Ke Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ke Wu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Bing-Jie Lu
School of Biology, Food and Environment, Hefei University, Hefei 230601, China
2 shared publications- Haiyang Yan
CAS Key Laboratory of Soft Matter Chemistry, Collaborative Innovation Center of Chemistry for Energy Materials, School of Chemistry and Material Science, University of Science and Technology of China, Hefei 230026, China
2 shared publications - Jie Jin
Hefei Institute of Environmental Engineering, Hefei University, Hefei 230601, China
2 shared publications - Lei Hong
School of Biology, Food and Environment, Hefei University, Hefei 230601, China
2 shared publications - Teng Bao
School of Biology, Food and Environment, Hefei University, Hefei 230601, China
2 shared publications - Wenjie Gao
Collaborative Innovation Center for Environmental Pollution Control and Ecological Restoration of Anhui Province, School of Biology, Food and Environment, Hefei University, Hefei 230601, China
2 shared publications
Latest Publications
- Open Access
Spatial–Temporal Distribution and Ecological Risk Assessment of Microplastics in the Shiwuli River
This study aimed to investigate the distribution of microplastics (MPs) within the Shiwuli River in Hefei, a Chinese inland city. Water and sediment samples were collected during flood season (from May to September) and non-flood season (from October to April) at 10 representative points along the truck stream. The electron microscope, the laser direct infrared chemical imaging system (LDIR), and the scanning electron microscope (SEM) were used to observe and quantify the colour and shape of the MPs, to identify the number, size, and polymer composition of the MPs, and to observe the microstructures of typical MP particles, respectively. The polymer risk index (RI) model and the pollution load index (PLI) model were used to assess the polymer-related risks and the overall extent of MP pollution in the river, respectively. Analysis of MP abundance for different sampling points showed that the water of Shiwuli River had an average abundance of MPs of 8.4 ± 2.5 particles/L during the flood season and 5.8 ± 1.7 particles/L during the non-flood season; the sediment had an average abundance of MPs of 78.9 ± 8.3 particles/kg during the flood season and 63.9 ± 7.1 particles/kg during the non-flood season. The abundance of MPs of different points was investigated. Result show that the more abundances of MPs were found at confluences with tributaries (S4, S5, and S6), where they are also close to the residential and industrial development, while lower values were found in agricultural areas (S8) and wetland ecological regions (S9 and S10). In water, the maximum appeared at S5 with 21.7 ± 4.6 particles/L during the flood season and 15.9 ± 4.2 particles/L during the non-flood season, respectively; the minimum appeared at S9 with 1.8 ± 1.0 particles/L during the flood season and 2.2 ± 0.4 particles/L during the non-flood season, respectively. In sediment, the maximum appeared at S5 with 174.1 ± 10.1 particles/kg during the flood season and 143.6 ± 10.4 particles/kg during the non-flood season, respectively; the minimum appeared at S8 with 10.3 ± 2.8 particles/kg during the flood season and at S9 with 12.1 ± 3.2 particles/kg during the non-flood season, respectively. MP characteristics were also studied. Results show that the MPs mainly exhibited a fibroid morphology (27.90–34%), and red-coloured particles (19.10%) within the smaller size less than 500 μm (38.60%) were more prevalent. Additionally, the result of LDIR scanning shows that a total of eleven types of MP polymers were found in the river water and sediment, including acrylates (ACR), chlorinated polyethylene (CPE), ethylene vinyl acetate (EVA), polyethylene (PE), polyethylene terephthalate (PET), polypropylene (PP), polystyrene (PS), polyurethane (PU), polyvinylchloride (PVC), polyamide (PA), and silicon. The most common particle was PE (19.3–21.6%). Furthermore, the environmental risk assessment demonstrated that the PS polymer posed a Level-III risk in the water samples and a Level-II risk in the sediment samples from the Shiwuli River. The remaining polymer types exhibited Level-I risk. The PLIzone value for water was 2.24 during the flood season, indicating heavy pollution, and 1.66 during the non-flood season, indicating moderate pollution. Similarly, the PLIzone value for sediments was 2.34 during the flood season and 1.91 during the non-flood season, both suggesting a heavy pollution. These findings highlight the potential risk posed by MP pollution in the Shiwuli River to the quality of drinking water sources in Chaohu Lake in Hefei. They provide valuable insights into management, pollution control, and integrated management strategies pertaining to MPs in urban inland rivers in Hefei.
Open AccessSpatial–Temporal Distribution and Ecological Risk Assessment of Microplastics in the Shiwuli River
This study aimed to investigate the distribution of microplastics (MPs) within the Shiwuli River in Hefei, a Chinese inland city. Water and sediment samples were collected during flood season (from May to September) and non-flood season (from October to April) at 10 representative points along the truck stream. The electron microscope, the laser direct infrared chemical imaging system (LDIR), and the scanning electron microscope (SEM) were used to observe and quantify the colour and shape of the MPs, to identify the number, size, and polymer composition of the MPs, and to observe the microstructures of typical MP particles, respectively. The polymer risk index (RI) model and the pollution load index (PLI) model were used to assess the polymer-related risks and the overall extent of MP pollution in the river, respectively. Analysis of MP abundance for different sampling points showed that the water of Shiwuli River had an average abundance of MPs of 8.4 ± 2.5 particles/L during the flood season and 5.8 ± 1.7 particles/L during the non-flood season; the sediment had an average abundance of MPs of 78.9 ± 8.3 particles/kg during the flood season and 63.9 ± 7.1 particles/kg during the non-flood season. The abundance of MPs of different points was investigated. Result show that the more abundances of MPs were found at confluences with tributaries (S4, S5, and S6), where they are also close to the residential and industrial development, while lower values were found in agricultural areas (S8) and wetland ecological regions (S9 and S10). In water, the maximum appeared at S5 with 21.7 ± 4.6 particles/L during the flood season and 15.9 ± 4.2 particles/L during the non-flood season, respectively; the minimum appeared at S9 with 1.8 ± 1.0 particles/L during the flood season and 2.2 ± 0.4 particles/L during the non-flood season, respectively. In sediment, the maximum appeared at S5 with 174.1 ± 10.1 particles/kg during the flood season and 143.6 ± 10.4 particles/kg during the non-flood season, respectively; the minimum appeared at S8 with 10.3 ± 2.8 particles/kg during the flood season and at S9 with 12.1 ± 3.2 particles/kg during the non-flood season, respectively. MP characteristics were also studied. Results show that the MPs mainly exhibited a fibroid morphology (27.90–34%), and red-coloured particles (19.10%) within the smaller size less than 500 μm (38.60%) were more prevalent. Additionally, the result of LDIR scanning shows that a total of eleven types of MP polymers were found in the river water and sediment, including acrylates (ACR), chlorinated polyethylene (CPE), ethylene vinyl acetate (EVA), polyethylene (PE), polyethylene terephthalate (PET), polypropylene (PP), polystyrene (PS), polyurethane (PU), polyvinylchloride (PVC), polyamide (PA), and silicon. The most common particle was PE (19.3–21.6%). Furthermore, the environmental risk assessment demonstrated that the PS polymer posed a Level-III risk in the water samples and a Level-II risk in the sediment samples from the Shiwuli River. The remaining polymer types exhibited Level-I risk. The PLIzone value for water was 2.24 during the flood season, indicating heavy pollution, and 1.66 during the non-flood season, indicating moderate pollution. Similarly, the PLIzone value for sediments was 2.34 during the flood season and 1.91 during the non-flood season, both suggesting a heavy pollution. These findings highlight the potential risk posed by MP pollution in the Shiwuli River to the quality of drinking water sources in Chaohu Lake in Hefei. They provide valuable insights into management, pollution control, and integrated management strategies pertaining to MPs in urban inland rivers in Hefei.
- Open Access
Occurrence Characterization and Contamination Risk Evaluation of Microplastics in Hefei’s Urban Wastewater Treatment Plant
As one of the primary nodes in the flow of micro-plastics (MPs) in the environment, it is critical to examine and assess the Sewage Treatment, occurrence, and removal of MPs in waste treatment plant (WWTP). This research explored the shape, size, and composition of MPs at various stages of the WWTP process in the south of the city of Hefei, China, in dry and rainy weather conditions, as well as the removal effectiveness of MPs in a three-stage process. The collected MPs were quantitatively and qualitatively examined using an Osmosis electron microscope and micro-FTIR. The pollution risk of MPs in WWTP was assessed using the EU classification, labelling and packaging (CLP) standard and the pollution load index (PLI). The findings revealed that the average abundance of fibrous MPs was greatest in WWTP sewage and sludge, 49.3% and 39.7% in dry weather, and 50.1% and 43.2% in rainy weather, respectively. The average distribution of MPs in the 0–500 μm range was highest in WWTP wastewater and sludge, 64.9% and 60.4% in dry weather and 67.9% and 69.0% in rainy weather, respectively. Finally, the overall removal rate was 87.7% and 83.5%. At the same time, it has been demonstrated that MPs with varied compositions are strongly tied to human activities, and environmental conditions (such as rainy weather) also influence their source. In both dry and wet weather, the amount of polymers and the risk score were linked to the pollution risk of MPs in WWTP. In wet weather, the MPS pollution index was more variable. The pollution indices of MPs in row water and tail water were 2.40 and 2.46, respectively, which were heavily contaminated, and 1.0 and 1.2, which were moderately polluted. MPs in dewatered sludge had severely polluted indexes of 3.5 and 3.4, respectively. As a result, there is still MPs efflux or buildup in sludge during and after the WWTP process, which presents an ecological contamination concern.
Open AccessOccurrence Characterization and Contamination Risk Evaluation of Microplastics in Hefei’s Urban Wastewater Treatment Plant
As one of the primary nodes in the flow of micro-plastics (MPs) in the environment, it is critical to examine and assess the Sewage Treatment, occurrence, and removal of MPs in waste treatment plant (WWTP). This research explored the shape, size, and composition of MPs at various stages of the WWTP process in the south of the city of Hefei, China, in dry and rainy weather conditions, as well as the removal effectiveness of MPs in a three-stage process. The collected MPs were quantitatively and qualitatively examined using an Osmosis electron microscope and micro-FTIR. The pollution risk of MPs in WWTP was assessed using the EU classification, labelling and packaging (CLP) standard and the pollution load index (PLI). The findings revealed that the average abundance of fibrous MPs was greatest in WWTP sewage and sludge, 49.3% and 39.7% in dry weather, and 50.1% and 43.2% in rainy weather, respectively. The average distribution of MPs in the 0–500 μm range was highest in WWTP wastewater and sludge, 64.9% and 60.4% in dry weather and 67.9% and 69.0% in rainy weather, respectively. Finally, the overall removal rate was 87.7% and 83.5%. At the same time, it has been demonstrated that MPs with varied compositions are strongly tied to human activities, and environmental conditions (such as rainy weather) also influence their source. In both dry and wet weather, the amount of polymers and the risk score were linked to the pollution risk of MPs in WWTP. In wet weather, the MPS pollution index was more variable. The pollution indices of MPs in row water and tail water were 2.40 and 2.46, respectively, which were heavily contaminated, and 1.0 and 1.2, which were moderately polluted. MPs in dewatered sludge had severely polluted indexes of 3.5 and 3.4, respectively. As a result, there is still MPs efflux or buildup in sludge during and after the WWTP process, which presents an ecological contamination concern.
- Open Access
Recycling Lithium from Waste Lithium Bromide to Produce Lithium Hydroxide
Lithium resources face risks of shortages owing to the rapid development of the lithium industry. This makes the efficient production and recycling of lithium an issue that should be addressed immediately. Lithium bromide is widely used as a water-absorbent material, a humidity regulator, and an absorption refrigerant in the industry. However, there are few studies on the recovery of lithium from lithium bromide after disposal. In this paper, a bipolar membrane electrodialysis (BMED) process is proposed to convert waste lithium bromide into lithium hydroxide, with the generation of valuable hydrobromic acid as a by-product. The effects of the current density, the feed salt concentration, and the initial salt chamber volume on the performance of the BMED process were studied. When the reaction conditions were optimized, it was concluded that an initial salt chamber volume of 200 mL and a salt concentration of 0.3 mol/L provided the maximum benefit. A high current density leads to high energy consumption but with high current efficiency; therefore, the optimum current density was identified as 30 mA/cm2. Under the optimized conditions, the total economic cost of the BMED process was calculated as 2.243 USD·kg−1LiOH. As well as solving the problem of recycling waste lithium bromide, the process also represents a novel production methodology for lithium hydroxide. Given the prices of lithium hydroxide and hydrobromic acid, the process is both environmentally friendly and economical.
Open AccessRecycling Lithium from Waste Lithium Bromide to Produce Lithium Hydroxide
Lithium resources face risks of shortages owing to the rapid development of the lithium industry. This makes the efficient production and recycling of lithium an issue that should be addressed immediately. Lithium bromide is widely used as a water-absorbent material, a humidity regulator, and an absorption refrigerant in the industry. However, there are few studies on the recovery of lithium from lithium bromide after disposal. In this paper, a bipolar membrane electrodialysis (BMED) process is proposed to convert waste lithium bromide into lithium hydroxide, with the generation of valuable hydrobromic acid as a by-product. The effects of the current density, the feed salt concentration, and the initial salt chamber volume on the performance of the BMED process were studied. When the reaction conditions were optimized, it was concluded that an initial salt chamber volume of 200 mL and a salt concentration of 0.3 mol/L provided the maximum benefit. A high current density leads to high energy consumption but with high current efficiency; therefore, the optimum current density was identified as 30 mA/cm2. Under the optimized conditions, the total economic cost of the BMED process was calculated as 2.243 USD·kg−1LiOH. As well as solving the problem of recycling waste lithium bromide, the process also represents a novel production methodology for lithium hydroxide. Given the prices of lithium hydroxide and hydrobromic acid, the process is both environmentally friendly and economical.
- Open Access
Recovery of Acid and Base from Sodium Sulfate Containing Lithium Carbonate Using Bipolar Membrane Electrodialysis
Lithium carbonate is an important chemical raw material that is widely used in many contexts. The preparation of lithium carbonate by acid roasting is limited due to the large amounts of low-value sodium sulfate waste salts that result. In this research, bipolar membrane electrodialysis (BMED) technology was developed to treat waste sodium sulfate containing lithium carbonate for conversion of low-value sodium sulfate into high-value sulfuric acid and sodium hydroxide. Both can be used as raw materials in upstream processes. In order to verify the feasibility of the method, the effects of the feed salt concentration, current density, flow rate, and volume ratio on the desalination performance were determined. The conversion rate of sodium sulfate was close to 100%. The energy consumption obtained under the best experimental conditions was 1.4 kWh·kg−1. The purity of the obtained sulfuric acid and sodium hydroxide products reached 98.32% and 98.23%, respectively. Calculated under the best process conditions, the total process cost of BMED was estimated to be USD 0.705 kg−1 Na2SO4, which is considered low and provides an indication of the potential economic and environmental benefits of using applying this technology.
Open AccessRecovery of Acid and Base from Sodium Sulfate Containing Lithium Carbonate Using Bipolar Membrane Electrodialysis
Lithium carbonate is an important chemical raw material that is widely used in many contexts. The preparation of lithium carbonate by acid roasting is limited due to the large amounts of low-value sodium sulfate waste salts that result. In this research, bipolar membrane electrodialysis (BMED) technology was developed to treat waste sodium sulfate containing lithium carbonate for conversion of low-value sodium sulfate into high-value sulfuric acid and sodium hydroxide. Both can be used as raw materials in upstream processes. In order to verify the feasibility of the method, the effects of the feed salt concentration, current density, flow rate, and volume ratio on the desalination performance were determined. The conversion rate of sodium sulfate was close to 100%. The energy consumption obtained under the best experimental conditions was 1.4 kWh·kg−1. The purity of the obtained sulfuric acid and sodium hydroxide products reached 98.32% and 98.23%, respectively. Calculated under the best process conditions, the total process cost of BMED was estimated to be USD 0.705 kg−1 Na2SO4, which is considered low and provides an indication of the potential economic and environmental benefits of using applying this technology.
- Open Access
- 1 March 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 774 (1)
Electroplating Wastewater Treatment Method and Development Trend Analysis
Electroplating wastewater is a highly hazardous industrial wastewater with complex composition. For the treatment of electroplating wastewater, the traditional treatment methods include chemical treatment and membrane treatment. According to the requirements of electroplating wastewater treatment and industrial wastewater treatment in recent years, traditional electroplating wastewater treatment technology is difficult to reach new emission standards. The “zero emission” technology of electroplating wastewater has gradually become a new goal of ecological civilization construction. This article starts discussion from this aspect.
- 1 March 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 774 (1)
Open AccessElectroplating Wastewater Treatment Method and Development Trend Analysis
Electroplating wastewater is a highly hazardous industrial wastewater with complex composition. For the treatment of electroplating wastewater, the traditional treatment methods include chemical treatment and membrane treatment. According to the requirements of electroplating wastewater treatment and industrial wastewater treatment in recent years, traditional electroplating wastewater treatment technology is difficult to reach new emission standards. The “zero emission” technology of electroplating wastewater has gradually become a new goal of ecological civilization construction. This article starts discussion from this aspect.
- Open Access
- 1 March 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 774 (1)
The Relationship of Different COD Concentration, Sediment Pollutant Content with Hydrodynamic in Black Bloom Water Based on Stepwise Regression Method
To analyze the relationship of different COD concentration, sediment pollutants with hydrodynamic. Taking a polluted river as the research object, the data of flow velocity, water temperature, COD concentration, sediment OM content, sediment TN content and sediment TP content at nine sampling points were analyzed by stepwise regression and SPSS 25 data analysis software. Construct linear regression model of COD concentration Y, river flow velocity X1, water temperature X2, sediment OM content X3, sediment TN content X4, sediment TP content X5. The regression equation Y=106.172-64.304X4+ 0.065X5with correlation coefficient R=0.954 and determination coefficient R2=0.91 was obtained by stepwise regression method. The results showed that the concentration of COD in water was correlated with the content of nitrogen and phosphorus in river sediments, and negatively correlated with the content of TN and positively correlated with the content of TP. The model can be used to estimate COD load of water body by analyzing the nitrogen and phosphorus content in river sediments.
- 1 March 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 774 (1)
Open AccessThe Relationship of Different COD Concentration, Sediment Pollutant Content with Hydrodynamic in Black Bloom Water Based on Stepwise Regression Method
To analyze the relationship of different COD concentration, sediment pollutants with hydrodynamic. Taking a polluted river as the research object, the data of flow velocity, water temperature, COD concentration, sediment OM content, sediment TN content and sediment TP content at nine sampling points were analyzed by stepwise regression and SPSS 25 data analysis software. Construct linear regression model of COD concentration Y, river flow velocity X1, water temperature X2, sediment OM content X3, sediment TN content X4, sediment TP content X5. The regression equation Y=106.172-64.304X4+ 0.065X5with correlation coefficient R=0.954 and determination coefficient R2=0.91 was obtained by stepwise regression method. The results showed that the concentration of COD in water was correlated with the content of nitrogen and phosphorus in river sediments, and negatively correlated with the content of TN and positively correlated with the content of TP. The model can be used to estimate COD load of water body by analyzing the nitrogen and phosphorus content in river sediments.
- Open Access
Purification of Methylsulfonylmethane from Mixtures Containing Salt by Conventional Electrodialysis
Methylsulfonylmethane (MSM) is one of the main sources of sulfur for living bodies, but it is hard to obtain as a pure compound. Conventional electrodialysis (CED) is a mature technology that can be used for the separation and purification of biochemical products. In this study, the purification of MSM from mixtures containing salt was performed by CED. The effects of operating conditions such as operation voltage drop, feed MSM concentration, and electrolyte salt concentration on the separation performances were investigated. The results showed that the current efficiency reached 74.0%, and the energy consumption could be 12.3 Wh·L−1. As for the recovery rate and desalination rate, the highest recovery rate could be 97.4%, and the desalination rate was 98.5%. Based on process energy consumption calculation, the total cost of the whole process was estimated at only 2.34 $·t−1. Thus, CED is highly efficient and cost-effective for the separation and purification of MSM.
Open AccessPurification of Methylsulfonylmethane from Mixtures Containing Salt by Conventional Electrodialysis
Methylsulfonylmethane (MSM) is one of the main sources of sulfur for living bodies, but it is hard to obtain as a pure compound. Conventional electrodialysis (CED) is a mature technology that can be used for the separation and purification of biochemical products. In this study, the purification of MSM from mixtures containing salt was performed by CED. The effects of operating conditions such as operation voltage drop, feed MSM concentration, and electrolyte salt concentration on the separation performances were investigated. The results showed that the current efficiency reached 74.0%, and the energy consumption could be 12.3 Wh·L−1. As for the recovery rate and desalination rate, the highest recovery rate could be 97.4%, and the desalination rate was 98.5%. Based on process energy consumption calculation, the total cost of the whole process was estimated at only 2.34 $·t−1. Thus, CED is highly efficient and cost-effective for the separation and purification of MSM.
- 1 December 2009
- Vol. 25 (12) , 1871-81
[Progress in study on microbial enzymes for the metabolism of environmental refractory organic compounds].
With the rapid development of socialization and industrialization, more and more pollutes were produced and discharged into natural environment. It is harmful to human health and life. These pollutes included refractory degradation organic compounds like PAHs, RDX, HMX, CL-20, PCBs and alkanes and their relative substances. Various compounds exist in nature with long life span. They are the most hazardous than other organics. The impact of pollutes can be treated by microorganisms. Results showed that it is an effective way for bioremediation of these pollutes with microbial metabolism or cometabolism. A few key enzymes, mainly oxidative and reductive enzymes, connected with the first step of initial degradation. Normally, enzymes grouped with other active fraction on the cell membrane are composed of one oxidative and reductive system for substrates oxidation. The metabolic intermediates can be used with TCA by microorganisms. The pathways of metabolism and the key enzymes were summarized. The further research topics should be focused on microorganism screen and its relative enzyme, pathway and mechanism of metabolism or cometabolism for such compounds degradation, and the result was hoped for the environmental protection.
- 1 December 2009
- Vol. 25 (12) , 1871-81
[Progress in study on microbial enzymes for the metabolism of environmental refractory organic compounds].
With the rapid development of socialization and industrialization, more and more pollutes were produced and discharged into natural environment. It is harmful to human health and life. These pollutes included refractory degradation organic compounds like PAHs, RDX, HMX, CL-20, PCBs and alkanes and their relative substances. Various compounds exist in nature with long life span. They are the most hazardous than other organics. The impact of pollutes can be treated by microorganisms. Results showed that it is an effective way for bioremediation of these pollutes with microbial metabolism or cometabolism. A few key enzymes, mainly oxidative and reductive enzymes, connected with the first step of initial degradation. Normally, enzymes grouped with other active fraction on the cell membrane are composed of one oxidative and reductive system for substrates oxidation. The metabolic intermediates can be used with TCA by microorganisms. The pathways of metabolism and the key enzymes were summarized. The further research topics should be focused on microorganism screen and its relative enzyme, pathway and mechanism of metabolism or cometabolism for such compounds degradation, and the result was hoped for the environmental protection.