Aziah Khamis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aziah Khamis has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Raja Nor Firdaus
Universiti Teknikal Malaysia Melaka
2 shared publications A. A. Rahman
Faculty of Electrical Engineering, UTeM
1 shared publication- Ahmad Fuad Ab Ghani
Universiti Teknikal Malaysia Melaka (UTeM)
1 shared publication Azah Mohamed
Department of Electrical, Electronic and System Engineering Universiti Kebangsaan Malaysia Malaysia
1 shared publication- Azah Mohamed
Universiti Kebangsaan Malaysia
1 shared publication - Azrita Alias
Universiti Teknikal Malaysia Melaka
1 shared publication
Latest Publications
- Open Access
- 23 June 2026
- Published by Kaunas University of Technology (KTU) in Environmental Research, Engineering and Management
- Vol. 82 (2) , 80-101
Hybrid PSO–L-BFGS-B Optimization of Small-Scale HAWTs for Low-Wind Tropical Sites: Blades Length and Hub Height Tuning with Multi-Site Indonesian Data
Wind energy, offers strong potential for tropical regions, yet low and variable wind speeds limit the efficiency of conventional turbines. Therefore, this study proposes a hybrid optimization technique integrating particle swarm optimization (PSO) with the Limited-memory Broyden-Fletcher-Goldfarb-Shanno (L-BFGS-B) algorithm to determine the optimal blade length and hub height of small-scale horizontal axis wind turbines (HAWTs). Multi-year wind datasets (2017–2020) from five Indonesian sites Jambi, South Sulawesi, NTB, NTT, and Maluku were statistically characterized using Weibull and Bi-Weibull distribution and incorporated into annual energy production (AEP) modelling. The hybrid PSO–L-BFGS-B method achieved 5–15% higher AEP than standard PSO, and 11–25% higher AEP compared to the baseline TSD-500 turbine, while also exhibiting smoother convergence and reduced interquartile variability across 30 independent runs. Sensitivity analysis showed that hub height exerts a stronger influence on AEP than blade length, reflecting the aerodynamic advantage of elevated rotors under low-wind tropical conditions. The results demonstrate that hybrid meta-heuristic optimization effectively tailors small-scale wind turbines for reliable and sustainable energy generation in tropical developing regions.
- 23 June 2026
- Published by Kaunas University of Technology (KTU) in Environmental Research, Engineering and Management
- Vol. 82 (2) , 80-101
Open AccessHybrid PSO–L-BFGS-B Optimization of Small-Scale HAWTs for Low-Wind Tropical Sites: Blades Length and Hub Height Tuning with Multi-Site Indonesian Data
Wind energy, offers strong potential for tropical regions, yet low and variable wind speeds limit the efficiency of conventional turbines. Therefore, this study proposes a hybrid optimization technique integrating particle swarm optimization (PSO) with the Limited-memory Broyden-Fletcher-Goldfarb-Shanno (L-BFGS-B) algorithm to determine the optimal blade length and hub height of small-scale horizontal axis wind turbines (HAWTs). Multi-year wind datasets (2017–2020) from five Indonesian sites Jambi, South Sulawesi, NTB, NTT, and Maluku were statistically characterized using Weibull and Bi-Weibull distribution and incorporated into annual energy production (AEP) modelling. The hybrid PSO–L-BFGS-B method achieved 5–15% higher AEP than standard PSO, and 11–25% higher AEP compared to the baseline TSD-500 turbine, while also exhibiting smoother convergence and reduced interquartile variability across 30 independent runs. Sensitivity analysis showed that hub height exerts a stronger influence on AEP than blade length, reflecting the aerodynamic advantage of elevated rotors under low-wind tropical conditions. The results demonstrate that hybrid meta-heuristic optimization effectively tailors small-scale wind turbines for reliable and sustainable energy generation in tropical developing regions.
- Open Access
- 1 September 2024
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 35 (3) , 1412-1425
Improvement of electromagnetic torque of BLDC motor for electrical cutter application
As the advancement of brushless direct current (BLDC) motor is rising, it has been an advantage to use the motor for a wide range of applications. Its robustness and torque development have benefited small applications, such as the agriculture cutter. However, dropping performances of conventional BLDC are affected by the shape of the rotor that has unused magnetic flux. Therefore, this research aimed to analyze the electromagnetic torque by reducing the unused flux from an electromagnetic point of view. Two BLDC models with different slot-pole numbers and rotor types were modeled and simulated with equal permanent magnet volume, and magnetomotive force (MMF). Finite element method (FEM) software was used to compute back electromotive force (BEMF), cogging torque, electromagnetic torque, and magnetic flux density of the BLDC models. As a result, 9/8 slot-pole with zero ferromagnetic underneath the permanent magnet had the highest BEMF and torque produced compared to the conventional type, with a percentage difference of 27%. In conclusion, this research presents the motor that had an improvement of electromagnetic torque for electrical cutter application.
- 1 September 2024
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 35 (3) , 1412-1425
Open AccessImprovement of electromagnetic torque of BLDC motor for electrical cutter application
As the advancement of brushless direct current (BLDC) motor is rising, it has been an advantage to use the motor for a wide range of applications. Its robustness and torque development have benefited small applications, such as the agriculture cutter. However, dropping performances of conventional BLDC are affected by the shape of the rotor that has unused magnetic flux. Therefore, this research aimed to analyze the electromagnetic torque by reducing the unused flux from an electromagnetic point of view. Two BLDC models with different slot-pole numbers and rotor types were modeled and simulated with equal permanent magnet volume, and magnetomotive force (MMF). Finite element method (FEM) software was used to compute back electromotive force (BEMF), cogging torque, electromagnetic torque, and magnetic flux density of the BLDC models. As a result, 9/8 slot-pole with zero ferromagnetic underneath the permanent magnet had the highest BEMF and torque produced compared to the conventional type, with a percentage difference of 27%. In conclusion, this research presents the motor that had an improvement of electromagnetic torque for electrical cutter application.
- 15 May 2024
- Published by Virtual Company of Physics in Journal of Ovonic Research
- Vol. 20 (3) , 309-323
Absorber layer improvement and performance analysis of CIGS thin-film solar cell
- 15 May 2024
- Published by Virtual Company of Physics in Journal of Ovonic Research
- Vol. 20 (3) , 309-323
Absorber layer improvement and performance analysis of CIGS thin-film solar cell
- Open Access
- 1 January 2024
- Published by Wiley in International Journal of Energy Research
- Vol. 2024 (1)
An Effective Islanding Detection Method for Distributed Generation Integrated Power Systems Using Gabor Transform Technique and Artificial Intelligence Techniques
Incorporating distributed generation (DG) technology into modern power systems heralds a multitude of technological, economic, and environmental advantages. These encompass enhanced reliability, reduction in power losses, heightened efficiency, low initial investment requirements, abundant availability, and a minimized environmental footprint. However, the rapid detection and disconnection of DG units during islanding events are paramount to circumvent safety hazards and potential equipment damage. Although passive techniques are predominantly utilized for islanding protection due to their minimal systemic interference, their susceptibility to substantial nondetection zones (NDZ) instigates a transition toward more innovative techniques. Addressing this crucial need, the study employs a novel amalgamation of signal processing methodologies and a suite of intelligent classifiers to augment the detection of islanding events in power systems. Concealed features from a variety of signals are extracted by the methodology and utilized as robust inputs to the intelligent classifiers. This empowers these classifiers to make a reliable distinction between islanding events and other types of disturbances. The breadth of the study is expanded to evaluate a range of sophisticated models including gradient boosting, decision tree–based models, and multilayer perceptrons (MLPs). These models are thoroughly tested on a radial distribution system integrated with two DG units and subjected to rigorous simulations and comparative analysis using the DIgSILENT Power Factory software. The findings underscore the efficacy of the proposed method, showcasing a significant improvement over conventional techniques in terms of efficiency and resilience. Above all, the methodology exhibits an exceptional ability to discriminate between islanding events and other system disturbances. Specifically, the islanding detection method demonstrated a detection time of less than one cycle (20 ms), ensuring rapid response. Moreover, the proposed algorithm demonstrated the capability to detect all ranges of power mismatch, including zero‐power mismatch, thereby eliminating the NDZ. These results illuminate the benefits of integrating signal processing methodologies with intelligent classifiers, marking a significant stride forward in the realm of islanding event detection.
- 1 January 2024
- Published by Wiley in International Journal of Energy Research
- Vol. 2024 (1)
Open AccessAn Effective Islanding Detection Method for Distributed Generation Integrated Power Systems Using Gabor Transform Technique and Artificial Intelligence Techniques
Incorporating distributed generation (DG) technology into modern power systems heralds a multitude of technological, economic, and environmental advantages. These encompass enhanced reliability, reduction in power losses, heightened efficiency, low initial investment requirements, abundant availability, and a minimized environmental footprint. However, the rapid detection and disconnection of DG units during islanding events are paramount to circumvent safety hazards and potential equipment damage. Although passive techniques are predominantly utilized for islanding protection due to their minimal systemic interference, their susceptibility to substantial nondetection zones (NDZ) instigates a transition toward more innovative techniques. Addressing this crucial need, the study employs a novel amalgamation of signal processing methodologies and a suite of intelligent classifiers to augment the detection of islanding events in power systems. Concealed features from a variety of signals are extracted by the methodology and utilized as robust inputs to the intelligent classifiers. This empowers these classifiers to make a reliable distinction between islanding events and other types of disturbances. The breadth of the study is expanded to evaluate a range of sophisticated models including gradient boosting, decision tree–based models, and multilayer perceptrons (MLPs). These models are thoroughly tested on a radial distribution system integrated with two DG units and subjected to rigorous simulations and comparative analysis using the DIgSILENT Power Factory software. The findings underscore the efficacy of the proposed method, showcasing a significant improvement over conventional techniques in terms of efficiency and resilience. Above all, the methodology exhibits an exceptional ability to discriminate between islanding events and other system disturbances. Specifically, the islanding detection method demonstrated a detection time of less than one cycle (20 ms), ensuring rapid response. Moreover, the proposed algorithm demonstrated the capability to detect all ranges of power mismatch, including zero‐power mismatch, thereby eliminating the NDZ. These results illuminate the benefits of integrating signal processing methodologies with intelligent classifiers, marking a significant stride forward in the realm of islanding event detection.
- Open Access
- 1 September 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Evaluation and Research in Education (IJERE)
- Vol. 12 (3) , 1550-1559
Individual student key performance using mobile web apps based on knowledge profile and cumulative grade point average
This study investigated the performance of individual students toward the knowledge profile and cumulative grade point average or known as CGPA. The proposal of this paper involves two major components. The first component is investigating the individual student performance based on the knowledge profile and CGPA. The performance of students from cohort 2017 for the program Bachelor of Electrical Engineering (BEKG) courses in the Faculty of Electrical Engineering, Universiti Teknikal Malaysia Melaka (UTeM) was used as the dataset. The case study separates into various groups (excellent, honors and pass). Secondly, the study proposed a responsive web application leveraging a Google Visualization Feature to self-check individual academic performance. The goal of this app is to assist users in evaluating individual student performance and assist management in planning for continual quality improvement using the web and mobile apps. The marketing segments include students, academics, university, and school administration for analysis and evaluate the individual student’s performance.
- 1 September 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Evaluation and Research in Education (IJERE)
- Vol. 12 (3) , 1550-1559
Open AccessIndividual student key performance using mobile web apps based on knowledge profile and cumulative grade point average
This study investigated the performance of individual students toward the knowledge profile and cumulative grade point average or known as CGPA. The proposal of this paper involves two major components. The first component is investigating the individual student performance based on the knowledge profile and CGPA. The performance of students from cohort 2017 for the program Bachelor of Electrical Engineering (BEKG) courses in the Faculty of Electrical Engineering, Universiti Teknikal Malaysia Melaka (UTeM) was used as the dataset. The case study separates into various groups (excellent, honors and pass). Secondly, the study proposed a responsive web application leveraging a Google Visualization Feature to self-check individual academic performance. The goal of this app is to assist users in evaluating individual student performance and assist management in planning for continual quality improvement using the web and mobile apps. The marketing segments include students, academics, university, and school administration for analysis and evaluate the individual student’s performance.
- 13 July 2023
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 48 (11) , 15419-15434
Optimal Economic Dispatch to Minimize Load Shedding and Operation Cost for Networked Microgrids
- 13 July 2023
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 48 (11) , 15419-15434
Optimal Economic Dispatch to Minimize Load Shedding and Operation Cost for Networked Microgrids
- Open Access
- 1 November 2020
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 20 (2) , 619-626
Performance of double chamber microbial fuel cell: effect of waste water, electrode thickness and distance
This paper presents the performance evaluation of a double chamber microbial fuel cell (MFC) to obtain the maximum amount of power production. Previous works have shown that the performance of a double chamber MFC varies depending on the design of the MFC and the type of waste water. Therefore, various MFC tests were conducted to obtain the maximum amount of power production by varying the distance of electrodes and thickness of the electrode. The types of water were also varied (i.e., fertilizer water, lake water, and soil water) to highlight the effect of the expected different amount of microbes. The experimental results demonstrated that the thicker anode (0.6 cm) and the shorter distances between electrodes (15 cm) showed higher amount of power production in all the three types of waste water. Furthermore, the fertilizer water generated a higher amount of power compared to the soil and lake water.
- 1 November 2020
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 20 (2) , 619-626
Open AccessPerformance of double chamber microbial fuel cell: effect of waste water, electrode thickness and distance
This paper presents the performance evaluation of a double chamber microbial fuel cell (MFC) to obtain the maximum amount of power production. Previous works have shown that the performance of a double chamber MFC varies depending on the design of the MFC and the type of waste water. Therefore, various MFC tests were conducted to obtain the maximum amount of power production by varying the distance of electrodes and thickness of the electrode. The types of water were also varied (i.e., fertilizer water, lake water, and soil water) to highlight the effect of the expected different amount of microbes. The experimental results demonstrated that the thicker anode (0.6 cm) and the shorter distances between electrodes (15 cm) showed higher amount of power production in all the three types of waste water. Furthermore, the fertilizer water generated a higher amount of power compared to the soil and lake water.
- Open Access
- 1 June 2017
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 7 (3) , 1112-1124
Comparative Study in Determining Features Extraction for Islanding Detection using Data Mining Technique: Correlation and Coefficient Analysis
A comprehensive comparison study on the datamining based approaches for detecting islanding events in a power distribution system with inverter-based distributed generations is presented. The important features for each phase in the island detection scheme are investigated in detail. These features are extracted from the time-varying measurements of voltage, frequency and total harmonic distortion (THD) of current and voltage at the point of common coupling. Numerical studies were conducted on the IEEE 34-bus system considering various scenarios of islanding and non-islanding conditions. The features obtained are then used to train several data mining techniques such as decision tree, support vector machine, neural network, bagging and random forest (RF). The simulation results showed that the important feature parameters can be evaluated based on the correlation between the extracted features. From the results, the four important features that give accurate islanding detection are the fundamental voltage THD, fundamental current THD, rate of change of voltage magnitude and voltage deviation. Comparison studies demonstrated the effectiveness of the RF method in achieving high accuracy for islanding detection.
- 1 June 2017
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 7 (3) , 1112-1124
Open AccessComparative Study in Determining Features Extraction for Islanding Detection using Data Mining Technique: Correlation and Coefficient Analysis
A comprehensive comparison study on the datamining based approaches for detecting islanding events in a power distribution system with inverter-based distributed generations is presented. The important features for each phase in the island detection scheme are investigated in detail. These features are extracted from the time-varying measurements of voltage, frequency and total harmonic distortion (THD) of current and voltage at the point of common coupling. Numerical studies were conducted on the IEEE 34-bus system considering various scenarios of islanding and non-islanding conditions. The features obtained are then used to train several data mining techniques such as decision tree, support vector machine, neural network, bagging and random forest (RF). The simulation results showed that the important feature parameters can be evaluated based on the correlation between the extracted features. From the results, the four important features that give accurate islanding detection are the fundamental voltage THD, fundamental current THD, rate of change of voltage magnitude and voltage deviation. Comparison studies demonstrated the effectiveness of the RF method in achieving high accuracy for islanding detection.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 797-801
Effect of slot-width in slot-type linear motor
This paper discuss about the effect of slot-width in slot-type linear motor. Linear motor is a device that produces linear motion without using any mechanical transmission to convert from rotary motion to linear motion. The main objective of this paper is to investigate the effect of slot-width in slot-type linear motor. The force needs to be maintained for used in food processing application. Besides that, the slot-width is adjusted to obtain long displacement for the mover to move. Ansys Maxwell software is used to simulate the performance for this innovation. The variable parameters are the height of slot pole shoe, gap between coils, number of turns and height of coil. This investigation can give an idea to design the new device that requires compression method. The new device will help to overcome and solve the weakness of the conventional compression method. In conclusion, this research provides overview and guidelines of slot-type linear motor for food processing application.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 797-801
Effect of slot-width in slot-type linear motor
This paper discuss about the effect of slot-width in slot-type linear motor. Linear motor is a device that produces linear motion without using any mechanical transmission to convert from rotary motion to linear motion. The main objective of this paper is to investigate the effect of slot-width in slot-type linear motor. The force needs to be maintained for used in food processing application. Besides that, the slot-width is adjusted to obtain long displacement for the mover to move. Ansys Maxwell software is used to simulate the performance for this innovation. The variable parameters are the height of slot pole shoe, gap between coils, number of turns and height of coil. This investigation can give an idea to design the new device that requires compression method. The new device will help to overcome and solve the weakness of the conventional compression method. In conclusion, this research provides overview and guidelines of slot-type linear motor for food processing application.