Philipp Spenhoff
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Philipp Spenhoff has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Marco Semini
Department of Mechanical and Industrial Engineering, Norwegian University of Science and Technology, NTNU, Trondheim, Norway
2 shared publications- Daryl Powell
University of South-Eastern Norway
1 shared publication Erlend Alfnes
Norwegian University of Science and Technology
1 shared publication- J.(Hans) C. Wortmann
University of Groningen
1 shared publication Jan Ola Strandhagen
Norwegian University of Science and Technology
1 shared publication- Marco Semini
Norwegian University of Science and Technology
1 shared publication
Latest Publications
- Open Access
- 26 February 2021
- Published by Taylor & Francis in Production Planning & Control
- Vol. 33 (14) , 1337-1354
EPEC 4.0: an Industry 4.0-supported lean production control concept for the semi-process industry
The combination of lean production and Industry 4.0 exhibits excellent potential in advancing operations management and, especially, production control. This improvement potential is applicable to the semi-process industry (S-PI), as higher product variety and higher demand variability require greater flexibility from production systems. This flexibility is difficult to achieve in S-PI environments, in which it is imperative to cope with the long setup times and stability needed for the high utilization requirements. Heijunka addresses this stability-flexibility paradox but was designed for short setup times and is thus considered not directly applicable. In this article, we use design science research to adapt Heijunka to the S-PI and combine it with cyber-physical systems technologies. The developed production control concept, every product every cycle (EPEC) 4.0, aims to schedule the production system as efficiently as possible, providing the necessary flexibility and minimum schedule perturbation. Furthermore, we present the findings from a validation case study within the automotive supply industry.
- 26 February 2021
- Published by Taylor & Francis in Production Planning & Control
- Vol. 33 (14) , 1337-1354
Open AccessEPEC 4.0: an Industry 4.0-supported lean production control concept for the semi-process industry
The combination of lean production and Industry 4.0 exhibits excellent potential in advancing operations management and, especially, production control. This improvement potential is applicable to the semi-process industry (S-PI), as higher product variety and higher demand variability require greater flexibility from production systems. This flexibility is difficult to achieve in S-PI environments, in which it is imperative to cope with the long setup times and stability needed for the high utilization requirements. Heijunka addresses this stability-flexibility paradox but was designed for short setup times and is thus considered not directly applicable. In this article, we use design science research to adapt Heijunka to the S-PI and combine it with cyber-physical systems technologies. The developed production control concept, every product every cycle (EPEC) 4.0, aims to schedule the production system as efficiently as possible, providing the necessary flexibility and minimum schedule perturbation. Furthermore, we present the findings from a validation case study within the automotive supply industry.
- 29 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 961-965
Investigating production planning and control challenges in the semi-process industry, the case of a metal parts producer
Production planning and control (PPC) plays a vital role for the competitiveness of every company. Its application in the process industries still faces major problems and limitations. The process industries are currently facing an increasing trend in demand variability and uncertainty. Too little is known about the link between industry specific characteristics and matching PPC approaches. In this paper, we investigate the characteristics that pose critical challenges when applying PPC concepts in the semi-process industry. The results of our study show a conflict between flexibility-requiring and flexibility-limiting characteristics. Through the use of a literature review and case study we demonstrate the limitations of material requirements planning to address this new situation.
- 29 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 961-965
Investigating production planning and control challenges in the semi-process industry, the case of a metal parts producer
Production planning and control (PPC) plays a vital role for the competitiveness of every company. Its application in the process industries still faces major problems and limitations. The process industries are currently facing an increasing trend in demand variability and uncertainty. Too little is known about the link between industry specific characteristics and matching PPC approaches. In this paper, we investigate the characteristics that pose critical challenges when applying PPC concepts in the semi-process industry. The results of our study show a conflict between flexibility-requiring and flexibility-limiting characteristics. Through the use of a literature review and case study we demonstrate the limitations of material requirements planning to address this new situation.
- Open Access
- 11 June 2014
- Published by Springer Nature in Advances in Manufacturing
- Vol. 2 (2) , 165-172
The fit of planning methods for the part manufacturing industry, a case study
- 11 June 2014
- Published by Springer Nature in Advances in Manufacturing
- Vol. 2 (2) , 165-172
Open AccessThe fit of planning methods for the part manufacturing industry, a case study