Dibo Pan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dibo Pan has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Bolong Liu
College of Intelligence Science and Technology, National University of Defense Technology, Changsha 410073, China
12 shared publications Xiaojun Xu
6 shared publications- Xiaojun Xu
College of Intelligence Science and Technology, National University of Defense Technology, Changsha 410073, China
5 shared publications Haijun Xu
3 shared publicationsCongnan Yang
College of Intelligence Science, National University of Defense Technology, Hunan, China
2 shared publications- Yaxin Xie
National University of Defense Technology
2 shared publications
Latest Publications
- 28 May 2026
- Published by Springer Nature
- p. 193-200
Investigation into the Hydrodynamic Characteristics of Wheel-Track Amphibious Vehicles
- 28 May 2026
- Published by Springer Nature
- p. 193-200
Investigation into the Hydrodynamic Characteristics of Wheel-Track Amphibious Vehicles
- 1 June 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (6)
Amphibious vehicle's resistance optimization through neural networks and genetic algorithms
Amphibious vehicles, as a new type of aquatic and terrestrial transport platform, are increasingly involved in the existing transportation system. Resistance is a key factor that affects the efficiency and energy consumption of vehicles in aquatic sailing. Resistance reduction optimization design is a focal point and challenge in the design process of amphibious vehicles. In this paper, a resistance performance optimization method has been proposed based on neural networks and genetic algorithms. First, key parameters for the shape design are extracted based on a thorough understanding of the vehicle's performance. These parameters are used to construct a parameterized design space. Second, a training set is obtained based on the Latin hypercube sampling method and numerical calculation methods, and a test set is randomly generated. To achieve better resistance prediction performance, a method based on the genetic algorithm-optimized backpropagation Neural Network is proposed. Next, the resistance performance of the two operating conditions is optimized through the non-dominated sorting genetic algorithm II, and optimized configuration parameters are obtained, which has a 22.71% energy-saving ratio at cruising speed. Finally, the optimized configuration is analyzed using numerical calculation methods to validate the resistance prediction and optimization methods.
- 1 June 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (6)
Amphibious vehicle's resistance optimization through neural networks and genetic algorithms
Amphibious vehicles, as a new type of aquatic and terrestrial transport platform, are increasingly involved in the existing transportation system. Resistance is a key factor that affects the efficiency and energy consumption of vehicles in aquatic sailing. Resistance reduction optimization design is a focal point and challenge in the design process of amphibious vehicles. In this paper, a resistance performance optimization method has been proposed based on neural networks and genetic algorithms. First, key parameters for the shape design are extracted based on a thorough understanding of the vehicle's performance. These parameters are used to construct a parameterized design space. Second, a training set is obtained based on the Latin hypercube sampling method and numerical calculation methods, and a test set is randomly generated. To achieve better resistance prediction performance, a method based on the genetic algorithm-optimized backpropagation Neural Network is proposed. Next, the resistance performance of the two operating conditions is optimized through the non-dominated sorting genetic algorithm II, and optimized configuration parameters are obtained, which has a 22.71% energy-saving ratio at cruising speed. Finally, the optimized configuration is analyzed using numerical calculation methods to validate the resistance prediction and optimization methods.
- 1 April 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (4)
Study and optimization of a deformable trimaran amphibious transport vehicle's resistance characteristic
Amphibious transport vehicles have increasingly become an important tool for connecting water and land transportation, serving both water and land transport missions. However, due to the unique shape of amphibious vehicles, their sailing resistance is high, which severely restricts their widespread use. In this paper, a deformable trimaran amphibious transport vehicle with retractable side hulls is designed. Based on the Reynolds-averaged Navier–Stokes equation, a resistance prediction method for amphibious vehicles is established and verified through towing experiments. The resistance characteristic of the trimaran vehicle is studied and optimized. First, the effects of the side hull and its position on resistance performance are analyzed, and the sensitivity of position parameters is evaluated. Then, the bow plate angle on resistance is analyzed. Finally, a surrogate model of the side hull position parameters and the bow plate angle with resistance is established using the Kriging method. The Particle Swarm Optimization is used to search for the minimum resistance configuration Opt 2, which achieves a drag reduction effect of 19.84% at the design speed.
- 1 April 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (4)
Study and optimization of a deformable trimaran amphibious transport vehicle's resistance characteristic
Amphibious transport vehicles have increasingly become an important tool for connecting water and land transportation, serving both water and land transport missions. However, due to the unique shape of amphibious vehicles, their sailing resistance is high, which severely restricts their widespread use. In this paper, a deformable trimaran amphibious transport vehicle with retractable side hulls is designed. Based on the Reynolds-averaged Navier–Stokes equation, a resistance prediction method for amphibious vehicles is established and verified through towing experiments. The resistance characteristic of the trimaran vehicle is studied and optimized. First, the effects of the side hull and its position on resistance performance are analyzed, and the sensitivity of position parameters is evaluated. Then, the bow plate angle on resistance is analyzed. Finally, a surrogate model of the side hull position parameters and the bow plate angle with resistance is established using the Kriging method. The Particle Swarm Optimization is used to search for the minimum resistance configuration Opt 2, which achieves a drag reduction effect of 19.84% at the design speed.
- Open Access
- 1 November 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (11)
Research on launching, water exiting, and river crossing of an amphibious vehicle
The main focus of this paper is the amphibious vehicle's water-land trans-media capability, specifically its ability to efficiently carry out transportation tasks in rivers and nearshore areas. This capability relies on three key processes: launching, water exiting, and river crossing. To study these processes, hydrodynamic numerical simulations are conducted. The Reynolds-averaged Navier–Stokes) equation, simplified terra mechanics model, and body force method are adopted to analyze the trans-media and self-propulsion processes. Results indicate that the optimal launching speed is around 15 km/h, with a stable trim and heave, and a launching angle range of 15°–25° for insubmersibility and stability. Furthermore, high-speed water exiting enhances insubmersibility and imposes lower requirements on road adhesion conditions, outperforming low-speed water exiting. In terms of self-propelled river crossing, higher heading angles and faster river currents improve hydrodynamic lift, with the fastest crossing achieved at a 10° heading angle for a current speed of 2.5 m/s and a forward speed of 30 km/h.
- 1 November 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (11)
Open AccessResearch on launching, water exiting, and river crossing of an amphibious vehicle
The main focus of this paper is the amphibious vehicle's water-land trans-media capability, specifically its ability to efficiently carry out transportation tasks in rivers and nearshore areas. This capability relies on three key processes: launching, water exiting, and river crossing. To study these processes, hydrodynamic numerical simulations are conducted. The Reynolds-averaged Navier–Stokes) equation, simplified terra mechanics model, and body force method are adopted to analyze the trans-media and self-propulsion processes. Results indicate that the optimal launching speed is around 15 km/h, with a stable trim and heave, and a launching angle range of 15°–25° for insubmersibility and stability. Furthermore, high-speed water exiting enhances insubmersibility and imposes lower requirements on road adhesion conditions, outperforming low-speed water exiting. In terms of self-propelled river crossing, higher heading angles and faster river currents improve hydrodynamic lift, with the fastest crossing achieved at a 10° heading angle for a current speed of 2.5 m/s and a forward speed of 30 km/h.
- Open Access
- 1 August 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (8)
Numerical analysis on hydrodynamic performance and hydrofoil optimization for amphibious vehicles
A numerical approach is established to study the hydrodynamic performance using an amphibious transport vehicle (ATV) as a research object. Numerical calculation based on the Reynolds average Navier–Stokes method is studied in terms of first layer grid height, surface meshing partition scale, and prismatic layer coefficient. Through uncertainty analysis, the correctness and convergence of the numerical approach are verified. Towing tests are conducted to compare the experimental data with the simulation results, which validated the reliability of the numerical approach under all working conditions. Results show that the numerical approach will affect the simulated results, with an average error of 3.91% for the resistance and 4.21% for the trim, meeting the requirements for analysis accuracy. Based on the proposed numerical approach, an optimization design is carried out to improve the hydrodynamic performance of the ATV. Effects of bow plate angle, stern flap angle, and stern flap install height are studied. Latin hypercube is used for sampling in optimization design, and the Kriging method is applied to establish an approximate model. The cross-validation is carried out using the leave-one-out method. Particle swarm optimization is used for parameter optimization, and the optimized configuration is verified using the numerical approach. Results indicate that the combination of bow plate and stern flap shows excellent improvement in the hydrodynamic performance of amphibious vehicles. Numerical error of the approximate model is only 0.292%, which fully verifies its accuracy and effectiveness. The optimized ATV configuration shows the best drag reduction performance of 38.81% compared to the original model.
- 1 August 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (8)
Open AccessNumerical analysis on hydrodynamic performance and hydrofoil optimization for amphibious vehicles
A numerical approach is established to study the hydrodynamic performance using an amphibious transport vehicle (ATV) as a research object. Numerical calculation based on the Reynolds average Navier–Stokes method is studied in terms of first layer grid height, surface meshing partition scale, and prismatic layer coefficient. Through uncertainty analysis, the correctness and convergence of the numerical approach are verified. Towing tests are conducted to compare the experimental data with the simulation results, which validated the reliability of the numerical approach under all working conditions. Results show that the numerical approach will affect the simulated results, with an average error of 3.91% for the resistance and 4.21% for the trim, meeting the requirements for analysis accuracy. Based on the proposed numerical approach, an optimization design is carried out to improve the hydrodynamic performance of the ATV. Effects of bow plate angle, stern flap angle, and stern flap install height are studied. Latin hypercube is used for sampling in optimization design, and the Kriging method is applied to establish an approximate model. The cross-validation is carried out using the leave-one-out method. Particle swarm optimization is used for parameter optimization, and the optimized configuration is verified using the numerical approach. Results indicate that the combination of bow plate and stern flap shows excellent improvement in the hydrodynamic performance of amphibious vehicles. Numerical error of the approximate model is only 0.292%, which fully verifies its accuracy and effectiveness. The optimized ATV configuration shows the best drag reduction performance of 38.81% compared to the original model.
- 16 February 2023
- Published by Elsevier in Ocean Engineering
- Vol. 272
Influence of towing position on hydrodynamic characteristics of an Amphibious Tractor
- 16 February 2023
- Published by Elsevier in Ocean Engineering
- Vol. 272
Influence of towing position on hydrodynamic characteristics of an Amphibious Tractor
- 24 November 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 382
Research on shipping energy-saving technology: Hydrofoil amphibious vehicle driven by waterjet propulsion
- 24 November 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 382
Research on shipping energy-saving technology: Hydrofoil amphibious vehicle driven by waterjet propulsion
- 29 June 2022
- Published by Taylor & Francis in Ships and Offshore Structures
- Vol. 18 (7) , 970-979
Drag reduction design and research of high-speed amphibious vehicle’s deformable track wheels
In this study, the resistance characteristics of the amphibious vehicle in the transitional stage are studied. A deformable track wheel is designed and its effect on the amphibious vehicle’s resistance is studied. The numerical calculation method based on the RANS solver and the towing test method is used to analyse the hydrodynamic performance of the amphibious vehicle. Based on the comparison of the vehicle model with no wheel, the influence of wheels on additional resistance at the groove fault is studied. The inclination angles of the front and rear deformation wheels are studied respectively. The influence and principle of the track wheel configuration on drag are analysed and expounded in terms of pressure distribution, water climbing and spray on the wheel grooves, and the hull attitude. Finally, an adjustment strategy of the deformable configuration wheel in the transition stage is proposed.
- 29 June 2022
- Published by Taylor & Francis in Ships and Offshore Structures
- Vol. 18 (7) , 970-979
Drag reduction design and research of high-speed amphibious vehicle’s deformable track wheels
In this study, the resistance characteristics of the amphibious vehicle in the transitional stage are studied. A deformable track wheel is designed and its effect on the amphibious vehicle’s resistance is studied. The numerical calculation method based on the RANS solver and the towing test method is used to analyse the hydrodynamic performance of the amphibious vehicle. Based on the comparison of the vehicle model with no wheel, the influence of wheels on additional resistance at the groove fault is studied. The inclination angles of the front and rear deformation wheels are studied respectively. The influence and principle of the track wheel configuration on drag are analysed and expounded in terms of pressure distribution, water climbing and spray on the wheel grooves, and the hull attitude. Finally, an adjustment strategy of the deformable configuration wheel in the transition stage is proposed.
- 16 February 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 236 (7) , 3772-3789
Analysis of circumferential oil film thickness for piston ring in twin-rotor piston engine under differential velocity motion of combined annular cylinder
In this paper, a novel type of twin-rotor piston engine (TRPE) is proposed, and the circumferential oil film thickness for the piston ring in TRPE is analysed. Different from the integrated cylinder of a typical engine, the combined annular cylinder (CAC) of TRPE has unique structural composition and differential velocity motion characteristic, making the tribological performance more complicated. The main purpose of this paper is to reveal and explain the special tribological performance of TRPE, which has never been studied. Firstly, the special structural composition of CAC is introduced and the relative velocity between the piston ring and CAC wall at different circumferential positions of the piston ring is analysed. Then, based on the Greenwood-Trip asperity contact theory, radial and axial quasi-static equilibrium equations of the piston ring are both derived. The circumferential oil film thickness is calculated by solving the equilibrium equations and the two-dimensional average Reynolds equation within a cycle. Results indicate that there are significant differences in circumferential oil film thickness of the piston ring due to the special structure and motion of CAC, and the differences become greater as the output shaft speed increases. A long-time engine reverse towing experiment shows an obvious uneven wear phenomenon of the piston ring and CAC wall, which well validates the simulation results of the circumferential oil film thickness. The research work can be used as the basis of equal-wear design for the piston ring in TRPE with the help of surface texture technology, thereby greatly reducing the wear loss.
- 16 February 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 236 (7) , 3772-3789
Analysis of circumferential oil film thickness for piston ring in twin-rotor piston engine under differential velocity motion of combined annular cylinder
In this paper, a novel type of twin-rotor piston engine (TRPE) is proposed, and the circumferential oil film thickness for the piston ring in TRPE is analysed. Different from the integrated cylinder of a typical engine, the combined annular cylinder (CAC) of TRPE has unique structural composition and differential velocity motion characteristic, making the tribological performance more complicated. The main purpose of this paper is to reveal and explain the special tribological performance of TRPE, which has never been studied. Firstly, the special structural composition of CAC is introduced and the relative velocity between the piston ring and CAC wall at different circumferential positions of the piston ring is analysed. Then, based on the Greenwood-Trip asperity contact theory, radial and axial quasi-static equilibrium equations of the piston ring are both derived. The circumferential oil film thickness is calculated by solving the equilibrium equations and the two-dimensional average Reynolds equation within a cycle. Results indicate that there are significant differences in circumferential oil film thickness of the piston ring due to the special structure and motion of CAC, and the differences become greater as the output shaft speed increases. A long-time engine reverse towing experiment shows an obvious uneven wear phenomenon of the piston ring and CAC wall, which well validates the simulation results of the circumferential oil film thickness. The research work can be used as the basis of equal-wear design for the piston ring in TRPE with the help of surface texture technology, thereby greatly reducing the wear loss.