A. Albizane
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
A. Albizane has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Jamal Bennazha
Mohammedia Univ Hassan II Casablanca, Fac Sci & Technol, Lab Mat Mem & Environm, Casablanca, Morocco
2 shared publications - M. Persin
European Institute of Membranes, 1919 Route de Mende, Montpellier, Cedex 5 34293, France, Tel. +33 4 67 613402
2 shared publications - Saad Alami Younssi
Mohammedia Univ Hassan II Casablanca, Fac Sci & Technol, Lab Mat Mem & Environm, Casablanca, Morocco
2 shared publications - A. Kabbabi
Research Center for Studies on Mineral Phosphates (CERPHOS), 73 Boulevard Moulay Ismail, Casablanca, Morocco, Tel. +212 522 241269
1 shared publication A. Larbot
Institut Européen des Membranes, UMR 5635 CNRS ENSCM UMII, 1919 Route de Mende 34293 Montpellier Cedex 5, France
1 shared publication- Brahim Achiou
Laboratory of Materials, Membranes and Environment, Faculty of Sciences and Technologies Mohammedia, Hassan II University of Casablanca, Casablanca 21100, Morocco
1 shared publication
Latest Publications
- Open Access
- 1 September 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (43) , 20298-20306
Elaboration and characterization of flat membrane supports from Moroccan clays. Application for the treatment of wastewater
In this work, ceramic supports for microfiltration have been made and thoroughly characterized from three Moroccan clays: clay of Meknes (CM), fine clay of Fès (FCF), and granular clay of Fès (GCF). X-ray fluorescence (XRF), X-ray diffraction, and thermogravimetric analysis (TGA) techniques were used to characterize the raw material. Flat disks of 3.6 cm of diameter and 1.5 mm in thickness were prepared from the natural clays: the powder was crushed and sieved to 63 μm. The obtained powder was then pressed without organic additives and without water addition to elaborate a porous structure. Finally, a thermal treatment was carried out in a programmable oven at different final temperatures; the best firing temperature of the support is 950°C. The resulting supports have been characterized by scanning electron microscopy, water porosity, corrosion resistance and mechanical strength. The porosity of the supports CM, FCF, and GCF was, respectively, 28.1, 30.8 and 40%, and the average pore diameter was 1.8 μm for the CM support, 1.50 μm for FCF support and 2.84 μm for GCF support. Elaborated flat supports have been used to treat colored solutions to verify the suitability of such filters in the preclarification step in wastewater treatment for Moroccan industry. Results showed a good retention of turbidity and conductivity for the three elaborated supports.
- 1 September 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (43) , 20298-20306
Open AccessElaboration and characterization of flat membrane supports from Moroccan clays. Application for the treatment of wastewater
In this work, ceramic supports for microfiltration have been made and thoroughly characterized from three Moroccan clays: clay of Meknes (CM), fine clay of Fès (FCF), and granular clay of Fès (GCF). X-ray fluorescence (XRF), X-ray diffraction, and thermogravimetric analysis (TGA) techniques were used to characterize the raw material. Flat disks of 3.6 cm of diameter and 1.5 mm in thickness were prepared from the natural clays: the powder was crushed and sieved to 63 μm. The obtained powder was then pressed without organic additives and without water addition to elaborate a porous structure. Finally, a thermal treatment was carried out in a programmable oven at different final temperatures; the best firing temperature of the support is 950°C. The resulting supports have been characterized by scanning electron microscopy, water porosity, corrosion resistance and mechanical strength. The porosity of the supports CM, FCF, and GCF was, respectively, 28.1, 30.8 and 40%, and the average pore diameter was 1.8 μm for the CM support, 1.50 μm for FCF support and 2.84 μm for GCF support. Elaborated flat supports have been used to treat colored solutions to verify the suitability of such filters in the preclarification step in wastewater treatment for Moroccan industry. Results showed a good retention of turbidity and conductivity for the three elaborated supports.
- Open Access
- 1 June 2015
- Published by Elsevier in Desalination and Water Treatment
- Vol. 55 (1) , 53-60
New ceramic membranes from natural Moroccan phosphate for microfiltration application
This paper is devoted to preparation of low-cost microfiltration (MF) membranes using lixiviated phosphate powder crushed at 50 μm. The filtering layer was coated on phosphate tubular support with 10 μm pore diameter and 43% porosity. The preparation of this ceramic layer was performed by the slip-casting method. A deflocculated slip was obtained by mixing mineral powder, polyvinyl alcohol, and water with dispersant. After drying at room temperature for 24 h, the MF layer was heated to 800°C for consolidation. Scanning electron microscopy observation showed homogeneous layers without cracks with an average pore diameter of 0.35 μm for the active layer, the thickness is approximately 10 μm. Water permeability obtained is about 700 L/h m2 bar. The membranes have been tested to treat wastewater of phosphate industry, to clarify synthetic solutions of lime and aluminum hydroxide, and to remove bacteriological pollution present in water wells. The experiments carried out show that elaborated MF membrane is very efficient for the reduction of turbidity, total phosphorus, and number of bacterial germs with almost the same performances than that obtained with a commercial α-alumina membrane.
- 1 June 2015
- Published by Elsevier in Desalination and Water Treatment
- Vol. 55 (1) , 53-60
Open AccessNew ceramic membranes from natural Moroccan phosphate for microfiltration application
This paper is devoted to preparation of low-cost microfiltration (MF) membranes using lixiviated phosphate powder crushed at 50 μm. The filtering layer was coated on phosphate tubular support with 10 μm pore diameter and 43% porosity. The preparation of this ceramic layer was performed by the slip-casting method. A deflocculated slip was obtained by mixing mineral powder, polyvinyl alcohol, and water with dispersant. After drying at room temperature for 24 h, the MF layer was heated to 800°C for consolidation. Scanning electron microscopy observation showed homogeneous layers without cracks with an average pore diameter of 0.35 μm for the active layer, the thickness is approximately 10 μm. Water permeability obtained is about 700 L/h m2 bar. The membranes have been tested to treat wastewater of phosphate industry, to clarify synthetic solutions of lime and aluminum hydroxide, and to remove bacteriological pollution present in water wells. The experiments carried out show that elaborated MF membrane is very efficient for the reduction of turbidity, total phosphorus, and number of bacterial germs with almost the same performances than that obtained with a commercial α-alumina membrane.
- 15 February 2008
- Published by Elsevier in Separation and Purification Technology
- Vol. 59 (2) , 134-140
Investigation of performance of a low ZnAl2O4–TiO2 ultrafiltration membrane in relation with speciation and membrane solutes interactions
- 15 February 2008
- Published by Elsevier in Separation and Purification Technology
- Vol. 59 (2) , 134-140
Investigation of performance of a low ZnAl2O4–TiO2 ultrafiltration membrane in relation with speciation and membrane solutes interactions