Jie Jin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jie Jin has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Ke Wu
School of Biology, Food and Environment, Hefei University, Hefei 230601, China
2 shared publications - Ahmad Hosseinzadeh
Centre for Green Technology, School of Civil and Environmental Engineering, University of Technology Sydney, NSW 2007, Australia
1 shared publication - Bin Liu
School of Biology, Food and Environment, Hefei University, Hefei 230601, China
1 shared publication - Bing-Jie Ni
School of Civil and Environmental Engineering, The University of New South Wales, Sydney, Australia
1 shared publication Hoang Nhat Phong Vo
Centre for Technology in Water and Wastewater, School of Civil and Environmental Engineering, University of Technology Sydney, Sydney, NSW, 2007, Australia
1 shared publicationJing Song Ye
School of Biology, Food and Environment Engineering, Hefei University, China
1 shared publication
Latest Publications
- Open Access
Spatial–Temporal Distribution and Ecological Risk Assessment of Microplastics in the Shiwuli River
This study aimed to investigate the distribution of microplastics (MPs) within the Shiwuli River in Hefei, a Chinese inland city. Water and sediment samples were collected during flood season (from May to September) and non-flood season (from October to April) at 10 representative points along the truck stream. The electron microscope, the laser direct infrared chemical imaging system (LDIR), and the scanning electron microscope (SEM) were used to observe and quantify the colour and shape of the MPs, to identify the number, size, and polymer composition of the MPs, and to observe the microstructures of typical MP particles, respectively. The polymer risk index (RI) model and the pollution load index (PLI) model were used to assess the polymer-related risks and the overall extent of MP pollution in the river, respectively. Analysis of MP abundance for different sampling points showed that the water of Shiwuli River had an average abundance of MPs of 8.4 ± 2.5 particles/L during the flood season and 5.8 ± 1.7 particles/L during the non-flood season; the sediment had an average abundance of MPs of 78.9 ± 8.3 particles/kg during the flood season and 63.9 ± 7.1 particles/kg during the non-flood season. The abundance of MPs of different points was investigated. Result show that the more abundances of MPs were found at confluences with tributaries (S4, S5, and S6), where they are also close to the residential and industrial development, while lower values were found in agricultural areas (S8) and wetland ecological regions (S9 and S10). In water, the maximum appeared at S5 with 21.7 ± 4.6 particles/L during the flood season and 15.9 ± 4.2 particles/L during the non-flood season, respectively; the minimum appeared at S9 with 1.8 ± 1.0 particles/L during the flood season and 2.2 ± 0.4 particles/L during the non-flood season, respectively. In sediment, the maximum appeared at S5 with 174.1 ± 10.1 particles/kg during the flood season and 143.6 ± 10.4 particles/kg during the non-flood season, respectively; the minimum appeared at S8 with 10.3 ± 2.8 particles/kg during the flood season and at S9 with 12.1 ± 3.2 particles/kg during the non-flood season, respectively. MP characteristics were also studied. Results show that the MPs mainly exhibited a fibroid morphology (27.90–34%), and red-coloured particles (19.10%) within the smaller size less than 500 μm (38.60%) were more prevalent. Additionally, the result of LDIR scanning shows that a total of eleven types of MP polymers were found in the river water and sediment, including acrylates (ACR), chlorinated polyethylene (CPE), ethylene vinyl acetate (EVA), polyethylene (PE), polyethylene terephthalate (PET), polypropylene (PP), polystyrene (PS), polyurethane (PU), polyvinylchloride (PVC), polyamide (PA), and silicon. The most common particle was PE (19.3–21.6%). Furthermore, the environmental risk assessment demonstrated that the PS polymer posed a Level-III risk in the water samples and a Level-II risk in the sediment samples from the Shiwuli River. The remaining polymer types exhibited Level-I risk. The PLIzone value for water was 2.24 during the flood season, indicating heavy pollution, and 1.66 during the non-flood season, indicating moderate pollution. Similarly, the PLIzone value for sediments was 2.34 during the flood season and 1.91 during the non-flood season, both suggesting a heavy pollution. These findings highlight the potential risk posed by MP pollution in the Shiwuli River to the quality of drinking water sources in Chaohu Lake in Hefei. They provide valuable insights into management, pollution control, and integrated management strategies pertaining to MPs in urban inland rivers in Hefei.
Open AccessSpatial–Temporal Distribution and Ecological Risk Assessment of Microplastics in the Shiwuli River
This study aimed to investigate the distribution of microplastics (MPs) within the Shiwuli River in Hefei, a Chinese inland city. Water and sediment samples were collected during flood season (from May to September) and non-flood season (from October to April) at 10 representative points along the truck stream. The electron microscope, the laser direct infrared chemical imaging system (LDIR), and the scanning electron microscope (SEM) were used to observe and quantify the colour and shape of the MPs, to identify the number, size, and polymer composition of the MPs, and to observe the microstructures of typical MP particles, respectively. The polymer risk index (RI) model and the pollution load index (PLI) model were used to assess the polymer-related risks and the overall extent of MP pollution in the river, respectively. Analysis of MP abundance for different sampling points showed that the water of Shiwuli River had an average abundance of MPs of 8.4 ± 2.5 particles/L during the flood season and 5.8 ± 1.7 particles/L during the non-flood season; the sediment had an average abundance of MPs of 78.9 ± 8.3 particles/kg during the flood season and 63.9 ± 7.1 particles/kg during the non-flood season. The abundance of MPs of different points was investigated. Result show that the more abundances of MPs were found at confluences with tributaries (S4, S5, and S6), where they are also close to the residential and industrial development, while lower values were found in agricultural areas (S8) and wetland ecological regions (S9 and S10). In water, the maximum appeared at S5 with 21.7 ± 4.6 particles/L during the flood season and 15.9 ± 4.2 particles/L during the non-flood season, respectively; the minimum appeared at S9 with 1.8 ± 1.0 particles/L during the flood season and 2.2 ± 0.4 particles/L during the non-flood season, respectively. In sediment, the maximum appeared at S5 with 174.1 ± 10.1 particles/kg during the flood season and 143.6 ± 10.4 particles/kg during the non-flood season, respectively; the minimum appeared at S8 with 10.3 ± 2.8 particles/kg during the flood season and at S9 with 12.1 ± 3.2 particles/kg during the non-flood season, respectively. MP characteristics were also studied. Results show that the MPs mainly exhibited a fibroid morphology (27.90–34%), and red-coloured particles (19.10%) within the smaller size less than 500 μm (38.60%) were more prevalent. Additionally, the result of LDIR scanning shows that a total of eleven types of MP polymers were found in the river water and sediment, including acrylates (ACR), chlorinated polyethylene (CPE), ethylene vinyl acetate (EVA), polyethylene (PE), polyethylene terephthalate (PET), polypropylene (PP), polystyrene (PS), polyurethane (PU), polyvinylchloride (PVC), polyamide (PA), and silicon. The most common particle was PE (19.3–21.6%). Furthermore, the environmental risk assessment demonstrated that the PS polymer posed a Level-III risk in the water samples and a Level-II risk in the sediment samples from the Shiwuli River. The remaining polymer types exhibited Level-I risk. The PLIzone value for water was 2.24 during the flood season, indicating heavy pollution, and 1.66 during the non-flood season, indicating moderate pollution. Similarly, the PLIzone value for sediments was 2.34 during the flood season and 1.91 during the non-flood season, both suggesting a heavy pollution. These findings highlight the potential risk posed by MP pollution in the Shiwuli River to the quality of drinking water sources in Chaohu Lake in Hefei. They provide valuable insights into management, pollution control, and integrated management strategies pertaining to MPs in urban inland rivers in Hefei.
- Open Access
Recycling Lithium from Waste Lithium Bromide to Produce Lithium Hydroxide
Lithium resources face risks of shortages owing to the rapid development of the lithium industry. This makes the efficient production and recycling of lithium an issue that should be addressed immediately. Lithium bromide is widely used as a water-absorbent material, a humidity regulator, and an absorption refrigerant in the industry. However, there are few studies on the recovery of lithium from lithium bromide after disposal. In this paper, a bipolar membrane electrodialysis (BMED) process is proposed to convert waste lithium bromide into lithium hydroxide, with the generation of valuable hydrobromic acid as a by-product. The effects of the current density, the feed salt concentration, and the initial salt chamber volume on the performance of the BMED process were studied. When the reaction conditions were optimized, it was concluded that an initial salt chamber volume of 200 mL and a salt concentration of 0.3 mol/L provided the maximum benefit. A high current density leads to high energy consumption but with high current efficiency; therefore, the optimum current density was identified as 30 mA/cm2. Under the optimized conditions, the total economic cost of the BMED process was calculated as 2.243 USD·kg−1LiOH. As well as solving the problem of recycling waste lithium bromide, the process also represents a novel production methodology for lithium hydroxide. Given the prices of lithium hydroxide and hydrobromic acid, the process is both environmentally friendly and economical.
Open AccessRecycling Lithium from Waste Lithium Bromide to Produce Lithium Hydroxide
Lithium resources face risks of shortages owing to the rapid development of the lithium industry. This makes the efficient production and recycling of lithium an issue that should be addressed immediately. Lithium bromide is widely used as a water-absorbent material, a humidity regulator, and an absorption refrigerant in the industry. However, there are few studies on the recovery of lithium from lithium bromide after disposal. In this paper, a bipolar membrane electrodialysis (BMED) process is proposed to convert waste lithium bromide into lithium hydroxide, with the generation of valuable hydrobromic acid as a by-product. The effects of the current density, the feed salt concentration, and the initial salt chamber volume on the performance of the BMED process were studied. When the reaction conditions were optimized, it was concluded that an initial salt chamber volume of 200 mL and a salt concentration of 0.3 mol/L provided the maximum benefit. A high current density leads to high energy consumption but with high current efficiency; therefore, the optimum current density was identified as 30 mA/cm2. Under the optimized conditions, the total economic cost of the BMED process was calculated as 2.243 USD·kg−1LiOH. As well as solving the problem of recycling waste lithium bromide, the process also represents a novel production methodology for lithium hydroxide. Given the prices of lithium hydroxide and hydrobromic acid, the process is both environmentally friendly and economical.