Karim Abbaszadeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Karim Abbaszadeh has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Abbaszadeh
1 shared publication- Ahmad Naderi
Cluster of Excellence, Sustainable and Energy-Efficient Aviation (SE2A), Technische Universitt Braunschweig, Braunschweig, Germany
1 shared publication Amin Saied
Electrical Engineering Department, K.N. Toosi University of Technology, Tehran, Iran
1 shared publicationFarhad Rezaee Alam
KN Toosi Univ Technol, Dept Elect & Comp Engn, Tehran, Iran
1 shared publication- Farhad Rezaee-Alam
Departement of Electrical Engineering, Lorestan University, 68151-44316, Khorramabad, Lorestan, Iran
1 shared publication Mohammad Khalilzadeh
Electrical Engineering Department Khajeh Nasir Toosi University of Technology (KNTU) Tehran Iran
1 shared publication
Latest Publications
- Open Access
- 1 October 2016
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 9 (12) , 2394-2403
High step‐up DC–DC converter with input current ripple cancellation
In this study, a new high step‐up dc–dc converter is proposed. The proposed converter has two switches that operate in two operational modes. In the first case, both switches are turned on simultaneously, where the voltage gain would be similar to cascaded boost converter but the input current ripple will not be removed. Thus, the high voltage conversion ratio can be achieved with a suitable duty‐cycle. In this case, the performance of the converter has been investigated in two continuous and discontinuous conduction modes. In the second case, two switches operate inversely. In this case, in addition to having high voltage conversion ratio, the input current ripple is removed by a pre‐selected duty cycle. The results of the steady‐state operation of the converter are studied in both discontinuous conduction mode and continuous conduction mode. Finally, a 100 W prototype of the proposed converter has been implemented in the laboratory for evaluating its performance.
- 1 October 2016
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 9 (12) , 2394-2403
Open AccessHigh step‐up DC–DC converter with input current ripple cancellation
In this study, a new high step‐up dc–dc converter is proposed. The proposed converter has two switches that operate in two operational modes. In the first case, both switches are turned on simultaneously, where the voltage gain would be similar to cascaded boost converter but the input current ripple will not be removed. Thus, the high voltage conversion ratio can be achieved with a suitable duty‐cycle. In this case, the performance of the converter has been investigated in two continuous and discontinuous conduction modes. In the second case, two switches operate inversely. In this case, in addition to having high voltage conversion ratio, the input current ripple is removed by a pre‐selected duty cycle. The results of the steady‐state operation of the converter are studied in both discontinuous conduction mode and continuous conduction mode. Finally, a 100 W prototype of the proposed converter has been implemented in the laboratory for evaluating its performance.
- Open Access
- 1 November 2015
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 8 (11) , 2184-2194
Non‐isolated high step‐up DC–DC converter based on coupled inductor with reduced voltage stress
In this study, a novel topology for high step‐up DC–DC converters is proposed based on coupled inductors. The proposed converter has many features, such as high conversion ratio, recycling the leakage energy of the coupled inductor, minimisation of voltage stress of components, simplicity of control and high efficiency. An optimisation process is employed to optimise coupled inductor turn ratios which minimise voltage stresses of the diodes and the switch. Minimisation of the switch voltage stress results in the use of switch with smaller on‐resistance and improvement in the overall efficiency. The operation principles and steady‐state analysis of continuous, discontinuous and boundary conduction modes are discussed in detail. The performance of the proposed converter is compared with the similar converters and it is concluded that new topology has considerable advantages over them. The simulation results verify the performance of the proposed circuit. A 250 W prototype with 400 V output voltage is implemented and the experimental results are in a good agreement with the simulation results.
- 1 November 2015
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 8 (11) , 2184-2194
Open AccessNon‐isolated high step‐up DC–DC converter based on coupled inductor with reduced voltage stress
In this study, a novel topology for high step‐up DC–DC converters is proposed based on coupled inductors. The proposed converter has many features, such as high conversion ratio, recycling the leakage energy of the coupled inductor, minimisation of voltage stress of components, simplicity of control and high efficiency. An optimisation process is employed to optimise coupled inductor turn ratios which minimise voltage stresses of the diodes and the switch. Minimisation of the switch voltage stress results in the use of switch with smaller on‐resistance and improvement in the overall efficiency. The operation principles and steady‐state analysis of continuous, discontinuous and boundary conduction modes are discussed in detail. The performance of the proposed converter is compared with the similar converters and it is concluded that new topology has considerable advantages over them. The simulation results verify the performance of the proposed circuit. A 250 W prototype with 400 V output voltage is implemented and the experimental results are in a good agreement with the simulation results.
- 31 December 2014
- Published by Taylor & Francis in Electric Power Components and Systems
- Vol. 43 (2) , 134-145
Strand Current Distribution Modeling in Turbo-generators Using Finite-element Method Based on Proposed Dual Method
—The necessity of using a 3D model is one of the main problems for modeling Roebel bar transposition in turbo-generators by the finite-element method. This article proposes a 2D dual model for computing strand current distribution in the Roebel bar of turbo-generators. Considering the leakage and mutual inductances for each strand and the coupling inductances between them, the end winding region is modeled in this 2D dual model. In this article, the Roebel bar structure including 16 strands was considered, and these distributions are calculated for different transpositions using the finite-element method. In the finite-element method model, the circulating currents are calculated by subtracting a load current at each strand from the total of strand current. Also, for different transpositions, such as 90°, 180°, 360°, and 540°, the circulating currents are calculated using an analytical method. The obtained strand current distributions from the 2D dual model have good agreement with the obtained results from the analytical method for the 180° and 360° transposed coil models.
- 31 December 2014
- Published by Taylor & Francis in Electric Power Components and Systems
- Vol. 43 (2) , 134-145
Strand Current Distribution Modeling in Turbo-generators Using Finite-element Method Based on Proposed Dual Method
—The necessity of using a 3D model is one of the main problems for modeling Roebel bar transposition in turbo-generators by the finite-element method. This article proposes a 2D dual model for computing strand current distribution in the Roebel bar of turbo-generators. Considering the leakage and mutual inductances for each strand and the coupling inductances between them, the end winding region is modeled in this 2D dual model. In this article, the Roebel bar structure including 16 strands was considered, and these distributions are calculated for different transpositions using the finite-element method. In the finite-element method model, the circulating currents are calculated by subtracting a load current at each strand from the total of strand current. Also, for different transpositions, such as 90°, 180°, 360°, and 540°, the circulating currents are calculated using an analytical method. The obtained strand current distributions from the 2D dual model have good agreement with the obtained results from the analytical method for the 180° and 360° transposed coil models.
- 1 January 2013
- Published by The Scientific and Technological Research Council of Turkey (TUBITAK-ULAKBIM) - DIGITAL COMMONS JOURNALS in Turkish Journal of Electrical Engineering and Computer Sciences
- Vol. 21 (1) , 55-70
Circulating current analysis between strands in armature winding of a turbo-generator using analytical model
In this paper, the circulating current analysis between strands is studied while considering the different transpositions in the active part and without considering the transposition in the end winding region. First, this analysis is done while only considering the slot region, and then the end winding region is added to the model. The model used for this analysis is a circuit model, including the resistance and inductance of the strands and their induced back-electromotive force (EMF). The back-EMF sources and inductances are calculated through a 2D finite element analysis (FEA) of the active part and a 3D FEA for the end winding region. For the slot region analysis, the results show that the 360° and 540° transpositions are the best. Moreover, when considering the end winding region in analysis, the results obtained show that the 540° transposition minimizes the circulating current more than any other transposition. Finally, for different transpositions, the obtained results are compared among themselves and with the results of the untransposed model.
- 1 January 2013
- Published by The Scientific and Technological Research Council of Turkey (TUBITAK-ULAKBIM) - DIGITAL COMMONS JOURNALS in Turkish Journal of Electrical Engineering and Computer Sciences
- Vol. 21 (1) , 55-70
Circulating current analysis between strands in armature winding of a turbo-generator using analytical model
In this paper, the circulating current analysis between strands is studied while considering the different transpositions in the active part and without considering the transposition in the end winding region. First, this analysis is done while only considering the slot region, and then the end winding region is added to the model. The model used for this analysis is a circuit model, including the resistance and inductance of the strands and their induced back-electromotive force (EMF). The back-EMF sources and inductances are calculated through a 2D finite element analysis (FEA) of the active part and a 3D FEA for the end winding region. For the slot region analysis, the results show that the 360° and 540° transpositions are the best. Moreover, when considering the end winding region in analysis, the results obtained show that the 540° transposition minimizes the circulating current more than any other transposition. Finally, for different transpositions, the obtained results are compared among themselves and with the results of the untransposed model.
- Open Access
- 1 January 2009
- Published by Universitatea Stefan cel Mare din Suceava in Advances in Electrical and Computer Engineering
- Vol. 9 (1) , 28-33
Cogging Torque Reduction in Brushless DC Motors Using Slot-Opening Shift
In this paper, two new methods for the stator skew are introduced. In contrary with the conventional stator skew, this paper is concentrate on the slot-opening skew. The simula-tion resu ...
- 1 January 2009
- Published by Universitatea Stefan cel Mare din Suceava in Advances in Electrical and Computer Engineering
- Vol. 9 (1) , 28-33
Open AccessCogging Torque Reduction in Brushless DC Motors Using Slot-Opening Shift
In this paper, two new methods for the stator skew are introduced. In contrary with the conventional stator skew, this paper is concentrate on the slot-opening skew. The simula-tion resu ...