and genetic algorithms

    by Bolong Liu, Yifan Zhang, Dibo Pan, Xiaojun Xu, Tong Cai

    Amphibious vehicles, as a new type of aquatic and terrestrial transport platform, are increasingly involved in the existing transportation system. Resistance is a key factor that affects the efficiency and energy consumption of vehicles in aquatic sailing. Resistance reduction optimization design is a focal point and challenge in the design process of amphibious vehicles. In this paper, a resistance performance optimization method has been proposed based on neural networks and genetic algorithms. First, key parameters for the shape design are extracted based on a thorough understanding of the vehicle's performance. These parameters are used to construct a parameterized design space. Second, a training set is obtained based on the Latin hypercube sampling method and numerical calculation methods, and a test set is randomly generated. To achieve better resistance prediction performance, a method based on the genetic algorithm-optimized backpropagation Neural Network is proposed. Next, the resistance performance of the two operating conditions is optimized through the non-dominated sorting genetic algorithm II, and optimized configuration parameters are obtained, which has a 22.71% energy-saving ratio at cruising speed. Finally, the optimized configuration is analyzed using numerical calculation methods to validate the resistance prediction and optimization methods.


  • Study and optimization of a deformable trimaran amphibious transport vehicle's resistance characteristic

    by Bolong Liu, Dibo Pan, Xiaojun Xu

    Amphibious transport vehicles have increasingly become an important tool for connecting water and land transportation, serving both water and land transport missions. However, due to the unique shape of amphibious vehicles, their sailing resistance is high, which severely restricts their widespread use. In this paper, a deformable trimaran amphibious transport vehicle with retractable side hulls is designed. Based on the Reynolds-averaged Navier–Stokes equation, a resistance prediction method for amphibious vehicles is established and verified through towing experiments. The resistance characteristic of the trimaran vehicle is studied and optimized. First, the effects of the side hull and its position on resistance performance are analyzed, and the sensitivity of position parameters is evaluated. Then, the bow plate angle on resistance is analyzed. Finally, a surrogate model of the side hull position parameters and the bow plate angle with resistance is established using the Kriging method. The Particle Swarm Optimization is used to search for the minimum resistance configuration Opt 2, which achieves a drag reduction effect of 19.84% at the design speed.


  • Open Access

    Research on launching, water exiting, and river crossing of an amphibious vehicle

    by Bolong Liu, Xiaojun Xu, Dibo Pan

    The main focus of this paper is the amphibious vehicle's water-land trans-media capability, specifically its ability to efficiently carry out transportation tasks in rivers and nearshore areas. This capability relies on three key processes: launching, water exiting, and river crossing. To study these processes, hydrodynamic numerical simulations are conducted. The Reynolds-averaged Navier–Stokes) equation, simplified terra mechanics model, and body force method are adopted to analyze the trans-media and self-propulsion processes. Results indicate that the optimal launching speed is around 15 km/h, with a stable trim and heave, and a launching angle range of 15°–25° for insubmersibility and stability. Furthermore, high-speed water exiting enhances insubmersibility and imposes lower requirements on road adhesion conditions, outperforming low-speed water exiting. In terms of self-propelled river crossing, higher heading angles and faster river currents improve hydrodynamic lift, with the fastest crossing achieved at a 10° heading angle for a current speed of 2.5 m/s and a forward speed of 30 km/h.


  • Open Access

    Numerical analysis on hydrodynamic performance and hydrofoil optimization for amphibious vehicles

    by Dibo Pan, Xiaojun Xu, Bolong Liu

    A numerical approach is established to study the hydrodynamic performance using an amphibious transport vehicle (ATV) as a research object. Numerical calculation based on the Reynolds average Navier–Stokes method is studied in terms of first layer grid height, surface meshing partition scale, and prismatic layer coefficient. Through uncertainty analysis, the correctness and convergence of the numerical approach are verified. Towing tests are conducted to compare the experimental data with the simulation results, which validated the reliability of the numerical approach under all working conditions. Results show that the numerical approach will affect the simulated results, with an average error of 3.91% for the resistance and 4.21% for the trim, meeting the requirements for analysis accuracy. Based on the proposed numerical approach, an optimization design is carried out to improve the hydrodynamic performance of the ATV. Effects of bow plate angle, stern flap angle, and stern flap install height are studied. Latin hypercube is used for sampling in optimization design, and the Kriging method is applied to establish an approximate model. The cross-validation is carried out using the leave-one-out method. Particle swarm optimization is used for parameter optimization, and the optimized configuration is verified using the numerical approach. Results indicate that the combination of bow plate and stern flap shows excellent improvement in the hydrodynamic performance of amphibious vehicles. Numerical error of the approximate model is only 0.292%, which fully verifies its accuracy and effectiveness. The optimized ATV configuration shows the best drag reduction performance of 38.81% compared to the original model.


  • Drag reduction design and research of high-speed amphibious vehicle’s deformable track wheels

    by Bolong Liu, Xiaojun Xu, Dibo Pan, Yikun Feng, Shengyang Lu

    In this study, the resistance characteristics of the amphibious vehicle in the transitional stage are studied. A deformable track wheel is designed and its effect on the amphibious vehicle’s resistance is studied. The numerical calculation method based on the RANS solver and the towing test method is used to analyse the hydrodynamic performance of the amphibious vehicle. Based on the comparison of the vehicle model with no wheel, the influence of wheels on additional resistance at the groove fault is studied. The inclination angles of the front and rear deformation wheels are studied respectively. The influence and principle of the track wheel configuration on drag are analysed and expounded in terms of pressure distribution, water climbing and spray on the wheel grooves, and the hull attitude. Finally, an adjustment strategy of the deformable configuration wheel in the transition stage is proposed.


  • Open Access

    Track Design of Track-Wheel Transport Vehicle and Strength Analysis of Important Components

    by Yuchuan Yang, Tong Cai, Xiaojun Xu

    Through the comparative analysis of different types of transport vehicles, the paper puts forward the concept of Track-Wheel transport vehicles and expounds the crawler travel mechanism of the wheel-shift interchange transport vehicles. It is concluded that the Track-Wheel transport vehicle has the advantage of operating in harsh environments such as mud and sand. The article designs the track mechanism and focuses on the strength checks of the important components of the track walking mechanism, namely the track, the load wheel and the load wheel axle. And it is concluded that under the maximum load, the track, the load wheel and the load wheel axle can meet the bearing requirements.