Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Seyit Mehmet Demet has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Synergistic and Antagonistic Effects of Hybridization and MWCNT Reinforcement on the Solid Particle Erosion of Glass/Carbon Fiber Composites

    by Seyit Mehmet Demet

    A systematic investigation into the solid particle erosion (SPE) of monolithic, sandwich-type hybrid and multi-scale (Multi Wallet Carbon Nanotube (MWCNT)-reinforced) glass/carbon fiber composites was performed confirming to the ASTM G76-18 standard, utilizing angular alumina erodent (~600 µm) at 34 m/s across key impingement angles of 30°, 45°, 60°, and 90°. The analysis reveals a profound performance dichotomy dictated by the governing wear mechanism. At the shear-dominated 30° angle, where maximum material loss was observed, hybridization consistently enhanced erosion resistance relative to both monolithic benchmarks. This synergy, however, contrasts sharply with the nuanced behavior under the 90° impact-dominant regime; here, although strategically hybridizing a brittle CFRP with tougher glass fibers reduced the erosion rate (ER) by a remarkable ~50%, this benefit was compromised by the matrix embrittlement induced by MWCNT incorporation. This work clarifies the difference between shear-dominated erosion in the ductile regime and fracture toughness under impact-dominated conditions.


  • Influence of Temperature and Stress Ratio on Low‐Cycle Fatigue Life Prediction of UD ‐ CFRCs Considering Stiffness Degradation

    by Seyit Mehmet Demet, Okan Demir

    This study explores the feasibility of stress‐based and residual‐strength‐based methodologies for fatigue life prediction of unidirectional carbon fiber‐reinforced composites (UD‐CFRCs) under low‐cycle fatigue (LCF) loading. The influence of temperature and stress ratio on stiffness degradation is also investigated. Stiffness degradation increased with increasing temperature, resulting in reduced fatigue life. Similarly, higher stress ratios accelerated stiffness degradation in the UD‐CFRCs. However, increasing stress ratios also prolonged Stage II, the cumulative damage progression phase, consequently increasing fatigue life. To evaluate predictive capabilities, two distinct LCF failure models were employed: one based on the Basquin equation and the other on residual strength. These models were applied across three temperatures and four stress ratios, and their results compared. The Basquin equation‐based model provided better agreement with experimental observations.


  • Open Access

    Solid Particle Erosion Behaviors of Walnut Shell‐Filled Acrylic‐Styrene‐Acrylate ( ASA ) and Polycarbonate/Acrylic‐Styrene‐Acrylate ( PC / ASA ) Thermoplastic Blend Biocomposites

    by Harun Sepetcioglu, Seyit Mehmet Demet, İdRis Karagöz, Mehmet Bagci

    The aim of this study is to investigate the solid particle erosion behavior of walnut shell (WS)‐filled acrylic‐styrene‐acrylate (ASA) and polycarbonate/acrylic‐styrene‐acrylate (PC/ASA) thermoplastic blend composites under various erosion conditions. Erosion resistance tests were conducted using Al 2 O 3 particles (600 μm, Mohs hardness 9) as erodent, at a velocity of 34 m/s, with impingement angles ranging from 30° to 90°. Test samples were subjected to these conditions for 24 s, and weight loss was measured to determine erosion rates. Key parameters such as density, hardness, and erosion coefficients were also evaluated. Composites with 10 wt% WS filler exhibited optimal performance, reducing erosion rates by up to 36.7% compared to unfilled PC/ASA blend. Macro and SEM imaging revealed the damage mechanisms, showing less material loss and better surface durability in WS‐filled composites. This study demonstrates that incorporating WS into ASA and PC/ASA matrices not only improves erosion resistance but also aligns with the goal of sustainable material development. The results suggest that these composites could be highly effective in industries where materials are exposed to wear and tear from abrasive forces, such as in construction or automotive applications.


  • Open Access

    Grafen Nanoplaka Katkılı Bazalt Elyaf Takviyeli Kompozit Boruların İç Yüzey Erozif Aşınma Direncinde Aşındırıcı Partikül Hızının Rolünün İncelenmesi

    by Seyit Mehmet Demet

    Bu çalışmada [±55]4 sarım konfigürasyonunda filament sarım tekniği ile imal edilen iki farklı kompozit borunun boru içi malzeme akşının olduğu alt yapı ve malzeme aktarım uygulamalarında erozif aşınmaya maruz kalabilecek boru iç yüzeyinin erozyon davranışı dikkate alınarak araştırılmıştır. Bazalt elyaf takviyeli kompozit boru (BETKB) ile ağırlıkça %0,25 grafen nanoplakalar ile güçlendirilmiş bazalt elyaf takviyeli kompozit boruların (GNP/BETKB) katı partikül erozyon davranışları yapılan deneylerden elde edilen sonuçlar dikkate alınarak karşılaştırılmıştır. Dört farklı çarpma hızında (23 m/s, 28 m/s, 34 m/s, 53 m/s) ve üç farklı çarpma açısında (30, 45, 60) alümina aşındırıcı partiküller boru iç yüzeyine çarptırılarak elde edilen erozyon oranı değerlendirildiğinde grafen nanoplaka takviyesinin bazalt elyaf takviyeli boruda erozyon aşınmasına karşı direnci artırdığı görülmüştür. Erozyon oranının oransal değişiminin de incelendiği grafiklerde de sunulduğu üzere 28 m/s çarpma hızında %50’ye yakın bir erozyon oranı azalımı grafen nanoplaka takviyesi sayesinde elde edilmiştir. Her iki borunun aşınma modelinin yarı sünek aşınma modeline uygun bir davranış sergilediği belirlenmiştir.


  • Open Access

    A comprehensive experimental study of enhanced solid particle erosive resistance on the inner/outer surface of graphene nanoplatelets modified basalt/epoxy composite pipe

    by Harun Sepetcioglu, Seyit Mehmet Demet, Mehmet Bagci

    Basalt fiber reinforced polymer (BFRP) composite pipe is an excellent alternative to glass and carbon fiber reinforced composite pipes in industry and promising in high recycling for polymer composite used in aerospace, marine, and automotive. To enhance the solid particle erosion (SPE) properties of filament‐wound BFRP composite pipe while preserving its mechanical properties, reinforced BFRP composite pipes were prepared to employ non‐functionalized graphene nanoplatelets (GnPs) at a reinforcement concentration of 0.25 wt.% and ultrasonication mixing technique. The SPE behavior of GnPs reinforced and non‐reinforced BFRP composite pipes were characterized by axial and radial positioning of the inner and outer surfaces of the pipes. In each case, the erosion rates of these composite pipes were evaluated at five impingement angles (30°, 45°, 60°, 75°, and 90°) and an impact velocity of 34 m/s. The erosion response of both BFRP composite pipes' outer surfaces showed a semi‐ductile in the axial positioning, with a maximum erosion rate at a 60° impingement angle. However, these composite pipes' inner surfaces in the same positioning presented a maximum erosion rate at a 45° impingement angle. Besides, it is explored that the GnPs contribute to an improvement of approximately 10%–55% in erosive wear resistance of the non‐reinforced BFRP composite pipes. The damage analysis of eroded surfaces was examined through scanning electron microscopy (SEM), and the GnPs effect upon composite pipes' erosion micromechanisms was presented and discussed in detail.Highlights: GnPs increased the BFRP composite pipe's erosion resistance. Erosion rate on the inner surface increases due to particle accumulation. GnPs improved erosion behavior via solid lubrication and mechanical properties.


  • Open Access

    Solid Particle Erosion Behavior on the Outer Surface of Basalt/Epoxy Composite Pipes Produced by the Filament Winding Technique

    by Seyit Mehmet Demet, Harun Sepetcioglu, Mehmet Bagci

    Basalt/epoxy composite pipes in a [±55]4 winding configuration were produced on CNC filament winding machines (10 N fiber tension and ~11 mm bandwidth). In the experiments, a 34 m/s impact velocity was set using the double-disc method, and five different particle impingement angles (30, 45, 60, 75, and 90°) were used to determine the erosive effect on the outer surfaces of filament wound composite pipes under the influence of 600 μm erodent particles with angular geometry in the test set, complying with the ASTM G76-95 standard. The winding patterns in the lamina (±55 angle-ply laminate region) and zigzag (±55 zigzag region) regions of BFR/EP pipes were determined to have significant effects on solid particle erosion resistance, as evidenced by the SEM images.


  • Open Access

    Filament sarım Bazalt / Epoksi kompozit boruların iç yüzey erozif aşınma davranışına partikül hızı ve çarpma açısının etkisi

    by Seyit Mehmet Demet, Harun Sepetçi̇oğlu, Mehmet Bağci

    Kompozit malzemeler birçok alanda özellikle metal esaslı malzemelere alternatif olarak uygulama alanı bulmaktadır. Bu deneysel çalışmada Bazalt Elyaf Takviyeli Epoksi (BET/EP) kompozit boruların savunma sanayi, denizcilik, alt yapı ve aktarım tesislerinde kullanımı dikkate alınmıştır. Bu amaçla yüksek kimyevi ve ısıl denge, iyi mukavemet, sıcaklık/elektrik ve ses yalıtım özellikleri de gösteren Bazalt Elyaf Takviyesi (BET) tercih edilmiş olup Epoksi (EP) matris ilavesiyle CNC filament sarım makinelerinde [±55]4 sarım konfigürasyonunda kompozit borular ürettirilmiştir. Boru içerisinde partiküllü akışın olduğu uygulamaların temelinde farklı hızlara sahip aşındırıcıların boru içerisindeki akış yönü doğrultusunda farklı açılarda çarpması amaçlanmıştır. Boru içi katı partikül erozif aşınmayı araştırmak için, ASTM G76-95 standardıyla uyumlu deney setinde çift disk metodu kullanılarak belirlenen 23, 28, 34 ve 53 m/s çarpma hızlarındaki açısal geometriye sahip ~600 m aşındırıcı partiküller, 30°, 45° ve 60° olmak üzere üç farklı çarpma açısında BET/EP kompozit boruların iç yüzeyine etki edecek şekilde tekrarlı deneyleri yapılmış ve elde edilen sonuçlar yorumlanmıştır.


  • An analysis of the effect of pressure angle change on bending fatigue performance in asymmetrical spur gears

    by Seyit M Demet, Ali S Ersoyoğlu

    In this study, the fatigue performances of symmetrical and asymmetrical spur gears were analyzed by performing single tooth bending fatigue tests. The gears tested were determined to be symmetrical spur gears with a 20°/20° pressure angle, asymmetrical spur gears with a 20°/22° pressure angle, and asymmetrical spur gears with a 20°/25° pressure angle. These gears were made of AISI 4140 material. Single tooth bending fatigue tests were performed under variable loads. Considering the tests performed at the same torque values in asymmetrical spur gears with a 20°/22° pressure angle compared to symmetrical spur gears with a 20°/20° pressure angle, a statistically significant increase in performance was achieved at close to 90%. While gears with 20°/20° and 20°/22° pressure angles break at the tooth root, tooth flank fracture was observed in relatively high numbers of cycles in asymmetric spur gears with a 20°/25° pressure angle. It was observed that the formation of tooth flank damage negatively affected the fatigue performance.


  • Experimental investigation of wear behaviors of bronze and carbon-reinforced polytetrafluoroethylene alloy pivot pin bearings

    by H Imrek, Sm Demet

    Due to their superior features, such as low coefficients of friction, resistance against chemical effects, and good strength-to-weight ratio, polymer-based composite bearings are widely used in industries. Polymer composite bearing calculations are made based on experimental study data. In this study, experimental investigations were conducted on polytetrafluoroethylene composite radial bearings reinforced with 35% carbon and 40% bronze material where bearing loads, sliding distances, and wear were taken into consideration. The results for both materials are given graphically and compared with each other. In accordance with the results, it was considered that polytetrafluoroethylene/bronze composite film thickness and film composition on the surfaces extensively affect wear rate. It was found that these films' thicknesses depends on adhesion between steel and composite surfaces, cohesive properties of composite, load, and sliding distance.