MKMilan Kovačič

Milan Kovačič

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Milan Kovačič has a total of 50 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Interplay of Aspect Ratio and Emission Dipole Orientation for Light Extraction in Corrugated Red, Green and Blue OLEDs

    by Milan Kovačič, Janez Krč, Marko Topič

    Using advanced optical modelling, we quantify how sinusoidal corrugation and emitter dipole orientation jointly govern light extraction from OLED thin-film stacks into a glass substrate for red, green, and blue emission. Irrespective of emission colour, the corrugation aspect ratio (AR = height/period) is the dominant geometric parameter controlling extraction, with absolute period and height playing secondary roles, as periods of 600–1000 nm deliver similar gains across all colours. Extraction peaks at AR ≈ 0.2 for predominantly horizontal dipoles, AR ≈ 0.5 for vertical dipoles, and AR ≈ 0.3 for isotropic orientations. For the isotropic case, extraction improves by up to 40%, 34%, and 20% relative to flat red, green, and blue devices, respectively. Absorption analysis attributes the principal gains to suppression of surface-plasmon-polariton losses of vertical dipoles, supported by local dipole reorientation, waveguide disruption, and scattering. Because practical texturing can alter dipole orientation, optimum conditions must be re-evaluated; if orientations follow the sinusoidal profile, an AR of approximately 0.2–0.3 is favoured for isotropic to moderately horizontal orientations, whereas higher ARs benefit strongly vertical orientations. The results provide guidelines for co-optimising corrugation geometry and dipole orientation for high-efficiency OLEDs.

  • Open Access

    Improving Light Outcoupling and Addressing Measurement Specifics in Perovskite Light‐Emitting Diodes with Light Management Foils

    by Milan Kovačič, Marko Jošt, Janez Krč, Marko Topič

    Near‐infrared perovskite light‐emitting diodes (PeLEDs), with four perovskite (PK) layer thicknesses and optional micro‐textured light management (LM) foil, are fabricated to evaluate their effects on light outcoupling efficiency. Devices with a 70 nm thick PK exhibit highest external quantum efficiencies (EQE), compared to those with thinner or thicker PK layers. The PK thickness influences the overall thin‐film stack and, consequently, the light outcoupling. LM foils significantly improve light outcoupling across all devices, with the thickest PK layer (160 nm) benefiting the most (60% increase), while the thinnest (40 nm) sees the least improvement (30%). Measured trends align well with optical modeling results, further highlighting the impact of sample holder design and pixel position on results. Theoretical optimization of PK thickness indicates unique optimal values for devices with or without LM foils. For devices incorporating LM foils, simulations predict an optimal PK thickness of 80 nm and an EQE of 27%. In contrast, for devices without LM foils, the optimal PK thickness of 60 nm corresponds to simulated EQE of 17%. In all cases, LM foils significantly enhance light outcoupling from bottom‐emitting PeLEDs while emphasizing the necessity to include LM foils in the thin‐film layer stack optimization process.


  • Design of external microtextures for efficient light outcoupling in OLEDs with different preferential orientation of emission dipoles

    by Milan Kovačič

    External light outcoupling structures provide a cost-effective and highly efficient solution for light extraction in organic light-emitting diodes. Among them, different microtextures, mainly optimized for devices with isotopically oriented emission dipoles, have been proposed as an efficient light extraction solution. In the paper, the outcoupling for a preferential orientation of emission dipoles is studied for the case of a red bottom-emitting organic light-emitting diode. Optical simulations are used to analyse the preferential orientation of dipoles in combination with three different textures, namely hexagonal array of sine-textures, three-sided pyramids, and random pyramids. It is shown that while there are minimal differences between the optimized textures, the highest external quantum efficiency of 51% is predicted by using the three-sided pyramid texture. Further improvements, by employing highly oriented dipole sources, are examined. In this case, the results show that the top outcoupling efficiencies can be achieved with the same texture shape and size, regardless of the preferred orientation of the emission dipoles. Using an optimized three-sided pyramid in combination with ideally parallel oriented dipoles, an efficiency of 62% is achievable. A detailed analysis of the optical situation inside the glass substrate, dominating external light outcoupling, is presented. Depicted results and their analysis offer a simplified further research and development of external light extraction for organic light-emitting devices with highly oriented dipole emission sources.

  • Open Access

    Optical Simulation Study of Perovskite/CIGS Tandem Solar Cells With Reduced Graphene Oxide Layers

    by Milan Kovačič, Janez Krč, Kyriaki Savva, Stella Maragkaki, Emmanuel Stratakis, Mudasar Rashid, Merve Tutundzic, Yinghuan Kuang, Jessica de Wild, Tom Aernouts, et al.

    Tandem solar cells present a promising solution to overcome the Schottky–Queisser efficiency limit of single-junction solar cells. In this article, an all–thin-film tandem solar cell based on perovskite (PK) top cell and chalcopyrite Cu (In, Ga) Se2 (CIGS) bottom cell is researched. Device optical simulations are validated on the top and bottom cells and employed for the analysis of PK/CIGS tandem cells. In particular, the optical effects of introduced laser reduced graphene oxide (rGO) layers at two positions in the tandem cell: 1) at the position between the top PK and bottom CIGS cell and 2) underneath the front transparent electrode. The purpose of introducing rGO layers is to improve the optoelectrical properties of the device, based on the tunable electronic and optical characteristics of rGO layers. Optical simulation results show that the parasitic absorption in rGO layers may noticeably affect the optical performance of the tandem cell if the layers are not optimized. The use of a thin and a few nanometer-thick rGO is suggested from the analysis if its parasitic absorption is not reduced. Directions for further optimization of optical rGO, including the reduction of parasitic absorption and tuning of the real part of the refractive index, are performed.


  • Analysis and optimization of light outcoupling in OLEDs with external hierarchical textures

    by Milan Kovačič, Dinara Samigullina, Felix Bouchard, Janez Krč, Benjamin Lipovšek, Marcos Soldera, Andrés Fabián Lasagni, Sebastian Reineke, Marko Topič

    Hierarchical textures (combining 2D periodic large and small micro textures) as an external outcoupling solution for OLEDs have been researched, both experimentally and by optical simulations. For the case of a red bottom emitting OLED, different hierarchical textures were fabricated using laser-based methods and a replication step and applied to the OLED substrate, resulting in an increased light outcoupling. Laboratory-size OLED devices with applied textured foils show a smaller increase in efficiency compared to the final large area devices. The results show that the full exploitation of textured foils in laboratory-size samples is mainly limited by the lateral size of the thin film stack area and by limited light collection area of the measuring equipment. Modeling and simulations are used to further evaluate the full prospective of hierarchical textures in large area OLED devices. Optimization of hierarchical textures is done by simultaneously changing the aspect ratios of the small and large textures and a potential of 57% improvement in EQE compared to devices without applied textures is predicted by simulations. Optimized hierarchical textures show similar outcoupling efficiencies compared to optimized single textures, while on the other hand hierarchical textures require less pronounced features, lower aspect ratios, compared to single textures to achieve the same efficiencies. Hierarchical textures also help in eliminating flat parts that limit outcoupling efficiency. Finally, the limiting factors that prevent higher outcoupling are addressed. We show that the dominant factor is non-ideal reflection from the organic thin film stack due to parasitic absorption. In addition, possible ways to further increase the outcoupling from a thick substrate are indicated.


  • Open Access

    Effect of Dipole Position and Orientation on Light Extraction for Red OLEDs on Periodically Corrugated Substrate - FEM Simulations Study

    by Milan Kovačič

    One of the main efficiency-limiting factors for organic light-emitting diodes (OLEDs) is poor light extraction, which typically reaches only 20% (in best cases up to 30%) in flat standard devices. Optical modeling and simulations play an important role in improving light extraction and optimizing outcoupling efficiency. Using FEM modeling approach, the effect of dipole positions and orientations for red OLEDs on periodically corrugated substrate is evaluated and used to enhance the outcoupling efficiency. It is shown that with only 3 carefully selected dipole positions, the outcoupling efficiency over the whole area can be predicted with very reasonable accuracy, which greatly reduces the number of simulations required. The presented modelling approach is used for optimization of the sine texture as a substrate corrugation structure. OLEDs with optimized simulated texture show a relative improvement of light outcoupling from the thin film stack to the substrate by more than 25% compared to the flat plane devices.


  • Light Management Foils with Hierarchical Textures for Light Outcoupling in OLEDs

    by Milan Kovačič, Felix Bouchard, Marcos Soldera, Andrés Fabián Lasagni, Dinara Samigullina, Janez Krč, Simone Lenk, Benjamin Lipovšek, Sebastian Reineke, Marko Topič

    Hierarchical textures are researched experimentally and by optical simulations in the role of external outcoupling solution for OLEDs. Their full outcoupling potential, limiting factors and pathways for further increase in outcoupling are addressed.

  • Optimization of Back Contact Grid Size in Al2O3-Rear-Passivated Ultrathin CIGS PV Cells by 2-D Simulations

    by Jackson Lontchi, Maria Zhukova, Milan Kovacic, Janez Krc, Wei-Chao Chen, Marika Edoff, Sourav Bose, Pedro M. P. Salome, Julie Goffard, Andrea Cattoni, et al.

    We present a simulation strategy using ATLAS-2D to optimize the back-contact hole grid (i.e., size and pitch of openings) of the Al 2 O 3 -rear-passivation layer in ultrathin Cu(In,Ga)Se 2 photovoltaic cells. We first discuss and compare our simulation model with a series of experimental nonpassivated and passivated cells to decouple the crucial passivation parameters. The simulation results follow the experimental trends, highlighting the beneficial effects of the passivation on the cell performances. Furthermore, it stresses the influence of the passivation quality at the Al 2 O 3 /Cu(In,Ga)Se 2 (CIGS) interface and of the contact resistance at the Mo/CIGS interface within the openings. Further simulations quantify significant improvements in short-circuit current and open-circuit voltage for different sizes of openings in the Al 2 O 3 layer, relative to an excellent passivation quality (i.e., high density of negative charges in the passivation layer). However, a degradation is predicted for a poor passivation (i.e., low density of such charges) or a high contact resistance. Consequently, we point out an optimum in efficiency when varying the opening widths at fixed hole-pitch and fixed contact resistance. At equivalent contact resistance, simulations predict that the sizes of the pitch and openings can be increased without optimal performance losses when maintaining a width to pitch ratio around 0.2. This simulation trends have been confirmed by a series of experiments, indicating that it is crucial to care about the dimensions of the opening grid and the contact resistance of passivated cells. These simulation results provide significant insights for optimal cell design and characterizations of passivated UT-CIGS PV cells.


  • Open Access

    Modelling Supported Design of Light Management Structures in Ultra-Thin Cigs Photovoltaic Devices

    by M. Kovačič, J. Krč, B. Lipovšek, W-C Chen, M. Edoff, P.J. Bolt, J. van Deelen, M. Zhukova, J. Lontchi, D. Flandre, et al.

    Modelling Supported Design of Light Management Structures in Ultra-Thin Cigs Photovoltaic Devices


  • Light management design in ultra-thin chalcopyrite photovoltaic devices by employing optical modelling

    by M. Kovacic, J. Krc, B. Lipovsek, W.-C. Chen, M. Edoff, P.J. Bolt, J. van Deelen, M. Zhukova, J. Lontchi, D. Flandre, et al.