KKKyung Hwan Kim

Kyung Hwan Kim

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kyung Hwan Kim has a total of 79 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Post-Annealing Temperature Effects on Electrical Characteristics of Sputtered Mo/β-Ga2O3 Vertical Schottky Barrier Diodes

    by Hyungi Kang, Kyung Hwan Kim, Jeong Soo Hong

    In this study, Mo/β-Ga2O3 vertical Schottky barrier diodes (SBDs) were fabricated using a sputtering process, and the electrical characteristics were evaluated as a function of post-annealing temperature. β-Ga2O3 is an ultra-wide bandgap semiconductor (UWBG) with a bandgap of about 4.8 eV and a critical breakdown field of 8 MV/cm, a promising material for high-voltage power switching applications. Mo (molybdenum) has a higher work function (~4.95 eV) than the electron affinity (~4.0 eV) of β-Ga2O3, its melting point (2623 °C) is higher than Pt (1768 °C) and Ni (1455 °C), so it has excellent thermal stability, and it is selected as a Schottky metal. The device is a structure in which a Si-doped β-Ga2O3 epitaxial layer (10 μm, Nd-Na = 2.2 × 1016 cm−3) is grown on an Sn-doped β-Ga2O3 substrate (415 μm, Nd-Na = 4.5 × 1018 cm−3). The Ti/Au (10/40 nm) was used for the back ohmic junction and Mo (300 nm) was used for the front Schottky junction. Post-annealing treatment was performed at 400, 500, and 550 °C using a rapid thermal annealing process (RTA) in an Ar gas atmosphere, and in this process, the Schottky junction and ohmic junction were formed simultaneously. Electrical characteristics including current-voltage (I–V), capacitance-voltage (C–V), Schottky barrier height (SBH), ideality factor (n), turn-on voltage (Von), on-resistance (Ron), on/off ratio, and breakdown voltage (BV) were evaluated. No obvious Schottky characteristics were observed before post-annealing treatment, which means that As-deposited Mo does not form a rectifying junction on the β-Ga2O3 without post-annealing treatment. After post-annealing treatment, the I–V curve of the Schottky rectification characteristics could be confirmed under all three conditions. Among the three conditions, the device annealed at 500 °C exhibits best performance, with an SBH of 0.96 eV, n of 1.01, Von of 0.72 V, Ron of 13.8 mΩ·cm2, an on/off ratio of 109, a breakdown voltage of −474 V, and a PFOM of 16.3 MW/cm2. As a result of temperature-dependent I–V measurement, as chuck temperature increased, the reverse leakage current increased and SBH decreased in all devices, which is consistent with the thermally activated carrier transport. These results demonstrate that the Mo/β-Ga2O3 SBDs are a thermally stable contact for power device applications.

  • Open Access

    Post Annealing Temperature Effects on Electrical Characteristics of Sputtered Mo/β-Ga₂O₃ Vertical Schottky Barrier Diodes

    by Hyungi Kang, Kyung Hwan Kim, Jeong Soo Hong

    In this study, Mo/β-Ga₂O₃ vertical Schottky barrier diodes (SBDs) were fabricated using a sputtering process, and the electrical characteristics were evaluated as a function of post-annealing temperature. β-Ga₂O₃ is an ultra-wide bandgap semiconductor (UWBG) with a bandgap of about 4.8 eV and a critical breakdown field of 8 MV/cm, a promising material for high-voltage power switching applications. Mo (molybdenum) has a higher work function (~4.95 eV) than the electron affinity (~4.0 eV) of β-Ga₂O₃, its melting point (2623°C) is higher than Pt (1768°C) and Ni (1455°C), so it has excellent thermal stability, and it is selected as Schottky metal. The device is a structure in which a Si-doped β-Ga₂O ₃ epitaxial layer (10μm, Nd–Na = 2.2 × 1016cm ⁻³) is grown on an Sn-doped β-Ga₂O ₃ substrate (415μm, Nd–Na = 4.5 × 10¹⁸ cm ⁻³). The Ti/Au (10/40 nm) was used for back ohmic junction and Mo (300 nm) was used for front Schottky junction. Post-annealing treatment was performed at 400, 500, and 550°C using a rapid-thermal annealing process (RTA) in an Ar gas atmosphere, and in this process, Schottky junction and ohmic junction were formed simultaneously. Electrical characteristics including current-voltage(I-V), capacitance-voltage(C-V), Schottky barrier height (SBH), ideality factor (n), turn-on voltage (Von), on-resistance (Ron), on/off ratio, and breakdown voltage (BV) were evaluated. No obvious Schottky characteristics were observed before post-annealing treatment, which means that As-deposited Mo does not form a rectifying junction on the β-Ga₂O₃ without post-annealing treatment. After post-annealing treatment, the I–V curve of the Schottky rectification characteristics could be confirmed under all three conditions. Among the three conditions, the device annealed at 500°C exhibits best performance, with SBH of 0.96 eV, n of 1.01, Von of 0.72 V, Ron of 13.8 mΩ·cm², an on/off ratio of 10⁹, a breakdown voltage of -474 V, and a PFOM of 16.3MW/cm2. As a result of temperature-dependent I–V measurement, as chuck temperature increased, the reverse leakage current increased and SBH decreased in all devices, which is consistent with the thermally activated carrier transport. These results demonstrate that the Mo/β-Ga₂O₃ SBDs are a thermally stable contact for power device applications.

  • Open Access

    Effect of Oxygen-Evaporation-Preventative Post-Annealing Gas Conditions on NiO Thin Films

    by Hyungmin Kim, Kyunghwan Kim, Jeongsoo Hong

    In this study, NiO films were fabricated through radio frequency sputtering with various oxygen flow rates and processed via rapid thermal annealing under Ar, O2, and N2 atmospheres. The electrical, optical, and crystallographic properties of the NiO films were influenced by their oxygen content in each film. As the oxygen content, carrier concentration, and resistivity increased, transmittance and mobility decreased. The carrier mobility of the NiO film in the p-type layer of the photodetector requires improvement. Rapid thermal annealing (RTA) has been widely used to improve the crystallinity and mobility of films. However, the reduction in oxygen content during RTA causes a decrease in the carrier concentration and transmittance of NiO films. Regarding the aim of preventing a reduction in oxygen content in the NiO films due to the RTA process, an O2 atmosphere (compared with Ar and N2 atmospheres) was identified as the optimal condition for mobility (3.42 cm2/V·s) and transmittance (50%).


  • Open Access

    Effect of the Working Pressure and Oxygen Gas Flow Rate on the Fabrication of Single-Phase Ag2O Thin Films

    by Jiyoon Choi, Jiha Seong, Sangbin Park, Hyungmin Kim, Sangmo Kim, Kyung Hwan Kim, Jeongsoo Hong

    Ag2O thin films have been applied in various devices, such as photodetectors, photocatalysts, and gas sensors, because of their excellent thermal stability, strong electrical properties, and stable structures. However, because various phases of silver oxide exist, the fabrication of single-phase Ag2O thin films using a general deposition system is difficult. In this study, Ag2O thin films were deposited on glass substrates at different working pressures and O2 gas flow rates using a facing-target sputtering (FTS) system. After optimizing the working pressure and O2 gas flow rate, the Ag2O thin films were post-annealed at different temperatures ranging from 100 to 400 °C to improve their crystallographic properties. The X-ray diffraction patterns of the as-fabricated Ag2O thin films indicated the presence of a single phase of Ag2O, and the ultraviolet–visible (UV–vis) spectral analysis indicated transmittance of 65% in the visible light region. The optimum working pressure and O2 gas flow rate were determined to be 4 mTorr and 3.4 sccm, respectively. Finally, the effect of the post-annealing temperature on the thin film was investigated; the Ag2O peak had high intensity at 300 °C, suggesting this as the optimum post-annealing temperature.


  • Open Access

    Enhanced Responsivity and Optoelectronic Properties of Self-Powered Solar-Blind Ag2O/β-Ga2O3 Heterojunction-Based Photodetector with Ag:AZO Co-Sputtered Electrode

    by Younghwa Yoon, Sangbin Park, Taejun Park, Hyungmin Kim, Kyunghwan Kim, Jeongsoo Hong

    A Ag:AZO electrode was used as an electrode for a self-powered solar-blind ultraviolet photodetector based on a Ag2O/β-Ga2O3 heterojunction. The Ag:AZO electrode was fabricated by co-sputtering Ag and AZO heterogeneous targets using the structural characteristics of a Facing Targets Sputtering (FTS) system with two-facing targets, and the electrical, crystallographic, structural, and optical properties of the fabricated thin film were evaluated. A photodetector was fabricated and evaluated based on the research results that the surface roughness of the electrode can reduce the light energy loss by reducing the scattering and reflectance of incident light energy and improving the trapping phenomenon between interfaces. The thickness of the electrodes was varied from 20 nm to 50 nm depending on the sputtering time. The optoelectronic properties were measured under 254 nm UV-C light, the on/off ratio of the 20 nm Ag:AZO electrode with the lowest surface roughness was 2.01 × 108, and the responsivity and detectivity were 56 mA/W and 6.99 × 1011 Jones, respectively. The Ag2O/β-Ga2O3-based solar-blind photodetector with a newly fabricated top electrode exhibited improved response with self-powered characteristics.


  • Open Access

    A Self-Powered High-Responsivity, Fast-Response-Speed Solar-Blind Ultraviolet Photodetector Based on CuO/β-Ga2O3 Heterojunction with Built-In Potential Control

    by Sangbin Park, Younghwa Yoon, Hyungmin Kim, Taejun Park, Kyunghwan Kim, Jeongsoo Hong

    Controlling built-in potential can enhance the photoresponse performance of self-powered photodetectors. Among the methods for controlling the built-in potential of self-powered devices, postannealing is simpler, more efficient, and less expensive than ion doping and alternative material research. In this study, a CuO film was deposited on a β-Ga2O3 epitaxial layer via reactive sputtering with an FTS system, and a self-powered solar-blind photodetector was fabricated through a CuO/β-Ga2O3 heterojunction and postannealed at different temperatures. The postannealing process reduced the defects and dislocations at the interface between each layer and affected the electrical and structural properties of the CuO film. After postannealing at 300 °C, the carrier concentration of the CuO film increased from 4.24 × 1018 to 1.36 × 1020 cm−3, bringing the Fermi level toward the valence band of the CuO film and increasing the built-in potential of the CuO/β-Ga2O3 heterojunction. Thus, the photogenerated carriers were rapidly separated, increasing the sensitivity and response speed of the photodetector. The as-fabricated photodetector with 300 °C postannealing exhibited a photo-to-dark current ratio of 1.07 × 103; responsivity and detectivity of 30.3 mA/W and 1.10 × 1012 Jones, respectively; and fast rise and decay times of 12 ms and 14 ms, respectively. After three months of storage in an open-air space, the photocurrent density of the photodetector was maintained, indicating good stability with aging. These results suggest that the photocharacteristics of CuO/β-Ga2O3 heterojunction self-powered solar-blind photodetectors can be improved through built-in potential control using a postannealing process.


  • Open Access

    Temperature-Dependent Self-Powered Solar-Blind Photodetector Based on Ag2O/β-Ga2O3 Heterojunction

    by Taejun Park, Sangbin Park, Joon Hui Park, Ji Young Min, Yusup Jung, Sinsu Kyoung, Tai Young Kang, Kyunghwan Kim, You Seung Rim, Jeongsoo Hong

    In this study, a high-photoresponsivity self-powered deep ultraviolet (DUV) photodetector based on an Ag2O/β-Ga2O3 heterojunction was fabricated by depositing a p-type Ag2O thin film onto an n-type β-Ga2O3 layer. The device characteristics after post-annealing at temperatures ranging from 0 to 400 °C were investigated. Our DUV devices exhibited typical rectification characteristics. At a post-annealing temperature of 300 °C, the as-fabricated device had a low leakage current of 4.24 × 10−11 A, ideality factor of 2.08, and a barrier height of 1.12 eV. Moreover, a high photo-responsivity of 12.87 mA/W was obtained at a 100 μW/cm2 light intensity at a 254 nm wavelength at zero bias voltage, the detectivity was 2.70 × 1011 Jones, and the rise and fall time were 29.76, 46.73 ms, respectively. Based on these results, the Ag2O/β-Ga2O3 heterojunction photodetector operates without an externally applied voltage and has high responsivity, which will help in the performance improvement of ultraviolet sensing systems.


  • Open Access

    Reduced On-Resistance and Improved 4H-SiC Junction Barrier Schottky Diodes Performance by Laser Annealing on C-Face Ohmic Regions in Thin Structures

    by Kihyun Kim, Yehwan Kang, Seungbok Yun, Changheon Yang, Eunsik Jung, Jeongsoo Hong, Kyunghwan Kim

    In this study, we investigated the characteristics of the n-type Ni/SiC ohmic contact using the laser annealing process on thin wafers. The electrical behavior of the ohmic contacts was tested in 4H-SiC JBS diode devices. As a result, a wafer thickness of 100 μm in the 4H-SiC JBS diode achieved a forward voltage of 1.33 V at 20 A with a laser annealing process using Ni silicide. Using a laser annealing process on a wafer thickness of 100 μm, an on-resistance decrease of almost 22% was demonstrated. Based on our experimental results, we suggest an alternative laser annealing fabrication scheme to obtain low on-resistance SiC power devices with thin structures after SiC grinding.


  • Open Access

    Effect of Annealing in ITO Film Prepared at Various Argon-and-Oxygen-Mixture Ratios via Facing-Target Sputtering for Transparent Electrode of Perovskite Solar Cells

    by Yujin Kim, Sung Hwan Joo, Seong Gwan Shin, Hyung Wook Choi, Chung Wung Bark, You Seung Rim, Kyung Hwan Kim, Sangmo Kim

    Normal perovskite solar cells (PSCs) consist of the following layers: transparent electrode, electron-transport layer (ETL), light-absorbing perovskite layer, hole-transport layer (HTL), and metal electrode. Energy, such as electricity, is produced through light absorbance and electron–hole generation/transport between two electrode types (metal film and transparent conducting film). Among stacked layers in a PSC, the transparent electrode plays the high-performance-power-conversion-efficiency role. Transparent electrodes should have high-visible-range transparency and low resistance. Therefore, in this study, we prepared indium tin oxide (ITO) films on a glass substrate by using facing-target sputtering without substrate heating treatment and investigate the heating-treatment effect on the ITO-film properties for perovskite solar cells (PSCs). Moreover, we fabricated PSCs with ITO films prepared at various oxygen flows during the sputtering process, and their energy-conversion properties are investigated.


  • Open Access

    Effects of Drying Temperature and Molar Concentration on Structural, Optical, and Electrical Properties of β-Ga2O3 Thin Films Fabricated by Sol–Gel Method

    by Taejun Park, Kyunghwan Kim, Jeongsoo Hong

    In this study, β-Ga2O3 films were fabricated on a quartz substrate by the sol–gel method using different drying temperatures and solutions of different molar concentrations, and their structural, optical, and electrical properties were evaluated. The as-fabricated films exhibited a monoclinic β-Ga2O3 crystal structure, whose crystallinity and crystallite size increased with increasing molar concentration of the solutions used and increasing drying temperature. Scanning electron microscopy of the as-prepared samples revealed dense surface morphologies and that the thickness of the films also depended on the deposition conditions. The average transmittance of all the samples was above 8% in visible light, and the calculated optical bandgap energy was 4.9 eV. The resistivity measured using a 4-point probe system was 3.7 × 103 Ω cm.