JLJean-Pierre Leclerc

Jean-Pierre Leclerc

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jean-Pierre Leclerc has a total of 22 co-authors. Here are the top co-authors by number of shared publications:

  • Adel Aitbara

    Laboratoire de traitement des eaux et valorisation des déchets industriels, Faculté des Sciences, Département de chimie, Bp12, Annaba 23000, Algérie, Tel. +213 550094053, Tel. +213 555527386, Tel. +213 663243605

    1 shared publication
  • Anis Attour

    College of Engineering , Imam Mohammad Ibn Saud Islamic University (IMSIU) , Riyadh 11432 , Saudi Arabia , imamu.edu.sa

    1 shared publication
  • F. Berrekhis

    Equipe de Physico-chimie des Matériaux, Ecole Normale Supérieure, Université Cadi Ayyad, BP 2400, 40000 Marrakech, Morocco

    1 shared publication
  • F. Lapicque

    Laboratoire Réactions et Génie des Procédés (LRGP) UMR 7274, CNRS, Université de Lorraine, 1 rue Grandville, BP 20451, 54001 Nancy cedex, France

    1 shared publication
  • François Lapicque

    Laboratoire Réaction et Génie des Procédés (LRGP), CNRS – Université de Lorraine, ENSIC, 1 rue Grandville B.P. 20451, Nancy Cedex 54000, France, Tel. +33 3 83175066

    1 shared publication
  • François Lapicque

    Laboratoire Réactions et Génie des procédés, CNRS, UMR 7274, F-54001 Nancy Cedex, France, Tel. +33 3 83 17 52 66, Tel. +33 3 83 17 50 66

    1 shared publication

Latest Publications

  • Treatment of highly concentrated tannery wastewater using electrocoagulation: Influence of the quality of aluminium used for the electrode

    by S. Elabbas, N. Ouazzani, L. Mandi, F. Berrekhis, M. Perdicakis, S. Pontvianne, M-N. Pons, F. Lapicque, J-P Leclerc


  • Open Access

    Electrokinetic removal of aluminum and chromium from industrial wastewater electrocoagulation treatment sludge

    by Mouna Cherifi, Sabir Hazourli, Steeve Pontvianne, François Lapicque, Jean-Pierre Leclerc

    Treatment of industrial wastewaters by electrocoagulation is very efficient to remove numerous types of pollutant (organic, mineral, colored, metal). However, few researches are devoted to the elimination of metals contained in the generated sludge. The objective of this paper was to study the possible simultaneous removal of aluminum (issued from the electrodes) and chromium (initially present in the effluent) contained in the sludge by electrochemical migration. Electrocoagulation treatment of textile industrial wastewater in which chromium has been added was carried out using aluminum electrodes. Turbidity, COD, and TOC could be efficiently removed with abatement yields, respectively, at 97, 93, and 90%. For chromium, only 62% of the initial amount was eliminated by applying the highest current with a long operating time. The generated sludge contained high amounts of Cr and Al (749 and 1,260 mg/kg of dry sludge), far above the maximum level allowed by legislation. The possibility of removing these pollutants from the resulting sludge using electrokinetic technique was investigated. Acetic acid at 1 or 3 M and citric acid at 3 and 6 M were used as catholyte solutions to enhance the removal of aluminum and chromium(III). Best results for aluminum removal were obtained using 3 M acetic acid: up to 82% of the initial Al was recovered in the cathode chamber, whereas citric acid was more effective in chromium removal: up to 79% was transported to the cathode chamber with 6 M citric acid. Specific energy consumption is also discussed.


  • Open Access

    Intensification of phosphate removal using electrocoagulation treatment by continuous pH adjustment and optimal electrode connection mode

    by Anis Attour, Neila Ben Grich, Mohamed Mouldi Tlili, Mohamed Ben Amor, François Lapicque, Jean-Pierre Leclerc

    This paper discusses two possible ways of intensifying the electrocoagulation treatment of water containing phosphate. The first one consists of controlling the chemical composition of the water by continuous adjustment of the pH. The second aspect focuses on electrode connection modes, and the four different modes were tested monopolar in series, in parallels and independents, and finally bipolar. Experiments were conducted in a small batch reactor containing water with 100 mg P/L using electrodes of aluminum. Several electrical connections were used for the water treatment under favorable operating conditions determined by a study and presented in a previous paper. The influence of pH adjustment was conducted using different adjustment step times (no adjustment, every 30, 10 and 5 min). The kinetics of the treatment was found to be accelerated by continuous adjustment of the pH. The choice of the electrode connection modes was found to strongly affect the efficiency of the treatment, the Faradic yield, and the consumption of energy. The monopolar in parallels connection mode was found to be the most economic, whereas bipolar in parallels was found to favor a higher kinetic rate of treatment.


  • Open Access

    Continuous treatment of industrial dairy effluent by electrocoagulation using aluminum electrodes

    by Adel Aitbara, Mouna Cherifi, Sabir Hazourli, Jean-Pierre Leclerc

    Electrocoagulation is one of the most efficient and convenient techniques for the elimination of several types of pollutants. Its efficiency has been validated for numerous industrial effluents (food, mechanical, textiles, paper industries, etc.). This paper deals with the treatment of dairy wastewater in Algeria by electrocoagulation using aluminum electrodes. The experiments were conducted in a small continuous reactor at laboratory scale. Turbidity and chemical oxygen demand (COD) were followed continuously during the startup period and at steady-state, where as BOD5 (five-day biological oxygen demand), greases, and phosphorus were analyzed punctually at steady state using the better operating conditions. The effect of operational parameters, such as current density, initial pH, inlet flow rate, and the temperature of waste water, were examined to optimize the effectiveness of the treatment. A satisfactory reduction of 98% of the turbidity and 90% of the COD were obtained for the optimal conditions. The abatements of BOD5 and greases were close to 97%, whereas 70% of the phosphorus was eliminated. Treatment of industrial wastewater concentrated with several milk powder concentrations has been also analyzed. Reasonable energy consumption of around 2 to 3.5 kWh/m3 for adequate operating conditions validates the economic reliability of this choice of treatment.