Farhad Rezaee-Alam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Farhad Rezaee-Alam has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
Amin Saied
Electrical Engineering Department, K.N. Toosi University of Technology, Tehran, Iran
1 shared publication- Karim Abbaszadeh
Electrical Engineering Department K. N. Toosi University of Technology Tehran Iran
1 shared publication
Latest Publications
- Open Access
- 10 December 2025
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
An Accurate Magnetic Equivalent Circuit Model for Modeling and Analysis of Variable Reluctance Energy Harvesters
Variable reluctance energy harvester (VREH) is a good candidate of transducers to transform the environmental energy into electricity. VREHs act based on electromagnetic induction due to the variation of air-gap reluctance with the rotation of wheel. This paper presents an accurate analytical model based on magnetic equivalent circuit (MEC) model and conformal mappings (CMs) for electromagnetic modeling the VREHs, which have a large air-gap. The geometry of analyzed VREH on both sides of air-gap including the iron parts, slots, and permanent magnets (PMs) is divided into many elements in cylindrical coordinate, and each element is then replaced with an equivalent permeance model. The air-gap region is modeled with permeances calculated by the CM method, which can accurately consider the real paths of flux tubes in large air-gap. The obtained air-gap permeances are then used in MEC model for electromagnetic modeling and analysis of studied VREH, while considering the effects of slots and magnetic saturation, accurately. In final, the analytical results are verified by comparing with the corresponding results obtained through finite element method (FEM).
- 10 December 2025
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
Open AccessAn Accurate Magnetic Equivalent Circuit Model for Modeling and Analysis of Variable Reluctance Energy Harvesters
Variable reluctance energy harvester (VREH) is a good candidate of transducers to transform the environmental energy into electricity. VREHs act based on electromagnetic induction due to the variation of air-gap reluctance with the rotation of wheel. This paper presents an accurate analytical model based on magnetic equivalent circuit (MEC) model and conformal mappings (CMs) for electromagnetic modeling the VREHs, which have a large air-gap. The geometry of analyzed VREH on both sides of air-gap including the iron parts, slots, and permanent magnets (PMs) is divided into many elements in cylindrical coordinate, and each element is then replaced with an equivalent permeance model. The air-gap region is modeled with permeances calculated by the CM method, which can accurately consider the real paths of flux tubes in large air-gap. The obtained air-gap permeances are then used in MEC model for electromagnetic modeling and analysis of studied VREH, while considering the effects of slots and magnetic saturation, accurately. In final, the analytical results are verified by comparing with the corresponding results obtained through finite element method (FEM).
- Open Access
- 31 July 2024
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
Performance Analysis of Slotless Axial Flux Permanent Magnet Machines with Skewed Magnets under Loading Condition
This paper presents a new 3D analytical technique for electromagnetic modeling and analysis the slotless axial flux permanent magnet (AFPM) machines. In the proposed technique, Laplace/Poisson equation is solved in different regions while considering the magnetic scalar potential as the main variable. To consider the curvature effect and radial dependency of permanent magnets (PMs), the 3D distribution of PM magnetization is introduced based on Fourier-Bessel series. The boundary conditions are then used to determine the unknown constants of Fourier-Bessel series in air-gap region. The influence of skewed PMs on the flux-linkage of stator phases is studied by using the proposed model under no-load condition while constant keeping the volume of PMs. The proposed 3D model is also extended to calculate the air-gap magnetic field due to stator currents and to extract the inductance matrix. The dynamic performance of studied slotless AFPM motor is then analyzed under voltage-input condition. In final, the accuracy of proposed 3D technique is verified by comparing the corresponding results obtained through proposed analytical model and 3D finite element method (FEM).
- 31 July 2024
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
Open AccessPerformance Analysis of Slotless Axial Flux Permanent Magnet Machines with Skewed Magnets under Loading Condition
This paper presents a new 3D analytical technique for electromagnetic modeling and analysis the slotless axial flux permanent magnet (AFPM) machines. In the proposed technique, Laplace/Poisson equation is solved in different regions while considering the magnetic scalar potential as the main variable. To consider the curvature effect and radial dependency of permanent magnets (PMs), the 3D distribution of PM magnetization is introduced based on Fourier-Bessel series. The boundary conditions are then used to determine the unknown constants of Fourier-Bessel series in air-gap region. The influence of skewed PMs on the flux-linkage of stator phases is studied by using the proposed model under no-load condition while constant keeping the volume of PMs. The proposed 3D model is also extended to calculate the air-gap magnetic field due to stator currents and to extract the inductance matrix. The dynamic performance of studied slotless AFPM motor is then analyzed under voltage-input condition. In final, the accuracy of proposed 3D technique is verified by comparing the corresponding results obtained through proposed analytical model and 3D finite element method (FEM).
- 31 December 2014
- Published by Taylor & Francis in Electric Power Components and Systems
- Vol. 43 (2) , 134-145
Strand Current Distribution Modeling in Turbo-generators Using Finite-element Method Based on Proposed Dual Method
—The necessity of using a 3D model is one of the main problems for modeling Roebel bar transposition in turbo-generators by the finite-element method. This article proposes a 2D dual model for computing strand current distribution in the Roebel bar of turbo-generators. Considering the leakage and mutual inductances for each strand and the coupling inductances between them, the end winding region is modeled in this 2D dual model. In this article, the Roebel bar structure including 16 strands was considered, and these distributions are calculated for different transpositions using the finite-element method. In the finite-element method model, the circulating currents are calculated by subtracting a load current at each strand from the total of strand current. Also, for different transpositions, such as 90°, 180°, 360°, and 540°, the circulating currents are calculated using an analytical method. The obtained strand current distributions from the 2D dual model have good agreement with the obtained results from the analytical method for the 180° and 360° transposed coil models.
- 31 December 2014
- Published by Taylor & Francis in Electric Power Components and Systems
- Vol. 43 (2) , 134-145
Strand Current Distribution Modeling in Turbo-generators Using Finite-element Method Based on Proposed Dual Method
—The necessity of using a 3D model is one of the main problems for modeling Roebel bar transposition in turbo-generators by the finite-element method. This article proposes a 2D dual model for computing strand current distribution in the Roebel bar of turbo-generators. Considering the leakage and mutual inductances for each strand and the coupling inductances between them, the end winding region is modeled in this 2D dual model. In this article, the Roebel bar structure including 16 strands was considered, and these distributions are calculated for different transpositions using the finite-element method. In the finite-element method model, the circulating currents are calculated by subtracting a load current at each strand from the total of strand current. Also, for different transpositions, such as 90°, 180°, 360°, and 540°, the circulating currents are calculated using an analytical method. The obtained strand current distributions from the 2D dual model have good agreement with the obtained results from the analytical method for the 180° and 360° transposed coil models.