Mark C. Hardy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mark C. Hardy has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
R. C. Buckingham
7 shared publicationsC. Argyrakis
Rolls-Royce plc
5 shared publicationsH. S. Kitaguchi
The University of Birmingham
3 shared publications- Howard James Stone
University of Cambridge
3 shared publications K. Severs
ATI Forged Products Cudahy, Cudahy, USA
3 shared publications- Mark Thomas Whitaker
Institute of Structural Materials, Swansea University, Fabian Way, Swansea SA1 8EN, UK
3 shared publications
Latest Publications
- 4 September 2026
- Published by Springer Nature
- p. 583-604
Influence of Al:Nb Ratio on Microstructure and Mechanical Properties in New Polycrystalline Ni Superalloys
- 4 September 2026
- Published by Springer Nature
- p. 583-604
Influence of Al:Nb Ratio on Microstructure and Mechanical Properties in New Polycrystalline Ni Superalloys
- Open Access
Predictions of Crack Growth Rates, R-Ratio and Overload Effects Based on Smooth Specimen LCF Data and the Moving Plastic Stress Field Ahead of the Crack Tip
The use of the stress intensity factor K to characterize the severity of crack tip stress fields is widespread throughout engineering. The relationship between K and the crack growth rate is then usually represented empirically by a straight line Paris law relationship on logarithmic axes. This study develops an analytical relationship between the two by linking crack growth to the accumulation of fatigue damage ahead of the moving crack tip. A stress-based fatigue model was used, with inputs from plastic 2D plane stress FE analyses representing an edge crack by a sharp semi-circular notch. Stress–distance profiles ahead of the crack tip were extracted at the maximum and minimum points of a range of fatigue loading cycles. These were then used with data from smooth specimen LCF tests to predict the build-up of fatigue damage at regularly spaced locations ahead of the crack tip and hence crack growth rates. Full da/dN–ΔK curves were generated for the nickel-based superalloy RR1000 at 20 °C with loading R-ratios of 0, −1 and 0.5. The R = 0 and R = −1 crack growth rate predictions agreed well with experimental data, as did the steeper growth rate slope calculated at R = 0.5. The method was then extended to predict overload behaviour.
Open AccessPredictions of Crack Growth Rates, R-Ratio and Overload Effects Based on Smooth Specimen LCF Data and the Moving Plastic Stress Field Ahead of the Crack Tip
The use of the stress intensity factor K to characterize the severity of crack tip stress fields is widespread throughout engineering. The relationship between K and the crack growth rate is then usually represented empirically by a straight line Paris law relationship on logarithmic axes. This study develops an analytical relationship between the two by linking crack growth to the accumulation of fatigue damage ahead of the moving crack tip. A stress-based fatigue model was used, with inputs from plastic 2D plane stress FE analyses representing an edge crack by a sharp semi-circular notch. Stress–distance profiles ahead of the crack tip were extracted at the maximum and minimum points of a range of fatigue loading cycles. These were then used with data from smooth specimen LCF tests to predict the build-up of fatigue damage at regularly spaced locations ahead of the crack tip and hence crack growth rates. Full da/dN–ΔK curves were generated for the nickel-based superalloy RR1000 at 20 °C with loading R-ratios of 0, −1 and 0.5. The R = 0 and R = −1 crack growth rate predictions agreed well with experimental data, as did the steeper growth rate slope calculated at R = 0.5. The method was then extended to predict overload behaviour.
- Open Access
- 21 April 2026
- Published by MDPI AG in Preprints.org
Predictions of Crack Growth Rates, R-Ratio and Overload Effects Based on Smooth Specimen LCF Data and the Moving Plastic Stress Field Ahead of the Crack Tip
Previous work has attempted, often within the framework of strip yield-type models, to predict crack growth rates based on the accumulation of fatigue damage ahead of the crack tip as it moves through a structure. This study performs similar calculations using results from plastic 2D plane stress analyses run on a finite element (FE) model containing a sharp semi-circular notch representing an edge crack. Stress-distance profiles ahead of the crack tip (notch root) were extracted at the maximum and minimum points of a range of fatigue cycles with different loading amplitudes. These were used with data from smooth specimen Low Cycle Fatigue (LCF) tests to predict the build-up of fatigue damage at regularly spaced locations ahead of the crack tip and hence crack growth rates. The FE analyses were performed for a wide range of Kmax values at loading R-ratios of 0, -1 and 0.5, and the growth rate predictions were compared with test data. The method was then extended to predict overload behaviour. The material studied was the nickel-based superalloy fine grain (FG) RR1000 at 20°C.
- 21 April 2026
- Published by MDPI AG in Preprints.org
Open AccessPredictions of Crack Growth Rates, R-Ratio and Overload Effects Based on Smooth Specimen LCF Data and the Moving Plastic Stress Field Ahead of the Crack Tip
Previous work has attempted, often within the framework of strip yield-type models, to predict crack growth rates based on the accumulation of fatigue damage ahead of the crack tip as it moves through a structure. This study performs similar calculations using results from plastic 2D plane stress analyses run on a finite element (FE) model containing a sharp semi-circular notch representing an edge crack. Stress-distance profiles ahead of the crack tip (notch root) were extracted at the maximum and minimum points of a range of fatigue cycles with different loading amplitudes. These were used with data from smooth specimen Low Cycle Fatigue (LCF) tests to predict the build-up of fatigue damage at regularly spaced locations ahead of the crack tip and hence crack growth rates. The FE analyses were performed for a wide range of Kmax values at loading R-ratios of 0, -1 and 0.5, and the growth rate predictions were compared with test data. The method was then extended to predict overload behaviour. The material studied was the nickel-based superalloy fine grain (FG) RR1000 at 20°C.
- Open Access
- 2 December 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 57 (5) , 1947-1961
Controlling Inter- and Intra-granular $\gamma ^{\prime} $ Through Heat TreatmentWrought Ni-based superalloys with low-processing cost and temperature capabilities beyond Alloy 718 are of significant interest for disk rotors in gas turbine engines. For these applications, damage tolerance and crack growth resistance are critical design priorities, particularly under conditions that produce time-dependent deformation from dwell fatigue cycles with sustained peak stresses. It is understood that dwell crack growth rates can be reduced by increasing grain size and by coarsening grain boundary $$\gamma ^{\prime} $$ to produce serrated grain boundaries. A heat treatment involving interrupted furnace cooling following solution heat treatment and secondary aging has been developed for a new potential low-processing cost alloy. This produced a fine grain size and coarse grain boundary $$\gamma ^{\prime} $$ whilst maintaining fine intragranular precipitates. Limited serration of grain boundaries was also achieved. The ultimate tensile strength of the alloy in this heat treatment condition exceeded that of Alloy 718 and approached that of Alloy 720 at $${650}\,^{\circ }$$ C and $${700}\,^{\circ }$$ C, although the yield strength was similar to, or below that of Alloy 718. Fatigue crack growth from 5 Hz cycles at $${650}\,^{\circ }$$ C was slow and largely transgranular, however, two tests with 120 seconds dwell cycles at $${650}\,^{\circ }$$ C both led to fast, intergranular crack growth, although there was a factor of 10 difference between the measured crack growth rates. The faster dwell fatigue crack rate was comparable to previously reported data for alloy ATI 718Plus. Both alloys have similarly high Nb contents, which likely contributed to the high rates of environmentally assisted cracking. Additionally, the significant spread of grain sizes observed could have allowed the crack to largely propagate along very fine grains, further accelerating crack growth and increasing the spread in the measured dwell fatigue crack growth resistance of the alloy.- 2 December 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 57 (5) , 1947-1961
Open AccessControlling Inter- and Intra-granular $\gamma ^{\prime} $ Through Heat TreatmentWrought Ni-based superalloys with low-processing cost and temperature capabilities beyond Alloy 718 are of significant interest for disk rotors in gas turbine engines. For these applications, damage tolerance and crack growth resistance are critical design priorities, particularly under conditions that produce time-dependent deformation from dwell fatigue cycles with sustained peak stresses. It is understood that dwell crack growth rates can be reduced by increasing grain size and by coarsening grain boundary $$\gamma ^{\prime} $$ to produce serrated grain boundaries. A heat treatment involving interrupted furnace cooling following solution heat treatment and secondary aging has been developed for a new potential low-processing cost alloy. This produced a fine grain size and coarse grain boundary $$\gamma ^{\prime} $$ whilst maintaining fine intragranular precipitates. Limited serration of grain boundaries was also achieved. The ultimate tensile strength of the alloy in this heat treatment condition exceeded that of Alloy 718 and approached that of Alloy 720 at $${650}\,^{\circ }$$ C and $${700}\,^{\circ }$$ C, although the yield strength was similar to, or below that of Alloy 718. Fatigue crack growth from 5 Hz cycles at $${650}\,^{\circ }$$ C was slow and largely transgranular, however, two tests with 120 seconds dwell cycles at $${650}\,^{\circ }$$ C both led to fast, intergranular crack growth, although there was a factor of 10 difference between the measured crack growth rates. The faster dwell fatigue crack rate was comparable to previously reported data for alloy ATI 718Plus. Both alloys have similarly high Nb contents, which likely contributed to the high rates of environmentally assisted cracking. Additionally, the significant spread of grain sizes observed could have allowed the crack to largely propagate along very fine grains, further accelerating crack growth and increasing the spread in the measured dwell fatigue crack growth resistance of the alloy. - Open Access
Corrosion Fatigue of a Nickel-Based Superalloy Disc Rotor with Salt in Air and Sulphur Dioxide Environments
The fatigue performance of a recently developed nickel superalloy disc was investigated at 700 °C in two environments: air and sulphur dioxide (SO2). Prior to testing, specimens were coated with various amounts of sodium sulphate (Na2SO4) and sodium chloride (NaCl) mixed salt (98% Na2SO4 + 2% NaCl), and the influence of both environment and salt loading on corrosion fatigue were assessed. Preliminary results showed that salt exposure in air reduced fatigue strength, with greater damage at higher salt levels. In the SO2 environment, fatigue strength dropped even more due to low-temperature hot corrosion (LTHC). The details of the corrosion morphology formed in both air and SO2 environments are discussed.
Open AccessCorrosion Fatigue of a Nickel-Based Superalloy Disc Rotor with Salt in Air and Sulphur Dioxide Environments
The fatigue performance of a recently developed nickel superalloy disc was investigated at 700 °C in two environments: air and sulphur dioxide (SO2). Prior to testing, specimens were coated with various amounts of sodium sulphate (Na2SO4) and sodium chloride (NaCl) mixed salt (98% Na2SO4 + 2% NaCl), and the influence of both environment and salt loading on corrosion fatigue were assessed. Preliminary results showed that salt exposure in air reduced fatigue strength, with greater damage at higher salt levels. In the SO2 environment, fatigue strength dropped even more due to low-temperature hot corrosion (LTHC). The details of the corrosion morphology formed in both air and SO2 environments are discussed.
- 21 August 2024
- Published by Springer Nature
- p. 707-718
Methods for Characterising Oxide Inclusions and Porosity in Powder Ni Alloys for Disk Rotor Applications
- 21 August 2024
- Published by Springer Nature
- p. 707-718
Methods for Characterising Oxide Inclusions and Porosity in Powder Ni Alloys for Disk Rotor Applications
- 21 August 2024
- Published by Springer Nature
- p. 267-277
High-Temperature Crack Growth Characteristics Under Dwell-Fatigue in a PM Superalloy for Disc Applications
- 21 August 2024
- Published by Springer Nature
- p. 267-277
High-Temperature Crack Growth Characteristics Under Dwell-Fatigue in a PM Superalloy for Disc Applications
- Open Access
- 30 July 2024
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 101 (5) , 1091-1102
Comparison of Performance of NiCr2O4 and Cr2O3 Formed on the Ni-Based Superalloy RR1000 Under Corrosive Conditions
Samples of the Ni-based superalloy, RR1000, were exposed to 98% Na2SO4/2% NaCl salts at 700 °C with a flux of 1.5 µg cm−2 h−1 in flowing air + 300 ppm SO2 for a total of 250 h. Three pre-exposure conditions were studied: a bare reference alloy; fast heating to the test temperature followed by a 100 h hold; heating at a rate of 5 °C min−1 to the test temperature following by a 100 h hold. The surface oxide formed under the latter two conditions were Cr2O3 or NiCr2O4, respectively. The results show corrosion pit formation on the surface of the base, reference sample, and no pits present on the sample with the preformed Cr2O3. Some protection was found for the sample heated at 5 °C min−1 with a delay in the progression to accelerated corrosion attack. Additional testing under moisture containing air was also conducted. This showed no obvious difference in surface oxide morphology under the two tested heating rates for the short-term exposures examined but a difference was noted to be dependent on the moisture content of the air.
- 30 July 2024
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 101 (5) , 1091-1102
Open AccessComparison of Performance of NiCr2O4 and Cr2O3 Formed on the Ni-Based Superalloy RR1000 Under Corrosive Conditions
Samples of the Ni-based superalloy, RR1000, were exposed to 98% Na2SO4/2% NaCl salts at 700 °C with a flux of 1.5 µg cm−2 h−1 in flowing air + 300 ppm SO2 for a total of 250 h. Three pre-exposure conditions were studied: a bare reference alloy; fast heating to the test temperature followed by a 100 h hold; heating at a rate of 5 °C min−1 to the test temperature following by a 100 h hold. The surface oxide formed under the latter two conditions were Cr2O3 or NiCr2O4, respectively. The results show corrosion pit formation on the surface of the base, reference sample, and no pits present on the sample with the preformed Cr2O3. Some protection was found for the sample heated at 5 °C min−1 with a delay in the progression to accelerated corrosion attack. Additional testing under moisture containing air was also conducted. This showed no obvious difference in surface oxide morphology under the two tested heating rates for the short-term exposures examined but a difference was noted to be dependent on the moisture content of the air.
- Open Access
- 24 June 2023
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 100 (1-2) , 65-83
Temperature Range of Heating Rate Dependent Reactions Leading to Spinel Formation on a Ni-Based Superalloy
Improved oxidation kinetics for a polycrystalline Ni-based superalloy used in turbine disc applications has been shown to be possible by controlling the heating rate of the first thermal exposure to 5 °C min−1. The beneficial effect arises from the formation of a protective layer of NiCr2O4, instead of the more usually formed doped Cr2O3. This study shows that it was possible to form the NiCr2O4 at temperatures up to 725 °C, within the operational conditions for this alloy, and that at higher temperatures Cr2O3 formed. The improvements in alloy performance extended to the internal oxidation processes where reduced depths of degradation were observed. It is demonstrated here that Al2O3 formation is less thermodynamically stable when the highly protective NiCr2O4 oxide is present at the alloy surface compared to the doped Cr2O3. Synchrotron XRD was performed on samples removed during the heating stage and provided evidence of the oxidation sequence occurring, enabling refinement in the thermodynamic calculations and suggesting an additional route to the formation of the NiCr2O4.
- 24 June 2023
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 100 (1-2) , 65-83
Open AccessTemperature Range of Heating Rate Dependent Reactions Leading to Spinel Formation on a Ni-Based Superalloy
Improved oxidation kinetics for a polycrystalline Ni-based superalloy used in turbine disc applications has been shown to be possible by controlling the heating rate of the first thermal exposure to 5 °C min−1. The beneficial effect arises from the formation of a protective layer of NiCr2O4, instead of the more usually formed doped Cr2O3. This study shows that it was possible to form the NiCr2O4 at temperatures up to 725 °C, within the operational conditions for this alloy, and that at higher temperatures Cr2O3 formed. The improvements in alloy performance extended to the internal oxidation processes where reduced depths of degradation were observed. It is demonstrated here that Al2O3 formation is less thermodynamically stable when the highly protective NiCr2O4 oxide is present at the alloy surface compared to the doped Cr2O3. Synchrotron XRD was performed on samples removed during the heating stage and provided evidence of the oxidation sequence occurring, enabling refinement in the thermodynamic calculations and suggesting an additional route to the formation of the NiCr2O4.
- 21 April 2023
- Published by Springer Nature
- p. 29-47
The Effect of Microstructure on the Strength of VDM Alloy 780
- 21 April 2023
- Published by Springer Nature
- p. 29-47
The Effect of Microstructure on the Strength of VDM Alloy 780